Installation - Ferm BGM1001 Gebrauchsanweisung

230 V~
1 '
n = 1450/min (disc)
0
50 Hz
375 W
1 ' V = 275 m/min (belt)
0
Product: Ferm Belt sander
Type BS-702, Article number 330702
Ferm, Genemuiden, The Netherlands
Sound pressure level L pa 71 dB(A)
SERIAL NUMBER
The serial number on the machine consists of the fol-
lowing elements.
Serial nr.
ORDER NUMBER/YEAR OF CONSTRUCTION
READ THIS MANUAL CAREFULLY BEFORE USING
THE BELT SANDER!
1. SPECIFIC SAFETY RULES
BEFORE USING THE MACHINE:
1. The following points need to be checked:
- Do the connecting voltage of the machine corre-
spond with the mains voltage;
- Are the mains lead and the mains plug in a good
condition; strong, without ravels or damages.
2. For functional reasons the turning parts of this machi-
ne are not covered. Therefore it is of utmost impor-
tance to be careful. Hold the workpiece firmly, to
prevent it from slipping from your hands. Never
touch the sanding surfaces of a working machine with
your hands.
3. Avoid the use of long extension cables.
4. If necessary, secure the sanding machine with screws.
BEFORE YOU OPERATE THE MACHINE:
1. Always keep the mains cable away from moving parts
of the machine;
2. Use safety goggles;
3. Use a dust mask.
2
150 mm
915 x 100 mm
IMMEDIATELY SWITCH OF THE MACHINE
IN CASE OF:
1. defective mains plug, mains line or damage to the
mains line;
2. defective switch;
3. smoke or bad smell caused by scorched isulation.

2. INSTALLATION

Avoid the use of long extension cables. If necessary, secu-
re the sanding machine on a working bench with help of
screws through the holes in the feet of the machine fra-
me. Do not forget to leave enough space around the ma-
chine for the workpieces to be sanded.
3. DESCRIPTION
This machine combines all the advantages of a horizontal
and a vertical belt sander with those of a disc sander. Its
sturdy construction in cast iron and steel makes the ma-
chine suitable for every sanding job.
4. BEFORE PUTTING THE MACHINE
INTO OPERATION
OPERATION (SEE FIG. 1)
1. Machine frame;
2. Motor;
3. Roller stop and parallel stop;
4. Clamping handle;
5. Transport roller;
6. Sanding belt;
8. Fence;
9. Drive roller;
10. Aluminium disc;
11. Sanding disc;
12. Work plate;
13. Mitre scale;
14. Supporting arm.
ASSEMBLY
- Put the machine frame on its head and press the four
rubber stops into the foot of the frame.
- Machine frame, aluminium disc (10) and work plate
(12) are supplied in separate packaging.
- Push the aluminium disc on the shaft and fasten the
AVAILABLE SPARE PARTS FOR BS-702
REF.NR. DESCRIPTION
4 BALL BEARING 6201 ZZ
5 DRIVE ROLLER
12 ADJUSTMENT BOLT
14 IDLER ROLLER
17 PLATE TABLE
21 DRIVE PULLEY
23 MOTOR
27 BASE PLATE
28 SWITCH
30 BAR
31 ADJUSTMENT BLOCK
32 MOTOR PULLEY
33 V-BELT M21
36 ALUMINIUM DISC
39 TABLE BRACKET
40 TABLE TILT TRUNION
41 MITRE BAR
42 KNOB/BOLT FOR MITRE BAR
46 TABLE
47 MITRE GAUGE
49 SHAFT FOR DRIVE ROLLER
51 SHAFT FOR IDLER ROLLER
52 BALL BEARING 6201 ZZ
56 INDICATOR
78 CAPACITOR (6 µF = 450 VAC)
77 RUBBER FOOT
Ferm
Ferm
FERM NR.
806201
402800
402801
402802
402803
402804
402805
402806
402807
402809
402810
402811
402812
402815
402816
402817
402818
402819
402820
402821
402822
402823
806201
402824
402825
402826
35