Specifications - Makita 1100 Betriebsanleitung

ENGLISH
(Original instructions)
1 Knob
2 Switch trigger
3 Lock button/Lock-off button
4 Bolts
5 Drum
6 Planer blade
7 Drum plate
8 Adjusting plate
9 Inside edge of gauge plate
10 Blade edge
11 Screws
12 Heel
13 Back side of gauge base
14 Gauge plate
15 Gauge base

SPECIFICATIONS

Model
Planing width ........................................................ 82 mm
Planing depth ......................................................... 3 mm
Shiplapping depth ................................................ 20 mm
–1
No load speed (min ) .......................................... 18,000
Overall length ..................................................... 415 mm
Net weight ............................................................. 5.1 kg
Safety class ..............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future refer-
ence.
6
Explanation of general view
16 Pan head screw
17 Planer blade locating lugs
18 Heel of adjusting plate
19 Set plate
20 Inside flank of gauge plate
21 Mini planer blade
22 Groove
23 Hex. flange head bolt
24 Makita vacuum cleaner
25 Standard (non-round) chip
cover
26 Start
27 End
28 Cutting line
29 Screw
PLANER SAFETY WARNINGS
1100
1.
2.
/II
3.
4.
ENE001-1
5.
6.
ENF002-2
7.
8.
9.
10. Before using the tool on an actual workpiece, let
GEA010-1
11. Make sure the blade is not contacting the work-
12. Wait until the blade attains full speed before cut-
13. Always switch off and wait for the blades to
14. Never stick your finger into the chip chute.
15. Do not leave the tool running. Operate the tool
16. Always change both blades or covers on the
17. Use only Makita blades specified in this manual.
30 Edge fence
31 V groove
32 Sharpening holder
33 Wing nut
34 Blade (A)
35 Blade (B)
36 Side (C)
37 Side (D)
38 Limit mark
39 Chip cover
40 Screwdriver
41 Brush holder cap
Wait for the cutter to stop before setting the tool
down. An exposed cutter may engage the surface
leading to possible loss of control and serious injury.
Hold the power tool by insulated gripping sur-
faces only, because the cutter may contact its
own cord. Cutting a "live" wire may make exposed
metal parts of the power tool "live" and could give
the operator an electric shock.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
Rags, cloth, cord, string and the like should
never be left around the work area.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Use only sharp blades. Handle the blades very
carefully.
Be sure the blade installation bolts are securely
tightened before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
piece before the switch is turned on.
ting.
come to a complete stop before any adjusting.
Chute may jam when cutting damp wood. Clean
out chips with a stick.
only when hand-held.
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
GEB010-4