Makita UM600D Betriebsanleitung Seite 16

Installing or removing the shear
blades for grass shear
Removing the shear blades
1. Remove the grass receiver and place the tool
upside down.
► Fig.11
2. While pressing the lock lever, turn the undercover
counterclockwise until
with on the lock lever.
► Fig.12
Remove the undercover, shear blades, and crank.
3.
► Fig.13: 1. Undercover 2. Shear blades 3. Crank
Installing the shear blades
Prepare the crank, undercover, and new shear
1.
blades.
► Fig.14: 1. Crank 2. Undercover 3. Shear blades
Remove the blade cover from the old shear
2.
blades, and then attach it to the new ones.
► Fig.15
Adjust the three pins so that they are lined up on
3.
the alignment line.
► Fig.16: 1. Alignment line
Apply a small amount of grease to the periphery
4.
of the crank. Attach the crank to the pins with the small
and large rounds facing up.
► Fig.17: 1. Crank
Adjust the blades and base plate so that the hole
5.
in the base plate and the two protrusions on the blades
are lined up.
► Fig.18
Turn the shear blades upside down and install
6.
them so that the pins on the tool fit in the hole on the
base plate. Make sure that the shear blades are fixed
securely in place.
► Fig.19
Place the undercover so that
7.
cover is aligned with
► Fig.20
8. While pressing the undercover, turn the under-
cover clockwise until
with on the lock lever.
► Fig.21
Make sure that the lock lever fits in the groove on
9.
the undercover.
► Fig.22: 1. Lock lever
CAUTION:
Never use the tool without install-
ing the undercover.
10. Remove the blade cover, and then turn on the tool
to check that it works properly.
on the undercover is aligned
on the under-
on the lock lever.
on the undercover is aligned
If the shear blades do not operate prop-
NOTICE:
erly, the blades are not engaging the crank prop-
erly. Remove the blades and install them again.
Installing or removing the shear
blades for hedge trimmer
Attach the blade cover before
CAUTION:
removing or installing the shear blades.
Removing the shear blades
Place the tool upside down.
1.
► Fig.23
2. While pressing the lock lever, turn the undercover
counterclockwise until
with on the lock lever.
► Fig.24
3. Remove the undercover.
► Fig.25
4. Loosen the two screws with a screwdriver and
remove the shear blades.
► Fig.26: 1. Screws
NOTE: The shear blades can be removed without
removing the screws.
Remove the crank from the shear blades.
5.
► Fig.27: 1. Crank
NOTE: The crank may remain in the tool.
Attach the blade cover and the storage case to the
removed shear blades, and then store the blades.
Installing the shear blades
Prepare the crank, undercover, and new shear
1.
blades.
► Fig.28: 1. Crank 2. Undercover 3. Shear blades
Attach the blade cover to the shear blades.
2.
► Fig.29
Adjust the three pins so that they are lined up on
3.
the alignment line.
► Fig.30: 1. Alignment line
Apply a small amount of grease to the periphery
4.
of the crank. Attach the crank to the pins with the small
and large rounds facing down.
► Fig.31: 1. Crank
Slide the shear blades so that the hole on the
5.
base plate is positioned at the center of the rings of the
blades.
► Fig.32
Turn the shear blades upside down and install them so
6.
that the pin on the tool fits in the hole on the shear blades.
Insert the claw of the base plate into the groove on the tool.
Make sure that the shear blades are fixed securely in place.
► Fig.33: 1. Claw
Tighten the two screws firmly with a screwdriver.
7.
► Fig.34: 1. Screws
16 ENGLISH
on the undercover is aligned