Herunterladen Inhalt Inhalt Diese Seite drucken

Ferm HGM1007 Gebrauchsanweisung Seite 14

Inhaltsverzeichnis

Werbung

GB
6. MAINTENANCE
Make sure the battery is disconnected and wear protective gloves before handling
the blade.
To ensure long and reliable service, carry out the following maintenance regularly:
Check for obvious defects such as loose, dislodged or damaged blades, loose fixings and
worn or damaged components.
Check that covers and guards are undamaged and correctly fitted.
Blade maintenance:
Wear gloves when handling or cleaning the cutting blade.
Always clean the cutting blade after operation and coat it with a lubricating spray. A Lack
of lubrication to the blade can severely effect the products run time.
During longer cutting periods 15 minutes or greater it is recommended to lubricate the
blade, this will improve cutting performance and extend the batteries run time.
Careful selection of the spray should be taken as some lubricants may reduce run times
by up to 60%.
Before use: Visually check the condition of the cutting edges of the cutting blade. Check
the tightness of blade bolts
When not in use ensure that the blade is covered with the blade guard provided and that it
has been lubricated. Failure to do so may cause the blade to corrode and will severely
reduce cutting performance and battery run times.
Cleaning and storage
Remove or disconnect the battery from the tool during storage. Take care not to short the
battery contact terminals with metal objects.
Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use
water or solvents. Remove all debris especially from the ventilation slots on the motor
housing.
Always lubricate the cutting blade with protective spray before storage.
Store the hedge cutter in a secure, dry place out of reach of children.
Do not place other objects on top of the machine.
Storage outside in a damp environment such as a garden shed may cause certain items
such as the blades to corrode.
14
JEU D'OUTILS DE JARDIN SANS FIL MULTIFUNCTIONS
FTMC-12V
Les chiffres du texte suivant correspondent aux illustrations page 2 - 5.
Pour votre propre sécurité et celle de votre entourage, veuillez lire attentivement
ces instructions avant d'utiliser cet appareil. Nous vous conseillons de ranger ces
dernières dans un endroits sur pour de futures références.
Contenus
1. Données de la machine
2. Consignes de sécurité
5. Charge et recharge du pack de batteries
4. Assemblage
5. Utilisation
6. Entretien
1. DONNÉES DE LA MACHINE
Spécifications techniques
Caractéristiques du chargeur de batterie
Caractéristiques du pack de batteries
Temps de chargement du pack de batteries
Temps de fonctionnement
Vitesse à vide Tailleuse de haies
Vitesse à vide Taille-bordures
Vitesse à vide Scie de branche
Poids
* Selon la longueur et l'épaisseur des matériaux coupés.
Informations concernant le produit
Fig. 1
1.
Unité principale
2.
Commutateur de déclenchement arrière
3.
Commutateur central
4.
Commutateur frontal
5.
Verrouillage de l'inclinaison de la tête
6.
Écran de lame
7.
Rainures de ventilation
8.
Boutons de libération d'outillage
9.
Bouchon de produit
10. Protection de lame
11. Lame (+ protection)
12. Pack de batteries
Ferm
Ferm
F
230V~, 50 Hz
12 V, 3 Ah
12 heures
75 minutes*
1100/min
1050/min
180/min
1.2 kg
39

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ftmc-12v

Inhaltsverzeichnis