Optional Attachments; Maintenance - DeWalt DW719 Anweisungen

Optional attachments

The attachments, i.e. the legstand (15), extension table (16) with scale
extension (17), parallel fence (18), sliding table (19) and mitre fence (20) are
available as an option (fig. A2).
Consult your dealer for further information on the appropriate accessories.
Legstand (fig. A2 & P1)
The legstand has been designed for intstalling your saw bench as a stand-
alone machine acquiring optimum space for using the extension table (16)
and/or the sliding table (19) (fig. A2).
• Place the legstand (15) on the floor leaving enough space to use freely
any attachment mounted to the machine (fig. P1).
• Place the machine on the legstand making sure that the four feet on
the machine are located within the frame.
Extension table (fig. A2 & P2)
The extension table (16) utilises the same dovetail system for location and
can therefore be fitted onto any side of the table. Along with the table
comes a scale extension (17) to provide in optimum measuring facility, for
example when it is used in combination with the parallel fence (18) (fig. A2).
• The most suitable position is on the right-hand side of the machine (fig. P2).
• The fence assembly can be used on the extension table in the same
way as on the machine table.
Parallel fence (fig. A2 & P3)
The parallel fence (18) is used in the ripping mode to extend the ripping
guidance over the full length of the table (fig. A2).
• The most suitable position is to the right of the blade (fig. P3).
• The parallel fence can be used either on the machine table or on the
extension table.
• Adjust the fence parallel to the blade.
• Refer to the instructions for sawing in ripping mode.
Sliding table and mitre fence (fig. A2 & P4 - P6)
The sliding table (19) and extendable mitre fence with end stop (20) are
used in the ripping mode to support cross-cutting long workpieces at any
angle from 0° to 90° (fig. A2).
• The only suitable position for the sliding table is on the left-hand side of
the machine (fig. P4).
• The fence assembly can be used on the sliding table in the same way
as on the machine table.
• Replacing the fence profile, the mitre fence can be fitted to the mitre
quadrant for enhanced support and guidance. The most suitable
position is on the left-hand side of the sliding table.
• Set the blade in ripping position.
• For straight cross-cuts, set the fence at 90° to the blade (fig. P5).
• For mitre cuts, set the required angle (fig P6).
• Place the workpiece against the mitre fence.
• Before making a cut, check that the fence does not foul the blade and
that the workpiece will be cut through.
• Slowly push the table to the rear, thus feeding the workpiece along the
blade.

Maintenance

Your D WALT machine has been designed to operate over a long period
E
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Cleaning
Keep the ventilation slots clear and regularly clean the housing with a
soft cloth.
• On a weekly basis, remove sawdust from the machine.
Unwanted tools and the environment
Take your tool to an authorized D
disposed of in an environmentally safe way.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of your
D WALT tool, simply return it within 30 days, complete as purchased,
E
to the point of purchase, for a full refund or exchange. Proof of
purchase must be produced.
• ONE YEAR FREE SERVICE CONTRACT •
If you need maintenance or service for your D
12 months following purchase, it will be undertaken free of charge at
an authorized D WALT repair agent. Proof of purchase must be
E
produced. Includes labour and spare parts for the attachments.
Excludes accessories.
• ONE YEAR FULL WARRANTY •
If your D WALT product becomes defective due to faulty materials or
E
workmanship within 12 months from the date of purchase, we
guarantee to replace all defective parts free of charge or, at our
discretion, replace the unit free of charge provided that:
• The product has not been misused.
• Repairs have not been attempted by unauthorized persons.
• Proof of purchase date is produced.
This guarantee is offered as an extra benefit and is additional to
consumers statutory rights.
For the location of your nearest authorized D
please use the appropriate telephone number on the back of this
manual. Alternatively, a list of authorized D
details on our after-sales service are available on the Internet at
www.2helpU.com.
E N G L I S H
WALT repair agent where it will be
E
GUARANTEE
WALT tool, in the
E
WALT repair agent,
E
WALT repair agents and full
E
33