Starting And Stopping - Bosch aquatak 120 i Bedienungsanleitung

EURO • Printed in Italy • BA F016 L69 836 • AQUATAK 120 • GB • OSW 12/01
F016 L69 836.book Seite 3 Donnerstag, 13. Dezember 2001 3:56 15
For products not sold in GB: WARNING: For
safety, it is essential that the mains plug attached to
the machine is fitted to the power supply cable . The
couplings of connection leads must be protected
against splashes and the coupling sockets on the
leads must be made of rubber or coated with rubber.
Fixing means for the connection leads must be
used.
If the supply cord is damaged, it must be replaced by
a Bosch Service Center.
Products sold in GB only: Your machine is fitted with
an approved 13 A (BS 1363/A) electric plug and is
protected by a 13 A fuse (ASTA Approved to
BS 1362).
If the fitted plug is not suitable for your socket out-
lets, it should be cut off and an appropriate plug fit-
ted in its place.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted
into a 13 A socket elsewhere.
Assembly
Water connection
Screw connector 7 onto machine water inlet connec-
A
tion 8. (see figure )
Attach water supply hose (not supplied) to the mains
water supply and machine. (see figure
Connecting high pressure water supply
hose / nozzle
Securely screw high pressure hose 6 onto machine
at connection 9. (see figure
Inserting the extension lance 4 into the power gun 3.
Depress and turn the extension lance 4 90° clock-
wise to lock in place. (see figure
Inserting the vario-jet-fan nozzle 10 into the exten-
sion lance 4 and turn the vario-jet-fan nozzle 10
clockwise until it "clicks", it is now locked in place.
E
(see figure )
14 • F016 L69 836 • TMS • 10.12.01
Vario-jet-fan nozzle (lilac colour coded)
Twist the nozzle sleeve to adjust from a pencil to a
fan jet and vice versa. (see figure
To apply the detergent move the nozzle from high
pressure mode to low pressure mode by pulling the
nozzle forward. (see figure
To adjust the spray patten twist the nozzle.
(see figure
Roto nozzle (red colour coded)
Turn the Jet-fan nozzle 10 anti-clockwise to extract
it from the extension lance 4. (see figure
Inserting the Roto nozzle 12 into the extension
lance 4 and turn the Roto nozzle 12 clockwise until
it "clicks", it is now locked in place. (see figure
Starting
Open water tap.
Press the safety lock 1 to release the trigger 2. Fully
press the trigger 2 until there is a constant flow of
water. Release trigger 2. Press the trigger safety
A B
/ ) lock. (see figure
Press button (
Point the power gun 3 downwards. Press the trigger
safety lock to release the trigger 2. Fully press the
trigger 2. (see figure
C
)
Stopping
Release trigger 2. Press the trigger safety lock. The
D
)
power gun is now locked and can not be operated
accidentally. (see figure
Press button (
Close water tap. Unplug the machine from the elec-
tric supply.
Press the trigger safety lock 1 to release the trig-
ger 2. Fully press the trigger 2 until there is no more
water in the machine. Release trigger 2. Press the
trigger safety lock 1. (see figure
Disconnect water supply hose from machine and
water supply.
English - 3
Adjustments and using different
nozzles
G
F
)

Starting and Stopping

K
)
) on main switch 5.
K
)
K
)
) on the main switch 5.
F )
)
I
)
J
)
K
)