Eca 150 Ipro Vzc, Eca 150 Ipro; Kvzc; Eca 150 Ipro B, Eca 150 Ipro Kb; Eca 150 Ipro H, Eca 150 Ipro Kh - Maico ECA 150 ipro Montage- Und Betriebsanleitung

5 Product information

5.2 ECA 150 ipro VZC, ECA 150 ipro

KVZC

• Small room fans for extracting air from rooms.
• Model with adjustable start delay and overrun
time.
• ECA 150 ipro VZC with fixed internal grille.
• ECA 150 ipro KVZC with electrically operated
internal shutter.
• Two power levels as standard. Operation in
either level 1 or level 2.
• On/off with light switch or separate switch.
• Further product features → Unit versions
[} 25].

5.3 ECA 150 ipro B, ECA 150 ipro KB

• Small room fans for extracting air from rooms.
• Model with motion detector and overrun time.
No start delay.
• ECA 150 ipro B with fixed internal grille.
• ECA 150 ipro KB with electrically operated in-
ternal shutter.
• Barrier-free product as the fan switches itself on
and off via the motion sensor.
• Motion sensor range 5 m, horizontal monitoring
range 100°, vertical monitoring range 82°.
• Two power levels as standard. Operation in
either level 1 or level 2.
• Operation possible without switch. Can option-
ally also be switched via separate switch.
• Further product features → Unit versions
[} 25].

5.4 ECA 150 ipro H, ECA 150 ipro KH

• Small room fans for extracting air from rooms.
• Model with humidity control (fully automatic),
start delay and overrun time.
• ECA 150 ipro H with fixed internal grille.
• ECA 150 ipro KH with electrically operated in-
ternal shutter.
• Barrier-free product as the fan switches itself on
and off via the humidity sensor.
• Switch-on humidity does not have to be set.
Fan monitors the room humidity.
• 2 performance levels as a standard feature.
Fan extracts air automatically in level 1 or level
2, depending on the room humidity.
• Operation possible without switch. Can option-
ally also be switched via separate switch.
24
• Further product features → Unit versions
[} 25].
Automatic humidity function
Once the fan is installed, it adjusts to the room
humidity prevailing at that time (relative humidity).
This humidity value is saved as the first reference
value. The reference value does not have to be
specified manually.
If the relative humidity falls below the reference
value during operation, the newly established ref-
erence value is saved. The lowest possible refer-
ence value is 48 % relative humidity.
When the room humidity increases
• If the room humidity increases by 7%, the fan
switches on automatically at power level 1 (200
m³/h).
• If the humidity increases even further, the unit
switches to power level 2 (250 m³/h).
• If there are no further increases, the fan contin-
ues to run at power level 1 (200 m³/h) until the
humidity again falls below the saved reference
value.
When falling below the reference value
• H and KH: Overrun operation starts with the set
overrun time. The current reference value is
then saved.
• RCH and KRCH: No overrun operation.
Value does not fall below reference value for 1
hour
• H and KH: Overrun operation starts. Fan then
switches off.
• RCH and KRCH: Fan switches off.
Operation using light and/or radio switch
• H and KH units can also be operated using the
light switch. With "Light on", the set operating
programme starts with the start delay → Oper-
ating programs [} 30] The operating program
takes priority over the automatic humidity func-
tion. After switching off, the unit continues to
run until the remaining overrun time has
passed. The automatic humidity function is then
assigned maximum priority again and controls
the unit as described above.
• Optionally, RCH/KRCH units can be operated
in 2 levels using a radio switch. Switching
through the DS RC or window contact is pos-
sible during humidity operating mode.