Statement - For All Intentional And Unintentional Radiators; Statement For Digital Devices For Class B; Labeling Requirements; Etl-Marking - Linak DESKLINE XDLB-Serie Bedienungsanleitung

Statement – for all intentional and unintentional radiators:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Statement for digital devices for Class B:

NOTE: This equipment has been tested and found to comply with the limits for a Class B diwgital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions it may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

Labeling Requirements:

This Class B digital apparatus complies with Canadian ICES-003.

ETL-marking

Due to space limitations, the complete ETL-marking demands are not represented on the
marking plates. The full ETL Recognized Component markings are
shown here.
C/N 120690
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component Zeichen für Kanada und Vereinigte Staaten
C/N 4008003
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component Zeichen für Kanada und Vereinigte Staaten
C/N 4008004
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component Zeichen für Kanada und Vereinigte Staaten
C/N 9901916
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component Zeichen für Kanada und Vereinigte Staaten
C/N 4008671
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component Zeichen für Kanada und Vereinigte Staaten
4/38 EN 114065

Only for EU markets

This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not
be made by children without supervision.

Only for Non EU markets

Persons who do not have the necessary experience or knowledge of the product/
products must not use the product/products. Besides, persons with reduced
physical, sensory or mental abilities must not use the product/products, unless
they are under surveillance or they have been thoroughly instructed in the use of the
apparatus by a person who is responsible for the safety of these persons.
Moreover, children must be under surveillance to ensure that they do not play with
the product.

Misuse

Do not overload the actuators – this can cause danger of personal injury and
damage to the system.
Do not use the actuator system for lifting persons. Do not sit or stand on a table
while operating – risk of personal injury.
Do not use the system in environments other than the intended indoor use

Repairs

In order to avoid the risk of malfunction, all DESKLINE
by authorised LINAK workshops or repairers, as special tools must be used and special
®
gaskets must be fitted. Lifting units under warranty must also be returned to authorised
LINAK workshops.
Warning!
If any of the DESKLINE products are opened, there will be a risk of subsequent
®
malfunction.
Warning!
The DESKLINE systems are not resistant to cutting oil.
®

Maintenance

Clean dust and dirt on the outside of the system at appropriate intervals and inspect for damage and
breaks.Inspect the connections, cables, and plugs and check for correct functioning as well as fixing
points.
The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).
5/38
repairs must only be carried out
®
EN 114065