janitza Power Analyser UMG 605-PRO Installationsanleitung Seite 13

L3 L3
L3 L3
Device settings for measurements
13 Device settings for measurements
13
S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2
S1 S2 S1 S2 S1 S2 3w 2u 3w 2u S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2
3w 2u 3w 2u
I I I I 17 L L The most important technical data L N L L I L I N I I I I
I 3 1 N I 2 I 3 I hv I 17 1 hv 2 L hv 3 L The most important technical data 1 hv L 2 1 N L 3 2 L I 3 L I 1 N I 2 I 3 2w 1m
3 2 3 1 2 3 1 2 3 1 2 1 3 2 3 1
The 4 voltage and current measurement inputs on
The 4 voltage and current measurement inputs on
the device are divided into inputs for the: the device are divided into inputs for the:
General
General
• baseline measurement (L1-L3 and I1-I3) and
• baseline measurement (L1-L3 and I1-I3) and
Net weight 350 g
Net weight
• supporting measurement (L4 and I4).
• supporting measurement (L4 and I4).
Approx. l = 107.5 mm,
Measured voltage and measured current for
Measured voltage and measured current for
b = 90 mm,
Device dimensions
Device dimensions
h = 82 mm
measurement inputs 1-4 must derive from the same
measurement inputs 1-4 must derive from the same
(nach DIN 43871:1992)
network. network.
Housing fl ammability class UL 94V-0
Housing fl ammability class
Type Lithium CR2032, 3V
Battery
Use measurement inputs L1-L3 and I1-I3 (baseline Battery
Use measurement inputs L1-L3 and I1-I3 (baseline
(according to UL 1642)
measurement) for three-phase network systems.
Installed position measurement) for three-phase network systems. any
Installed position
35 mm top hat rail
Fixing/mounting (according to IEC/EN 60999-1,
Fixing/mounting
In device address 110, you can choose between
In device address 110, you can choose between
DIN EN 50022)
14 different measurements for the baseline
14 different measurements for the baseline
40000h
Backlight lifetime
Backlight lifetime
(50% of initial brightness)
measurement (see the adjacent table and the measurement (see the adjacent table and the
diagrams in step 8).
diagrams in step 8).
Ambient conditions during operation Ambient conditions during operation
The device
The device
In device address 111, you can choose between In device address 111, you can choose between
• weather-protected and used stationary.
• weather-protected and used stationary.
the measurements for the supporting measurement. • fulfi lls conditions of use to DIN IEC 60721-3-3.
the measurements for the supporting measurement. • fulfi lls conditions of use to DIN IEC 60721-3-3.
• has protection class II according to IEC 60536 (VDE 0106, • has protection class II according to IEC 60536 (VDE 0106,
part 1). A PE terminal is not required!
part 1). A PE terminal is not required!
 
 
NOTE!
NOTE!
Operating temperature range Operating temperature range -10° C .. +55° C
For more settings, information and
For more settings, information and
5 to 95% at 25°C
Relative humidity Relative humidity
without condensation
diagrams on supporting measurement, diagrams on supporting measurement,
Operating altitude Operating altitude see the device's user manual. 0 .. 2000 m above sea level
see the device's user manual.
Degree of pollution 2
Degree of pollution
Ventilation No forced ventilation required.
Ventilation
Protection against ingress of IP20 according to EN 60529
Protection against ingress of
solid foreign bodies and water Sept. 2014, IEC 60529:2013
solid foreign bodies and water
Digital inputs
Digital inputs
2 digital inputs. 2 digital inputs.
Pulse input (S0):
Pulse input (S0):
Maximum counter frequency Maximum counter frequency 20 Hz
Switching input:
Switching input:
Response time (Jasic program) 200 ms
Response time (Jasic program)
18 V to 28 V DC
Input signal present
Input signal present
(typical 4 mA)
0 to 5 V DC,
Input signal not present
Input signal not present
current less than 0.5 mA
Digital outputs
Digital outputs
2 digital outputs, semiconductor relay, not short-circuit proof.
