Recommendations On How To Use Desk Control; Disposal Of Linak's Products; Main Groups Of Disposal; Disposal Of Batteries - Linak DESKLINE XDLB-Serie Bedienungsanleitung

3. Recommendations on how to use Desk Control

Overriding a learned sedentary behaviour is a true behavioural challenge. We have put together a guide for how
to break up with your chair during your workday.
How to vary between standing and sitting while your work
The most important thing is to vary your position and to move around, preferably three times an hour. Instead
of sitting for too long at a time, you can switch between standing and sitting position. Remember good posture
and to stand with your body weight evenly distributed on both legs.
• Start by raising your desk and standing for 15 minutes each hour before you go to lunch.
• Just after lunch, stand for 15 minutes before lowering your desk to sit for 45 minutes.
• Raise your desk again every hour, so that you stand up working for 15 minutes each hour for the rest of the
day.
• Raise your desk before you leave for the day – then it is ready for the next day.
Important reservations when varying between standing and sitting position:
If you are pregnant, have varicose veins or have a health condition that may prevent you from standing for 5-15
minutes at a time every hour, you should contact your doctor to make sure that this will not be detrimental to
your health.

4. Disposal of LINAK's products

As LINAK's customers often ask us how our products can be disposed of or scrapped we have prepared this
guidance that enables a classification to different waste fractions for recycling or
combustion.
Guidance
We recommend that our products be disassembled as much as possible and divided into different waste groups
for recycling or combustion.
For example, waste can be sorted into metals, plastics, cable scrap, combustible material and recoverable
resources.
Some of these main groups can be further divided into subgroups; e.g. metal can be divided into steel/
aluminium/copper and plastic can be divided into ABS/PA/PE/PP.
As an example, the table below breaks down the different components in LINAK products to various recycling
groups:
Product Components
Handset/Control:
Plastic housing
Cable
PCB board
By now, almost all our casted plastic parts are supplied with an interior code for plastic type and fibre contents,
if any.

Main groups of disposal

Product main groups Metal scrap Cable scrap
Desk Control App
DPG
6/38
Recycling group
Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap
Electronics Plastic recycling or
scrap combustion
X X
X X X
EN 114065

Disposal of batteries

"Details regarding safe disposal of used and leaking batteries:
Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK
recommends that used or leaking batteries are disposed through local recycling system. Please do not throw
used or leaking batteries in normal household waste or in nature. This will cause damage to the enviroment.

How to deal with leaking batteries

Leaking batteries should be disposed as described above.
If leaking batteries are discovered in the product, the batteries must be removed at once to minimise damage to
the product.
If leaking batteries are left in the product, it become defective.
It is recommended to use plastic gloves when handling leaking batteries. The contents of a leaking batteries can
cause chemical burns and respiratory irritation.
If exposed to the contents of a leaking battery, please wash with soap and water. If irritation persists, please
seek medical attention. In case of eye contact, please flush eyes thoroughly with water for 15 minutes and seek
medical attention."

5. LINAK APPLICATION POLICY

The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK
product defined as hardware, software, technical advice, etc. related to an existing or new customer
application.
LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture,
Desk and Industry areas. Yet, LINAK cannot know all the conditions under which LINAK products will be
installed, used, and operated, as each individual application is unique.
The suitability and functionality of the LINAK product and its performance under varying conditions (application,
vibration, load, humidity, temperature, frequency, etc.) can only be verified by testing, and shall ultimately be
the responsibility of the LINAK customer using any LINAK product.
LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it
shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the
application in question.
iPod touch, iPhone, and iPad are trademarks of Apple Inc., registered in the U.S. and other countries.
"Made for iPod touch", "Made for iPhone," and "Made for iPad" mean that an electronic accessory has been
designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been certified by the
Comments
developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note that the use of this accessory with iPod touch,
iPhone or iPad may affect wireless performance.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Ascion,
LLC is under license. Other trademarks and trade names are those of their respective owners.
7/38 EN 114065