Hama 00087687 Bedienungsanleitung Seite 8

(F) Average wind speed & wind direction forecast
Average wind speed & direction forecast is shown next to the "WIND" icon. Press [
16 wind directions resolution: N for north, S for south, SW for south-west and so on. To view the wind speed/direction forecast for the next 3 days, press
[MODE] repeatedly until "WIND" icon appears
(G) RF Reception status
The icon shows the RF connection status between the main unit and the USB transmitter.
Main unit is successfully synchronized to the USB transmitter and is receiving weather data from USB transmitter periodically.
Flashing indicates that it is in registration mode and is searching for RF signal from USB transmitter.
Fail to receive RF signal from USB transmitter. (see "Establish RF connection with main unit" section to reconnect the USB transmitter)
(H) Last update of forecast
It shows the last update of forecast from the Internet.
"LAST UPDATE: TODAY": Forecast is updated today from the Internet
"LAST UPDATE: -1 DAY": Forecast is updated yesterday from the Internet
.... and so on
If your PC is not connected to the Internet for more than 10 days, it will show "LAST UPDATE: -- DAY" and all forecast information will show " - - " until the
PC is connected to the Internet again.
Time
(A) Network time or
(B) Sunrise/sunset time or
(C) Alarm time
(A) Network time (Auto-synchronized clock)
The clock on the main unit is synchronized to the Internet network time automatically and is adjusted for optimal accuracy.
NOTE:
• If your PC is not connected to the Internet for a long period of time, the clock display may not be accurate
• You may set the time offset (+/- 0.5, 1, 1.5 or 2 hours) of your home city in the PC program to adjust DST & time zone if necessary and the time on your
main unit will be updated accordingly Hold [CLOCK] on the main unit to set the 12/24 hour format, press [
confirm. The "M" & "D" icons will flash, press [ ] or [ ] to select day/month or month/day format for the calendar. Press [CLOCK] to confirm and
exit.
(B) Sunrise/Sunset time
To view the sunrise and sunset time of your home city, press [CLOCK] button repeatedly until the respective "SUNRISE" or "SUNSET" icon appears
(C) Alarm time
Press [ALARM] button to view the alarm time and "AL" icon will appear. Press [ALARM] again to enable & disable the alarm.
is enable. Press [CLOCK] to return to time display. Hold [ALARM] for 3 seconds to enter alarm setting mode. Press [
values and press "ALARM" to confirm setting. When alarm is going off, press [ALARM] to stop alarm for one day. Press [MODE/SNOOZE/LIGHT] to activate
snooze function
(D) Moon phase
Moon phase is displayed according to the current calendar automatically.
(E) Calendar
Press [CLOCK] repeatedly to show the time with day-of-the-week or seconds. Calendar can be displayed in day/month or month/day format. See section A
"NETWORK TIME" for setting.
Display backlight
Press MODE/SNOOZE/LIGHT for an extended backlight.
Low battery indication
Low battery indication is available for the main unit & USB transmitter. Replace the batteries and follow the setup procedure in this instruction manual
Low battery indicator
14
/WIND] to select wind speed unit between km/h, m/s, knots & mph.
(D) moon phase
(E) calender
] or [ ] to select and press [CLOCK] to
icon appears when alarm
] or [ ] to enter the desired Hr/ Min
Main unit:
USB transmitter: Next to the "Last Update" box
Important note:
You are required to set up the RF connection between the USB transmitter & main unit after battery replacement. Press [PC Search] on the main unit and
then press [TRANSMIT] on the USB transmitter. Refer "Establish RF connection with main unit" section for details.
USB Transmitter
Press [PC Search] on the main unit and then press [TRANSMIT] on the USB transmitter to enforce transmitting RF weather data and set up the RF connec-
tion with the main unit (See "USB Transmitter & program installation" section to set up the USB transmitter). USB transmitter comes with a blue light bar.
You may disable or enable the continuous light bar function by holding the [TRANSMIT] button on the USB transmitter.
NOTE:
• To run the PC program, ensure that your USB transmitter is connected properly to the PC via an USB port.
• When weather data is transmitted from the USB transmitter, the light bar will flash.
PC program
After installation, a small toolbar icon of your PC program appears on the
lower right of the Window indicating your program is running and it will
automatically access 4-day forecast information periodically while your PC is online.
You may open the above PC program window by double clicking this toolbar icon to
view the full details.
IMPORTANT NOTE: If the toolbar icon disappears (not hidden), your
PC program is terminated and no longer access the weather information from the
Internet. Restart the program again.
Home weather
Setting
Click [SETTING...] to set the home city's location & unit/time format.
Click [SET LOCATION] to set your home location. Click [SAVE] to save your setting and exit. The forecast information will be updated on your PC program
according to your new home location and send to your main unit automatically.
Update forecast
Click [UPDATE FORECAST] to manually receive 4-day forecast from the Internet and display on the program
Send to receiver
Click [SEND TO RECEIVER] to manually send the 4-day forecast data to the main unit via the USB transmitter.
It may take from than 10 minutes to 1 hour to update all of the 4-day forecast data on the main unit.
CITY 1, 2, 3 & 4
Select location
Beside your home city, you can preset & monitor the weather forecast of up to 4 different cities on your PC program.
15