2 digital outputs, semiconductor relay, not short-circuit proof.
Switching voltage max. 30 V AC, 60 V DC
Switching voltage
Switching current max. 50 mAeff AC/DC
Switching current
Response time (Jasic program) Response time (Jasic program) 200 ms
Output of voltage dips 20 ms
Output of voltage dips
Output of
Output of
20 ms
voltage exceedance events
voltage exceedance events
Pulse output (energy pulse) max. 20 Hz
Pulse output (energy pulse)
Temperature measurement input Temperature measurement input
3-wire measurement.
3-wire measurement.
Update time approx 200 ms
Update time
Connectable sensors PT100, PT1000, KTY83, KTY84
Connectable sensors
Total burden (sensor + cable) max. 4 kOhm
Total burden (sensor + cable)
Cable length (Residual current monitoring, digital
Cable length (Residual current monitoring, digital
inputs and outputs, temperature measurement input)
inputs and outputs, temperature measurement input)
Up to 30 m Unshielded
Up to 30 m
More than 30 m Shielded
More than 30 m
L2
L2
N N
N N
S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2
S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2
L L L N L L I L I N I I I I L L
I I 1 2 2w 1m L 3 L 1 L 2 1 N L 3 2 L I 3 L I 1 N I 2 I 3 2w 2m I I 1 2 2w 2m
2 2w 1m 3 1 2 2w 1m 3 1 2 1 3 2 3 1 2 3 2w 2m
Device settings for "baseline measurement" Device settings for "baseline measurement"
Measurement
Transport and storage Transport and storage
Addr. Content
Addr. Content
The following information applies to devices which are transported (see step 8)
The following information applies to devices which are transported
350 g
or stored in the original packaging:
or stored in the original packaging:
0000 4w3m (standard setting)
0000
Approx. l = 107.5 mm,
Free fall
Free fall
b = 90 mm,
0001 4w2m
0001
Temperature
Temperature
h = 82 mm
(nach DIN 43871:1992)
0002 0002 4w2u
Supply voltage 230 V
Supply voltage
UL 94V-0
0003 4w2i
0003
Type Lithium CR2032, 3V
Protection of the
Protection of the
0004 3w3m
0004
(according to UL 1642)
supply voltage
supply voltage
any 0005 3w2m
0005
IEC -
Installation IEC
35 mm top hat rail Installation
0006 3w2u
0006
(according to IEC/EN 60999-1, overvoltage
overvoltage
110 110 IEC
IEC
300 V CAT II
DIN EN 50022) 300 V CAT II
category category 0007 3w2i
0007
UL
UL
40000h
0008 95 V - 240 V 2w2m
0008 95 V - 240 V
(50% of initial brightness)
(50/60 Hz) (50/60 Hz)
Nominal range
Nominal range 0009 2w1m
0009
or DC
135 V - 340 V
135 V - 340 V
0010 0010 4w3m_hv
Operating range +-10% of the nominal range
Operating range
0011 0011 4w2u_hv
Power consumption max. 3.2 W, max. 9 VA
Power consumption
0012 3w2u_hv
0012
0013 3w2m_hv
0013
-10° C .. +55° C
5 to 95% at 25°C
without condensation Device settings for "supporting measurement"
Device settings for "supporting measurement"
0 .. 2000 m above sea level
Addr. Content Measurement
Addr. Content Measurement
2
No forced ventilation required.
0000 2w1n (standard setting)
0000
IP20 according to EN 60529
Sept. 2014, IEC 60529:2013 111 0001 3w1m
111 0001
0002 4w1m
0002
RS232 interface
RS232 interface
5 pin screw-type terminals.
5 pin screw-type terminals.
Protocol Protocol Modbus RTU/slave
20 Hz
9.6 kbps, 19.2 kbps,
Transmission rate 38.4 kbps, 57.6 kbps,
Transmission rate
115.2 kbps.
