Specifications - Makita LS1440 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Handle latch
2-1. Bolt
3-1. Holder
4-1. Holder
4-2. Screw
5-1. Blade guard
6-1. Blade guard
7-1. Turn base
7-2. Kerf board
8-1. Gear housing
8-2. Hex nut
8-3. Adjusting bolt
9-1. Top surface of turn base
9-2. Periphery of blade
9-3. Guide fence
10-1. Pointer
10-2. Lock lever
10-3. Miter scale
10-4. Grip
11-1. Lock lever
11-2. Switch trigger
12-1. Switch trigger
13-1. Socket wrench
14-1. Shaft lock
15-1. Socket wrench
16-1. Blade case

SPECIFICATIONS

Blade diameter
Blade body thickness
Hole diameter
Max. Miter angle
Max. Cutting capacities (H x W)
122 mm x 152 mm
-1
No load speed (min )
Dimensions (L x W x H)
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for accurate straight and miter
cutting in wood. With appropriate saw blades, aluminum
can also be sawed.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
Explanation of general view
16-2. Arrow
16-3. Saw blade
16-4. Arrow
17-1. Spindle
17-2. Inner flange
17-3. Blade
17-4. Outer flange
17-5. Hex bolt
17-6. 25.4 mm marking
18-1. Pin
18-2. Guide arm
19-1. Dust nozzle
19-2. Dust bag
19-3. Fastener
20-1. Support
20-2. Turn base
21-1. Projection
21-2. Vise knob
22-1. Vise rod
22-2. Screw
22-3. Guide fence
22-4. Vise knob
22-5. Vise arm
23-1. Vise rod
23-2. Screw
23-3. Vise knob
0°
ENE004-1
ENF002-2
Miter angle
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
5
23-4. Vise arm
23-5. Guide fence
25-1. Horizontal vise
25-2. Spacer block
25-3. Aluminum extrusion
25-4. Guide fence
26-1. Guide fence
26-2. Wood facing
27-1. Set plate
27-2. Holder
27-3. Screw
28-1. Handle latch
30-1. Hex bolt
31-1. Guide fence
31-2. Triangular rule
32-1. Pointer
32-2. Screws
32-3. Miter scale
33-1. Gear housing
33-2. Hex lock nut
33-3. Arm
34-1. Limit mark
35-1. Screwdriver
35-2. Brush holder cap
2.0 mm - 2.6 mm
25 mm and 25.4 mm
Left 45° , Right 45°
45° (left and right)
122 mm x 115 mm
596 mm x 550 mm x 630 mm
355 mm
3,200
34.2 kg
/II
ENF100-1