Battery Safety - Husqvarna Aspire H50-P4A Bedienungsanweisung

• Keep first aid equipment near.
(Fig. 24)
Safety devices on the product
WARNING:
instructions that follow before you use the
product.
In this section the product's safety features, its purpose
and how checks and maintenance should be carried
out to ensure that it operates correctly. See instructions
Maintenance on page 334 to find
under the heading
where these parts are located on your product.
The life span of the product can be reduced and the risk
of accidents can increase if product maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
WARNING:
defective safety components. The product's
safety equipment must be inspected and
maintained as described in this section.
If your product fails any of these checks,
contact your service agent to get it repaired.
CAUTION:
on the machine requires special training.
This is especially true of the machine's
safety equipment. If your machine fails
any of the checks described below you
must contact your service agent. When
you buy any of our products we guarantee
the availability of professional repairs and
service. If the retailer who sells your
machine is not a servicing dealer, ask him
for the address of your nearest service
agent.
To do a check of the user interface
The green LEDs (A) show the state of charge. The
green LEDs also show that the product is on.
1. Push and hold the on/off button (B). (Fig. 25)
a) The product is on when the green LEDs (A) are
on.
b) The product is off when the green LEDs (A) are
off.
Troubleshooting on page 335 if the warning
2. Refer to
indicator (C) flashes.
To do a check of the front handle trigger
1. Make sure that the power trigger and the front
handle trigger moves freely and that the return
spring works correctly.
2. Start the product.
330
Read the warning
Never use a product with
All servicing and repair work
3. Push the front handle trigger. (Fig. 26)
4. Push the power trigger. (Fig. 27)
5. Release the front handle trigger or power trigger and
make sure that the cutting attachment stops fully.
To do a check of the hand guard
The hand guard prevents hands from accidental contact
with the blades.
1. Stop the product.
2. Remove the battery.
3. Check that the hand guard is attached correctly.
4. Examine the hand guard for damages.
To do a check of the blades and blade guards
The longer parts of the blades (A) operate as blade
guards.
1. Stop the product.
2. Remove the battery.
3. Put on gloves.
4. Make sure that the blades and blade guards are
not damaged or bent. Replace the blades and blade
guards if they are damaged or bent. (Fig. 28)

Battery safety

WARNING:
general instructions. Failure to observe the
safety and general instructions may result
in electric shock, fire and / or serious injury.
Keep all the safety information and general
instructions for future reference.
• These safety instructions apply only to 18V Li-ion
rechargeable batteries for the POWER FOR ALL
system.
• Use the rechargeable battery only in products
from POWER FOR ALL System partners. 18 V
rechargeable batteries labelled with POWER FOR
ALL are fully compatible with the following products:
– All products of the 18V POWER FOR ALL battery
system.
– All 18 V products from POWER FOR ALL System
partners.
• Observe the battery recommendations in the
operating manual of your product. Only this way
can the rechargeable battery and the product be
operated without danger and the rechargeable
batteries protected from hazardous overloading.
• Only charge the batteries using chargers
recommended by the manufacturer or by POWER
FOR ALL system partners. A charger that is suitable
for one type of battery may pose a fire risk when
used with a different battery.
• The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the
Read all the safety and
1888 - 004 - 22.09.2022