200 ms
18 V to 28 V DC
RS485 interface
RS485 interface
(typical 4 mA)
2 pin screw-type terminals.
2 pin screw-type terminals.
0 to 5 V DC,
current less than 0.5 mA
Modbus RTU/slave,
Protocol
Protocol
Modbus RTU/master,
9.6 kbps, 19.2 kbps,
Transmission rate 38.4 kbps, 57.6 kbps,
Transmission rate
115.2 kbps, 921.6 kbps
max. 30 V AC, 60 V DC
max. 50 mAeff AC/DC
RS485 interface (optional)
RS485 interface (optional)
200 ms
Connector, SUB D 9 pin
Connector, SUB D 9 pin
20 ms
Profi bus DP/V0
Protocol, profi bus (optional)
Protocol, profi bus (optional)
20 ms according to EN 50170
Transmission rate 9.6 kbaud up to 12 Mbaud
max. 20 Hz Transmission rate
Ethernet interface 10/100Base-TX (optional)
Ethernet interface 10/100Base-TX (optional)
Connection RJ45
Connection
approx 200 ms
Modbus gateway,
Function
Function
PT100, PT1000, KTY83, KTY84 embedded Webserver (HTTP)
TCP/IP, EMAIL (SMTP),
max. 4 kOhm
DHCP-Client (BootP),
Modbus/TCP (Port 502),
Protocols
Protocols
Modbus RTU over Ethernet
(Port 8000), FTP, ICMP (Ping),
FTP, SNMP, NTP, TFTP.
Unshielded
Shielded
L2
L2
Confi gure the Ethernet connection
14
14
S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2
S1 S2 S1 S2 S1 S2 S1 S2 S1 S2 S1 S2
L N L L I L I N I I I I
L 3 L 1 L 2 1 N L 3 2 L I 3 L I 1 N I 2 I 3 I I
1 2 2w 2m 3 1 2 1 3 2 3 1 2 3
Static IP address (Addr. 205, content = 0)
In networks without a DHCP server, select the
Measurement
Voltage measurement
network address (see table) on the device.
(see step 8)
3-phase 4-conductor systems
with rated voltages (L-N/L-L)
4w3m (standard setting)
1 m
1 m BootP (Addr. 205, content = 1)
3-phase 3-conductor systems,
4w2m
-20° C to +70° C
-20° C to +70° C
BootP enables a UMG 605-PRO to be integrat- not earthed (L-L) with rated
4w2u voltages
ed into an existing network fully automatically.
90 V 24 V
230 V 90 V 24 V
Overvoltage category
However, BootP is an older protocol and does
4w2i
6 A, circuit breaker with
6 A, circuit breaker with
Measurement voltage surge
not provide the scope of functions provided by
tripping characteristic B 3w3m
tripping characteristic B
Protection of voltage
(IEC-/UL approval) (IEC-/UL approval) DHCP.
3w2m measurement
300 V CAT II -
- 300 V CAT II -
Resolution
3w2u
DHCP client (Addr. 205, content = 2)
- 150 V CAT II Crest factor
- 150 V CAT II
3w2i
DHCP makes it possible integrate a UMG 605-
Impedance
50 V - 110 V 20 V - 50 V
2w2m 50 V - 110 V 20 V - 50 V
PRO into an existing network automatically
Power consumption
(50/60 Hz) (50/60 Hz) (50/60 Hz) (50/60 Hz)
without the need for any additional confi gura-
2w1m
or DC or DC
or DC or DC or DC Sampling rate
50 V - 155 V 20 V - 70 V
50 V - 155 V 20 V - 70 V tion.
4w3m_hv Transients
+-10% of the nominal range When started, the UMG automatically obtains
Frequency of the mains
4w2u_hv
max. 5 W,
max. 5 W, frequency
the IP address, the subnet mask and the gate-
max. 3.2 W, max. 9 VA
max. 8 VA
3w2u_hv max. 8 VA - Resolution
way from the DHCP server. The default setting
3w2m_hv
for the UMG 605-PRO is "DHCP client".
