Inhaltsverzeichnis
Werbung
GB
•
Make sure that the grinding disc has been
mounted and fastened properly. Do not use
reducing rings or adapters to make the
grinding disc fit properly.
•
Treat and store grinding discs in conformance
with the supplier's instructions.
•
Do not use the machine for grinding
workpieces with a maximum thickness
exceeding the maximum grinding depth of the
grinding disc.
•
Do not use grinding discs for deburring.
•
When grinding discs have to be mounted on
the thread of the spindle, make sure that the
spindle has sufficient thread. Make sure that
the spindle is sufficiently protected and does
not touch the grinding surface.
•
Before use, inspect the grinding disc for any
damage. Do not use grinding discs which are
crack-ed, ripped or otherwise damaged.
•
Before use, let the machine run idle for 30
seconds. Immediately switch off the machine
in case of abnormal vibrations or occurrence
of another defect. Carefully inspect the
machine and grinding disc before switching
the machine on again.
•
Make sure that sparks do not put people into
danger or that they contact highly flammable
substances.
•
Make sure that the workpiece is sufficiently
supported or clamped. Keep your hands away
from the surface to be cut.
•
Always wear safety goggles and hearing
protection. If desired or required also use
another kind of protection like for example an
apron or helmet.
•
Ensure that mounted wheels and points are
fitted in accordance with the manufacturer's
instructions.
•
Ensure that blotters are used when they are
provided with the bonded abrasive product
and when they are required.
•
If a guard is supplied with the tool never use
the tool without such a guard.
•
For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the
wheel is long enough to accept the spindle
length.
•
Ensure that ventilation openings are kept
clear when working in dusty conditions. If it
should become nessesary to clear dust, first
disconnect the tool from the mains supply
(use non metallic objects) and avoid
damaging internal parts.
06
•
Though poor conditions of the electrical
mains, shortly voltage drops can appear when
starting the equipment. This can influence
other equipment (eq. blinking of a lamp). If the
mains-impedance Zmax <0.348 Ohm, such
disturbances are not expected. (In case of
need, you may contact your local supply
authority for further information.
Electrical safety
When using electric machines always observe
the safety regulations applicable in your country
to reduce the risk of fire, electric shock and
personal injury. Read the following safety
instructions and also the enclosed safety
instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class II machine – Double insulation –
You don't need any earthed plug.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
. When using a cable
2
reel always unwind the reel completely.
3. ASSEMBLY
Prior to mounting an accessory always
unplug the tool.
Mounting the side-handle
Fig. 1
The side handle can be used for both left-hand
and right-hand control.
•
Fasten the side handle for left-hand operation
on the right-hand side of the machine.
•
Fasten the side handle for right-hand
operation on the left-hand side of the
machine.
Ferm
•
Sluk altid maskinen før du fjerner stikket fra
stikkontakten.
Anvend aldrig aksellåsen til at stoppe
motoren.
5. SERVICE &
VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under
strøm, når der udføres
vedligeholdelsesarbejder på
mekanikken.
Maskinerne er udviklet til at fungere længe uden
problemer med et minimum af vedligeholdelse.
Ved at rengøre maskinen regelmæssigt og
behandle den korrekt, bidrager De til en længere
levetid for maskinen.
Fejl
For det tilfælde, at maskinen ikke fungerer
korrekt, er herunder angivet en række mulige
årsager med tilhørende løsningsforslag:
1. Maskinen fungere ikke
•
Strømmen er slukket.
•
(Forlænger) ledning er beskadiget.
2. Den elektroniske motor når ikke op til
maksimumhastighed
•
Forlængerledningen er for tynd og/eller for
lang.
•
Strømforsyningen er lavere end 230 V.
3. Maskinen overophedes
•
Udluftningskanaler er blokeret. Rengør dem
med en tør klud.
•
Maskinen er blevet overbelastet. Anvend kun
maskinen til det den er beregnet til .
4. Usædvanlig mange gnister, eller den
elektroniske motor køre uregelmæssigt
•
Der er snavs inde i motoren, eller
kulbørsterne er nedslidte.
•
Udskift kulbørsterne eller aflevér maskinen til
et særligt reparationscenter .
Reparationer må udelukkende udføres
af en autoriseret installatør eller et
autoriseret serviceværksted.
Ferm
Rengøring
Rengør regelmæssigt maskinkappen med en
blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug
en blød klud, der er vædet i sæbevand til at
fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, så som benzin, alkohol,
ammoniak, osv. Den slags stoffer beskadiger
kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en
enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual
finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres
maskinen i en solid emballage. Emballagen er så
vidt muligt lavet af genbrugsmateriale. Genbrug
derfor emballagen.
Defekte og/eller kasserede elektriske
eller elektroniske maskiner skal
afleveres på en genbrugsplads.
Garanti
Læs det separat vedlagte garantikort for
garantibetingelserne.
DK
51
Werbung
Inhaltsverzeichnis
