Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EURO • Printed in Italy • BA F016 L69 837 • AQUATAK 1300/1500 • OSW 12/01
F016 L69 837.book Seite 3 Donnerstag, 20. Dezember 2001 8:37 08
For Your Safety
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
Electrical Safety
Your machine requires an earth connection. The op-
erating voltage is 230 V AC, 50 Hz. Only use ap-
proved extension cables. Contact your Bosch Serv-
ice Center for details.
If you want to use an extension cable when operat-
ing your high pressure washer, only the following ca-
ble dimensions should be used:
2
1.5 mm
- max length 20 m
2
2.5 mm
- max length 50 m
Note: If an extension cable is used it must be
earthed and connected through the plug to the earth
cable of your supply network in accordance with pre-
scribed safety regulations.
If in doubt contact a qualified electrician or the near-
est Bosch Service Center.
WARNING! Inadequate extension cables can be
dangerous. Extension cable, plug and socket
must be of watertight construction and intended
for outdoor use.
Cable connections should be kept dry and off
ground.
It is recommended for increased electrical safety to
use a Residual Current Device (RCD) with a tripping
current of not more than 30 mA. Always check your
RCD every time you use it.
For products not sold in GB: WARNING: For
safety, it is essential that the mains plug 6 attached
to the machine is fitted to the power supply cable.
The couplings of connection leads must be pro-
tected against splashes and the coupling sockets on
the leads must be made of rubber or coated with
rubber. Fixing means for the connection leads must
be used.
If the supply cord is damaged, it must be replaced by
a Bosch Service Center.
Products sold in GB only: Your machine is fitted with
an approved 13 A (BS 1363/A) electric plug and is
protected by a 13 A fuse (ASTA Approved to
BS 1362).
If the fitted plug is not suitable for your socket out-
lets, it should be cut off and an appropriate plug fit-
ted in its place.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted
into a 13 A socket elsewhere.
14 • F016 L69 837 • TMS • 14.12.01
Assembly
Water connection
Screw connector 7 onto machine water inlet connec-
A
tion 8. (see figure
Attach water supply hose (not supplied) to the mains
water supply and machine. (see figure
Connecting high pressure water supply
hose/nozzle
Securely screw high pressure hose 6 onto machine
at connection 9. (see figure
Inserting the extension lance 4 into the power gun 3.
Depress and turn the extension lance 4 90° clock-
wise to lock in place. (see figure
Inserting the vario-jet-fan nozzle 10 into the exten-
sion lance 4 and turn the vario-jet-fan nozzle 10
clockwise until it "clicks", it is now locked in place.
E
(see figure
)
Adjustments and using different
nozzles
Vario-jet-fan nozzle
(yellow-1300 Si/green-1500 Si colour coded)
Twist the nozzle sleeve to adjust from a pencil to a
fan jet and vice versa. (see figure
To apply the detergent move the nozzle from high
pressure mode to low pressure mode by pulling the
nozzle forward. (see figure
To adjust the spray patten twist the nozzle.
F
(see figure
)
Roto nozzle
(yellow-1300 Si/orange-1500 Si colour coded)
Turn the Jet-fan nozzle 10 anti-clockwise to extract
it from the extension lance 4. (see figure
Inserting the Roto nozzle 12 into the extension
lance 4 and turn the Roto nozzle 12 clockwise until
it "clicks", it is now locked in place. (see figure
Starting and Stopping
Starting
Open water tap.
Press the safety lock 1 to release the trigger 2. Fully
press the trigger 2 until there is a constant flow of
water. Release trigger 2. Press the trigger safety
K
lock. (see figure
Press button (
) on main switch 5.
Point the power gun 3 downwards. Press the trigger
safety lock to release the trigger 2. Fully press the
trigger 2. (see figure
English - 3
)
A
B
/
)
C
)
D
)
F
)
G
)
I
)
)
K
)
J
)
Werbung
Inhaltsverzeichnis