Zeroconf (Addr. 205, content = 3)
Setting to confi gure the UMG 605-PRO using
the GridVis® software.
2w1n (standard setting)
3w1m
4w1m
Terminal connection capacity (supply voltage)
Connectable conductors. Connect one conductor per terminal!
Single core, multi-core,
Modbus RTU/slave
fi ne-stranded
9.6 kbps, 19.2 kbps,
Terminal pins, core end sheath
38.4 kbps, 57.6 kbps,
115.2 kbps.
Terminal connection capacity
(voltage and current measurement)
Connectable conductors. Connect one conductor per terminal!
Single core, multi-core,
Modbus RTU/slave,
fi ne-stranded
Modbus RTU/master,
Terminal pins, core end sheath
9.6 kbps, 19.2 kbps,
38.4 kbps, 57.6 kbps,
115.2 kbps, 921.6 kbps
Terminal connection capacity
(digital inputs and outputs (I/Os))
Connectable conductors. Connect one conductor per terminal!
Single core, multi-core,
fi ne-stranded
Profi bus DP/V0
according to EN 50170
Terminal pins, core end sheath
9.6 kbaud up to 12 Mbaud
Terminal connection capacity
(temperature measurement input)
Connectable conductors. Connect one conductor per terminal!
RJ45
Single core, multi-core,
Modbus gateway,
fi ne-stranded
embedded Webserver (HTTP)
Terminal pins, core end sheath
TCP/IP, EMAIL (SMTP),
DHCP-Client (BootP),
Modbus/TCP (Port 502),
Modbus RTU over Ethernet
(Port 8000), FTP, ICMP (Ping),
FTP, SNMP, NTP, TFTP.
13 / 14
Confi gure the Ethernet connection
Static IP address (Addr. 205, content = 0)
In networks without a DHCP server, select the
Current measurement
Voltage measurement
network address (see table) on the device.
Nominal current
3-phase 4-conductor systems
max. 277 V/480 V
max. 277 V/480 V
with rated voltages (L-N/L-L)
Rated current
BootP (Addr. 205, content = 1)
3-phase 3-conductor systems,
Protection of current
BootP enables a UMG 605-PRO to be integrat- max. 480 V
not earthed (L-L) with rated max. 480 V
measurement when measuring
voltages
directly
ed into an existing network fully automatically.
300 V CAT III (without a current transformer)
Overvoltage category 300 V CAT III
However, BootP is an older protocol and does
4 kV Crest factor
Measurement voltage surge 4 kV
not provide the scope of functions provided by
Resolution on the display
1 - 10 A
Protection of voltage 1 - 10 A
DHCP.
(with IEC-/UL approval)
measurement (with IEC-/UL approval)
Overvoltage category
0.01 V
Resolution 0.01 V Measurement voltage surge
DHCP client (Addr. 205, content = 2)
2 (based on 480 Vrms)
Crest factor 2 (based on 480 Vrms) Power consumption
DHCP makes it possible integrate a UMG 605-
4 MOhm / phase
Impedance 4 MOhm / phase
Overload for 1 sec.
PRO into an existing network automatically
approx. 0.1 VA
Power consumption approx. 0.1 VA
Sampling rate
without the need for any additional confi gura-
20 kHz / phase
Sampling rate 20 kHz / phase
tion.
>50 µs
Transients >50 µs
When started, the UMG automatically obtains
Frequency of the mains
15 Hz to 440 Hz
the IP address, the subnet mask and the gate- frequency 15 Hz to 440 Hz
0.001 Hz
- Resolution 0.001 Hz
way from the DHCP server. The default setting
for the UMG 605-PRO is "DHCP client".
Zeroconf (Addr. 205, content = 3)
Setting to confi gure the UMG 605-PRO using
the GridVis® software.
Terminal connection capacity (supply voltage)
Connectable conductors. Connect one conductor per terminal!
