Daily Use - Whirlpool WT 1090 BA Bedienungsanleitung

DAILY USE

PAN DETECTOR
Induction cooking zones have a built-in pan detector. This way, the plate will
stop working if there is no pan present or if the pan is not suitable.
The power indicator (3) will show a symbol to designate "there is no pan
if, while the zone is on, no pan is detected or the pan is not suitable.
If a pan is taken off the zone while it is running, the plate will automatically
stop supplying energy and it will show the symbol for "there is no pan". When
a pan is once again placed on the cooking zone, energy supply will resume at
the same power level previously selected.
CONTROL PANEL LOCK
With the Block Function, you can block the other sensors, except for the on/
off sensor (1), in order to avoid undesired operations. This function
is useful as a childproof safety.
To activate this function, touch sensor
Once you have done so, the pilot (7) turns on indicating that the control
panel is blocked. To deactivate the function, simply touch sensor
again.
If the on/off sensor (1) is used to turn off the appliance while the
block function is activated, it won't be possible to turn the cooktop on again
until it unblocks.
SILENCER OF THE BEEP
When the hob is on, if one presses the touch key
key (6) simultaneously for three seconds, the beep that accompanies
each action will be deactivated. The time indicator (12) will display "OF". This
deactivation will not be applied to all the functions, as for example the
beep for on/off, the ending of the timer or the locking/unlocking of the touch
keys always remain activated.
To once again activate all the beeps that accompany each action, again
simultaneously press the touch key
(6) for three seconds. The time indicator (12) will display "On".
STOP&GO FUNCTION
This function puts the cooking process on pause. The timer will also be paused
if it is activated.
Activating the Stop function.
Touch the Stop sensor (8) for one second. The pilot (9) lights up and
the power indicators will show the symbol
paused.
Deactivating the Stop function
Touch Stop&Go sensor
cooking resumes under the same power and timer settings that were
established before the pause.
POWER FUNCTION
This function supplies "extra" power to the plate, above the nominal value.
Said power depends on the size of the plate, with the possibility of reaching
the maximum value permitted by the generator.
1. Slide the finger above the corresponding cursor slider (2) until the power
indicator (3) shows "9" and keep the finger pressed for one second, or
touch directly on "P" and keep pressed the finger for one second.
2. The power level indicator (3) will show the symbol
start to supply extra power. The Power function has a maximum duration
specified in Table 1. After this time, the power level will automatically
adjust to 9. A beep sounds.
(6) for at least one second.
(11) and the locking touch
(11) and the locking touch key
to indicate cooking has been
(8) again. The pilot (9) turns off and
, and the plate will
On activating the Power function in one hotplate, it is possible that the
performance of some of the others may be affected, reducing its power to a
lower level, in which case this will be displayed on its indicator (3).
Deactivation of Power Function, before it's working time passes, can be
"
done either by means of touching cursor "slider" modifying its power level or
repeating step 3.
TIMER FUNCTION (countdown clock)
This function facilitates cooking given that you don't have to be present: You
can set a timer for a plate, and it will turn off once the desired time is up.
For these models, you can simultaneously program each plate for durations
ranging from 1 to 99 minutes.
Setting a timer on a plate.
Once the power level is set on the desired zone, and while the decimal dot of
the zone keeps on, the zone will be able to be timed.
(6)
To that end:
1. Touch sensor
corresponding zone indicator (3) will show the symbol blinking alternately
with its current power level.
2. Immediately afterwards set a cooking time between 1 and 99 minutes,
using the sensors
start at 60, whereas with the second it will start at 01. To cancel the timer
function, the clock can be adjusted to value '00' using sensor
quicker way to do this is keeping sensors
together. When there is less than one minute left, the clock will begin to
countdown in seconds.
3. When the timer indicator (12) stops flashing, it will start to countdown the
time automatically. The indicator (3) relating to the timed hotplate will
alternately display the selected power level and the symbol
Once the selected cooking time has elapsed, the heating zone being timed
is turned off and the clock emits a series of beeps for several seconds. To turn
off the audible signal, touch any sensor. The timer indicator (12) will display a
flashing 00 beside the decimal dot (4) of the selected zone. If the heating zone
turned off is hot, its power indicator (3) will display alternately the H symbol
and a "-".
If you wish to time another hotplate at the same time, repeat steps 1 to 3.
If one or more zones are already timed, the timer indicator (12) will show by
default the shortest remaining time to finish, showing a "t" on the related
zone. Rest of timed zones will show on their corresponding indicator zones
the decimal dot blinking. When the cursor "slider" of another timed zone is
pressed, the timer will show the remaining time of that zone for a few seconds
and its indicator will show its power level and the "t" alternately.
Changing the programmed time
For modifying programmed time, the cursor "slider" (2) of the timed zone has
to be pressed. Then it will be possible to read and modify the time.
Through sensors
Disconnecting the clock
If you wish to stop the clock before the programmed time is up, this can be
done at any time by simply adjusting its value to '--'.
1. Select the desired plate.
2. Adjust the value of the clock to "00" by using the sensor
is cancelled. This can also be done more quickly by pushing the "sensors
(10) and
(10) or (11). Timer Indicator (12) will show "00" and
(10) or (11). With the first one the value will
(10) and (11), you can modify the programmed time.
(11) at the same time.
(10). A
(10) and (11) pressed
.
(10). The clock