Using This Unit - Pioneer DEH-X6600DAB Bedienungsanleitung

Section
02

Using this unit

Removing the front panel
1 Press the detach button to release the front
panel.
2 Push the front panel upward (M) and then pull
it toward (N) you.
3 Always store the detached front panel in a pro-
tective case or bag.
Re-attaching the front panel
1 Slide the front panel to the left.
2 Press the right side of the front panel until it is
firmly seated.
Forcing the front panel into place may result in
damage to the front panel or head unit.
Turning the unit on
1 Press SRC/OFF to turn the unit on.
Turning the unit off
1 Press and hold SRC/OFF until the unit turns
off.
4
En
Selecting a source
1 Press SRC/OFF to cycle between:
DIGITAL RADIO (digital audio broadcasting)
—RADIO—CD—USB/iPod—APP (application)
—AUX
! If a source other than DIGITAL RADIO is se-
lected, you can switch to DIGITAL RADIO by
pressing DAB.
! USB MTP displays while the MTP connection
is in use.
Adjusting the volume
1 Turn M.C. to adjust the volume.
Note
When this unit's blue/white lead is connected to
the vehicle's auto-antenna relay control termi-
nal, the vehicle's antenna extends when this
unit's source is turned on. To retract the anten-
na, turn the source off.
Frequently used menu
operations
Returning to the previous display
Returning to the previous list (the folder one level
higher)
1 Press
/DIMMER.
Returning to the ordinary display
Canceling the main menu
1 Press BAND/ .
Returning to the ordinary display from the list
1 Press BAND/ .
Digital Radio (Digital Audio
Broadcasting)
To receive DAB signals, connect a DAB antenna
(AN-DAB1) sold separately to the unit.
Using this unit
DAB stands for Digital Audio Broadcasting and
has the following features:
! High sound quality (nearly as high as for
CDs, although it may be reduced in some
cases in order to allow more services to be
broadcast)
! Interference-free reception
Note
Some stations perform broadcast testing.
Basic operations
Selecting a band
1 Press BAND/
until the desired band (D1, D2,
or D3) is displayed.
Manual tuning (step by step)
1 Press c or d.
Ensemble
Service
Press .
Primary Service Component
Service
Primary Service Component
Secondary Service Component
Secondary Service Component
Press .
Some individual services in an ensemble may be
further subdivided into Service Components. The
main Service Component is called the Primary
Service Component, and any auxiliary Service
Components are called Secondary Service Com-
ponents.
Seeking
1 Press and hold c or d, and then release.
Pausing
You can use the pause function to temporarily
stop listening to a DAB.
% Press DAB to pause or resume.
! This unit stores recent broadcasts to memory
automatically. The memory capacity of this
unit will vary depending on the bit rate of the
Service Component used. The approximate
memory capacity is five minutes for 192 kbps.
! If the duration that a selection is paused ex-
ceeds the length of the memory capacity,
playback will resume from the beginning of
the selection in memory.
This function is disabled while time shift is on.
For more details about time shift, refer to Listen-
ing to a recent broadcast (time shift) on page 5.
Storing and recalling stations
for each band
Using preset tuning buttons
1 To store: Press and hold down one of the
preset tuning buttons (1/ to 6/ ) until
the number stops flashing.
2 To recall: Press one of the preset tuning
buttons (1/ to 6/ ).
Switching the display
Selecting the desired text information
1 Press DISP to cycle between the following:
! SERVICE LABEL (service label or channel)
! BRDCST INFO (service label/PTY label/en-
semble label/channel and frequency)
! DYNAMIC LABEL (dynamic label)
! CLOCK (source name and clock)
Notes
! If the service label cannot be acquired in
SERVICE LABEL, the channel is displayed in-
stead. If the service label is detected, the
service label will be displayed.
! For more details about PTY list, refer to PTY
list on page 6.