Noise Emission/Vibration - Rapid BHX30 Betriebsanleitung

battery and increase the risk of fi re.
6) SERVICE
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
PRUNER SAFETY WARNINGS
WARNING!
1. Do not cut branches beyond the specifi ed
diameter, and do not cut hard items such as
metals, stone or any other non-plant materials. If
the blades are worn or damaged, please replace
blades.
2. To keep the pruner, battery and charger clean, use
a cloth or a soft brush (do not use any abrasive or
solvent-based cleaning agent).
3. Do not use the pruner in rain; water inside the tool
may damage it.
4. Do not use the pruner if it can't operate or shut
down properly.
5. To reduce the risk of harm, turn off power before
any adjustments to the pruner or changing acces-
sories.
6. Please ensure the blades are closed when not in
use. When storing the pruner it must be kept out
of the reach of CHILDREN.
7. Pruner usage shall comply with instructions sta-
ted in this manual, including methods of use and
working environment. Operation out of the tool's
range may damage the tool or reduce service life.

NOISE EMISSION/VIBRATION

■ A-weighted sound pressure level LpA= 73.2
dB(A), uncertainty K=3 dB(A). A-weighted sound
power level LwA= 84.2 dB(A), uncertainty K=3
dB(A). Recommendation for the operator to wear
hearing protection.
■ Vibration total value =1.782 m/s², uncertainty
K=1.5 m/s². The declared vibration total value has
been measured in accordance with a standard
test method and may be used for comparing one
tool with another. The declared vibration total va-
lue may also be used in a preliminary assessment
of exposure.
WARNING!
The vibration emission during actual use of the power
tool can differ from the declared total value depen-
ding on the ways in which the tool is used.
It's necessary to identify safety measures to protect
the operator that are based on an estimation of
exposure in the actual conditions of use (taking into
account all parts of the operating cycle, such as the
times when the tool is switched off and when it is
running idle, in addition to the trigger time).
TUTORIALS
Scan the QR code on the front of the manual or go
to www.rapid.com to benefi t from a 2-year warranty
6
extension and to access our tutorial videos:
- How to change the blades;
- How to handle the tool;
- How to replace wear parts.
OPERATION AND USE
TURNING ON PRUNER
Make sure the tool is in good working condition.
Insert a charged battery into the power connector of
the pruner; see picture E1.
Press power button. Battery indicator LED display
green lights and you will hear a long and a short
beep.
Double click the trigger and the blades will open
automatically.
PRUNING normal
Press trigger to progressively close blades and re-
lease the trigger to open the blades. Cutting capacity
is always 32mm on startup.
PRUNING function check
In order to check correct function, press trigger to
close and release trigger to open the blades without
cutting anything. Repeat this a few times.
PRUNING small branches
Changing to 15mm cutting capacity: Hold trigger un-
til you hear the fi rst beep, immediately release trigger.
The capacity is now 15mm.
Changing back to 32mm cutting capacity: Hold trig-
ger until you hear the fi rst beep, immediately release
trigger. The capacity is now 32mm again.
TURN OFF PRUNER
Press the trigger and hold until you hear 2 long and
1 short beep, then release trigger and the blades will
stay closed.
Press power button once to turn off the pruner, and
remove the battery.
Clean up and pack the pruner into the tool box.
FAILURE BEEP INDICATIONS
Buzzer Sound
Failure
Frequency Times
1 Battery capacity failure
2 Internal tool failure
3 blade failure
4 Internal tool failure
5 Internal tool failure
MALFUNCTION NOTES
1. If the pruner is not able to cut through an object,
release the trigger immediately and the blades will
automatically return.
2. If there is an electric or a mechanical malfunction,
power OFF immediately.
BATTERY PACK USE AND CARE
CAUTION!!
1. Only use battery charger as supplied together
with the tool, the use of other chargers may cause
fi re.
2. Only use, charge or store battery pack within the
specifi ed temperature range.
Solution Method
Check if battery capacity is low
Tool needs qualified service
Lubricate blade; see picture A6
Tool needs qualified service
Tool needs qualified service