Noise Emission/Vibration - Rapid BHX50 Betriebsanleitung

f) Do not expose a battery pack or tool to fi re
or excessive temperature. Exposure to fi re or
temperature above 130 °C/265 °F may cause
explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specifi ed in the instruc-
tions. Charging improperly or at temperatures
outside the specifi ed range may damage the
battery and increase the risk of fi re.
6) SERVICE
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
TYING MACHINE SAFETY WARNINGS
WARNING!
1. Do not remove the front cover while operating.
To avoid personal injury keep the front end tying
mouth away from any part of the body.
2. After tying operation is completed, move the tool
to the next operating position carefully. Careful
handling of the tool will protect the operator and
extend the service life of the tying machine.
3. Do not use the tying machine in rain, water inside
the tool may damage it.
4. The product is designed to tie grape vines and
other branches within the effective range of 25
mm maximum diameter. Operation out of the
range may damage the tool or reduce service life.
5. Turn off power before any attempt to remove the
feeding hook or tying wire.
6. Make sure there is enough space for the feeding
hook to move, if there is any movement interfe-
rence the tying result may be poor.
7. Do not use the tool near any fl ammable liquids or
gases. If a short circuit occurs, it may cause an
explosion or fi re.
8. The feeding system must be checked and clea-
ned frequently. If foreign materials accumulate in
the feeding track, it will affect tying operation and
increase load to the equipment. Product warranty
does not cover damage caused by poor mainte-
nance.
9. Do not attempt to repair the tool yourself, unless
you have been trained. Repair operations not
mentioned in this manual should only be perfor-
med by personnel at our service center.

NOISE EMISSION/VIBRATION

■ A-weighted sound pressure level LpA= 70.5
dB(A), uncertainty K=3 dB(A). A-weighted sound
power level LwA= 81.5 dB(A), uncertainty K=3
dB(A). Recommendation for the operator to wear
hearing protection.
■ Vibration total value =1.125 m/s², uncertainty
K=1.5 m/s²
The declared vibration total value has been
measured in accordance with a standard test
method and may be used for comparing one tool
with another.
The declared vibration total value may also be
used in a preliminary assessment of exposure.
WARNING!
The vibration emission during actual use of the power
tool can differ from the declared total value depen-
ding on the ways in which the tool is used.
It's necessary to identify safety measures to protect
the operator that are based on an estimation of
exposure in the actual conditions of use (taking into
account all parts of the operating cycle, such as the
times when the tool is switched off and when it is
running idle, in addition to the trigger time).
TUTORIALS
Scan the QR code on the front of the manual or go
to www.rapid.com to benefi t from a 2-year warranty
extension and to access our tutorial videos:
- How to change the spools
- How to handle the tool
- How to replace wearing parts
OPERATION AND USE
TURN ON TYING MACHINE
Make sure the tool is in good working condition.
Insert a charged battery into the power connector of
the tying machine
Press power button, the display lights up and you will
hear one long, 3 short and one long beep.
TYING OPERATION
Place branches inside the tying mouth
Press trigger to make a tie
Release the trigger and remove the tool from the
branch
Repeat to make next tie
LOAD NEW SPOOL USING SMART CUT
ATTENTION!! FOLLOW THOSE 8 STEPS TO
EFFECTIVELY RELOAD THE TOOL
1. Stop tying when you have 4-5 turns of remaining
wire on spool; see picture G1
2. Hold trigger 4-5s until guiding hook locks in ac-
tive position then release. Smart cut is activated;
see picture G2
! Do not turn off the machine and do not press the
trigger yet. Open pull buckle and remove outer
cover.
3. Remove used spool with remaining wire and tie in
hook mouth; see picture G3
4. Now press trigger once to deactivate smart cut
and remove tie from hook mouth; see picture G4
5. Place the new spool directly into the magazine.
Remove "end fi xing staple"; see picture G5.
6. Insert the wire fl at into the feed nozzle until the
wire reaches the end stop and press trigger to
feed the inserted wire; see picture G6
! Make sure the wire is inserted from above and
not from below, also make sure the wire is not
twisted and knotted.
7. Remove main fi xing tape; see picture G7
8. Put reel-holder cover back and press trigger until
you have an acceptable tie; see picture G8
9