Technical Data; Before Starting - EINHELL 34.111.30 Originalbetriebsanleitung

Anleitung_RG_CT_18_Li_SPK7:_
GB

4. Technical data

Speed n :
0
Cutting range:
Max. running period:
Type of protection:
Sound power level L :
WA
Sound pressure level L :
pA
Replaceable NC battery:
Front handle vibration a :
hv
Rear handle vibration a :
hv
Weight
Power supply unit:
Mains voltage:
Output:
Rated voltage:
Rated current:
The noise level of this machine may exceed 85
dB(A). In this case, noise protection is necessary for
the user. The machine's noise was measured in
accordance with prEN ISO 10518. The level of
vibrations at the handle is < 2,5 m/s
were taken in accordance with prEN ISO 10518.

5. Before starting

5.1 Installing the safety hood (Fig. 4-7)
Secure the edge guide to the safety hood (Fig. 4-
5) using the two securing screws (Fig. 2/Item 13).
Place the safety hood on the trimmer (Fig. 6) and
secure to the trimmer (Fig. 7) it using the four
securing screws (Fig. 2 / Item 12).
5.2 Installing the additional handle (Fig. 9-10)
Undo the securing screw from the handle and
then place the handle on the main handle (Fig. 9)
and secure it with the screw (Fig. 1).
5.3 Fitting the blade (Fig. 11-12)
Place the blade (Fig. 11/Item 14) with the larger
opening over the mount (Fig. 11) and then pull tight
in the direction of the arrow. Make sure the blade
locks into place correctly as shown in Figure 12.
12
18.01.2010 10:06 Uhr
5.4 Height adjustment (Fig. 13)
Undo the union nut (Fig. 13/Item 5) until the grass
trimmer handle can be moved in and out freely. Now
8500 min -1
set the required working height and secure the handle
in this position by tightening the union nut again.
24 cm diameter
approx. 35 min
5.5 Adjusting the additional handle (Fig. 10)
III
Undo the securing screw on the additional handle
until it can be moved forwards and backwards without
94 dB(A)
any great resistance. Set the required position and
77 dB(A)
tighten the securing screw again.
18 V d.c./1400 mAh
5.6 Adjusting the angle of the guide handle
≤ 2,5 m/s 2
(Fig. 14)
≤ 2,5 m/s 2
Place the grass trimmer on a firm surface. Press the
2.8 kg pedal for adjusting the angle from above using your
foot (Fig. 14/Item 9). You can now set the handle to
the required angle. Release the pedal and allow the
handle to lock into position to fix the angle. Three
230 V ~ 50 Hz different locking angles are possible.
5.7 Charging the battery (Fig. 15 – 17)
1. Take the battery pack out of the equipment.
Press the locking buttons on the side to release
21 V d.c.
the battery pack (Fig. 15-16).
500 mA
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Connect the charger's power cable to a
socket outlet and insert the plug (Fig. 17/Item C)
into the charging jack of the battery pack. The
red LED indicates the charging process.
2 . Measurements
3. The charger will end the charging process
automatically when the battery is fully charged
(after approx. 3-5 h). The green LED will come
on.
The rechargeable battery can become a little warm
during the charging process. This is normal.
When you insert the battery again ensure that it locks
securely in the mounting Fig. 16 /Item B) with the
opening at the rear (Fig. 16 / Item A).
If the battery pack fails to charge, please check
whether there is voltage at the socket-outlet
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
the battery charger with charging adapter
and the battery pack
to our customer services department.
Seite 12