simu T3.5EBHZ DC Originalanleitung Seite 9

SIMU S.A.S. au capital de 5 000 000 € - Zone Industrielle Les Giranaux - 70100 ARC-LÈS-GRAY - FRANCE - RCS VESOUL B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR87 425 650 090
These instructions apply to all T3.5EBHZ DC drive, the different versions of which are available in the current
catalogue.
Field of application: T3.5EBHZ DC drive are designed to all types of roller shutters. The installer, who must be
a motorisation and home automation professional, must ensure that the drive product is installed in accordance
with the standards in force in the country in which it is installed such as EN 13659 relating to roller shutters.
Liability: Before installing and using the drive, please read operating and installation guide carefully.
Please read these instructions carefully before installing and using the drive. In addition to following the
instructions given in this guide, the instructions detailed in the attached Safety instructions document must
also be observed. The drive must be installed by a motorisation and home automation professional, according to
instructions from SIMU and the regulations applicable in the country in which it is commissioned. It is prohibited
to use the drive outside the field of application described above. Such use, and any failure to comply with
the instructions given in this guide and in the attached Safety instructions document, absolves SIMU of any
liability and invalidates the warranty. The installer must inform its customers of the operating and maintenance
conditions for the drive and must provide them with the instructions for use and maintenance, and the attached
Safety instructions document, after installing the drive. Any After-Sales Service operation on the drive must be
performed by a motorisation and home automation professional. If in doubt when installing the drive, or to obtain
additional information, contact a SIMU adviser or go to the website www.simu.com.
i
AUTOSUN 2 BHZ SYSTEM PRESENTATION
The T3.5EBHZ DC motor is part of the AUTOSUN 2 BHZ system which references are available in the current
catalogue. It is a powered system working with solar energy. The electrical energy supplied by the solar panel
is stored inside the battery of the system. This system was developed to run into the following countries:
France, Germany, England, Belgium, Netherlands, Czech Republic, Poland, Ireland, Spain, Portugal, Italy,
Greece, Switzerland, Luxembourg, Denmark, Austria, Hungary, USA (excluding Alaska), Australia and Turkey.
For other countries, please contact us.
4
+
Ref. 9019722
Ref. 9020638
i
• The weight of roller shutter must comply with the charts determined for the motors. Maximum shutter
heights are: 1600 mm for 3Nm motors, 2300 mm for 6Nm motors and 2500 mm for 10Nm motors.
• The solar panel should always be placed on the shutter housing so as to be as exposed as possible to the
sun's rays.
• Autonomy of the system without battery charging: 45 days for 2 cycles / day (1 cycle = 1 UP and 1 DOWN),
with a new battery loaded at 100% and at 20°C. In exceptional years, use the battery charger ( 4 ) to recharge
the AUTOSUN 2 BHZ's battery.
T3.5EBHZ DC
(12VDC)
1
2
5
+
Ref. 9019683
6
AUTOSUN 2 BHZ system components :
1- 12V motor T3.5EBHZ DC, 3, 6 or 10 Nm.
2- SOLAR PANEL-12V : « 3.2W SOLAR PANEL » ;
3.2W/ Voc : 21V/ Isc : 196 mA.
3- Batteriy NiMh - 12V/ 2.2Ah :
- « Naked battery autosun 2 »
or
- « Batterie coque equip.»
In option :
3
4- Battery charger ref.: 9020638. Allows rapid recharging of
the battery ( 3 ) for the AUTOSUN 2 BHZ system (see §10).
5- Solar Panel bracket ref.: 9019683
6- Extension cable 5m réf. : 9019722
EN – ORIGINAL INSTRUCTIONS
5148477A
i
-20°C / +60°C
EN 1/8