Single core, multi-core,
0.08 - 2.5 mm , AWG 28-12
0.08 - 2.5 mm 2 , AWG 28-12
2
fi ne-stranded
1.5 mm AWG 16
Terminal pins, core end sheath 2, 1.5 mm AWG 16
2,
Terminal connection capacity
(voltage and current measurement)
Connectable conductors. Connect one conductor per terminal!
Single core, multi-core,
0.08 - 4 mm 2 , AWG 28-12
0.08 - 4 mm 2 , AWG 28-12
fi ne-stranded
2.5 mm 2 , AWG 14
Terminal pins, core end sheath 2.5 mm 2 , AWG 14
Terminal connection capacity
(digital inputs and outputs (I/Os))
Connectable conductors. Connect one conductor per terminal!
Single core, multi-core,
0.08 - 1.5 mm
0.08 - 1.5 mm 2 2
fi ne-stranded
1 mm
Terminal pins, core end sheath 2 1 mm 2
Terminal connection capacity
(temperature measurement input)
Connectable conductors. Connect one conductor per terminal!
Single core, multi-core,
0.08 - 1.5 mm 0.08 - 1.5 mm 2
2
fi ne-stranded
Terminal pins, core end sheath 1 mm 2 1 mm
2
Addr. Designation
Addr. Designation
Current measurement
RS485, Modus
RS485, Modus
5 A
Nominal current 5 A
0 = Modbus RTU/Slave
0 = Modbus RTU/Slave
203
203
6 A
Rated current 6 A
1 = Modbus RTU/Master
1 = Modbus RTU/Master
Protection of current
2 = Gateway-Transparent
2 = Gateway-Transparent
6 A, char. B
measurement when measuring 6 A, char. B
RS232, mode (approved i.a.w. UL/IEC)
directly RS232, mode (approved i.a.w. UL/IEC)
(without a current transformer)
0 = Modbus RTU/slave
0 = Modbus RTU/slave
204
204
2 (based on 6 Amps)
Crest factor 2 (based on 6 Amps)
(default setting)
(default setting)
10 mA
Resolution on the display 10 mA
3 = Debug 6 = SLIP
3 = Debug 6 = SLIP
300 V CAT III
Overvoltage category 300 V CAT III
DHCP mode
DHCP mode
4 kV
Measurement voltage surge 4 kV
205 205 0 = static IP address 1 = BootP 0 = static IP address 1 = BootP
approx. 0.2 VA (Ri = 5 mOhm)
Power consumption approx. 0.2 VA (Ri = 5 mOhm)
2 = DHCP client 3 = Zeroconf
2 = DHCP client 3 = Zeroconf
100 A (sinusoidal)
Overload for 1 sec. 100 A (sinusoidal)
300 IP address, xxx --- --- ---
300 IP address, xxx --- --- ---
20 kHz
Sampling rate 20 kHz
301 IP address, --- xxx --- ---
301 IP address, --- xxx --- ---
302 IP address, --- --- xxx ---
302 IP address, --- --- xxx ---
303 IP address, --- --- --- xxx
303 IP address, --- --- --- xxx
304 IP mask, xxx --- --- ---
304 IP mask, xxx --- --- ---
305 305 IP mask, IP mask, --- xxx --- --- --- xxx --- ---
306 306 IP mask, IP mask, --- --- xxx --- --- --- xxx ---
307 IP mask, --- --- --- xxx
307 IP mask, --- --- --- xxx
310 IP gateway, xxx --- --- ---
310 IP gateway, xxx --- --- ---
311 IP gateway, --- xxx --- ---
311 IP gateway, --- xxx --- ---
312 IP gateway, --- --- xxx ---
312 IP gateway, --- --- xxx ---
313 IP gateway, --- --- --- xxx
313 IP gateway, --- --- --- xxx
 
 
NOTE!
NOTE!
Further technical data can be found in Further technical data can be found in
the user manual for the device.
the user manual for the device.