Herunterladen Inhalt Inhalt Diese Seite drucken

Kinderkraft NEA Bedienungsanleitung Seite 30

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 23
The canopy (8) is attached to the seat frame. You can zip the additional panel onto the canopy (11). To remove the canopy,
undo the zip (Fig.V) and the snaps on the sides of the seat. Now pull the canopy on both sides of the frame, as shown in
Fig.W. To refit the canopy, repeat the actions in reverse order. The canopy can be adjusted in several positions (Fig.X).
V.IV ARMBAR
Push the armbar onto each side of the frame until it locks into position (Fig.Y). In order to detach the armbar, push the
buttons on both sides of the frame and remove it (Fig.I).
V.V SAFETY BELTS
Safety belts (9) need to be adjusted each time to ensure proper protection of the baby.
To secure your child, slide the hip and shoulder straps into the centre buckle until they engage (Fig.Z). Push the button on
the buckle to unfasten the safety belts (Fig.AA). Safety belts can be fitted/removed. To remove the safety belts insert the
shoulder straps and hip straps through the holes in the seat backrest and pull up the crotch strap. Next, undo the zip on the
back of the seat and insert the shoulder straps and hip straps through the holes (Fig.BB). Before you insert the crotch strap
through the hole, remove the seat liner, as shown in (Fig.CC). To fit the belts, repeat the steps in reverse order. The shoulder
belts can be fitted on one of the three heights and the crotch strap can be fitted on one of the two heights. Make sure that
the buckles holding the belts are locked properly.
VI SEAT POSITIONS
The seat can be set in 4 positions: 1 recumbent, 2 semi-recumbent, and 1 seated; the positions can be adjusted with the
backrest adjustment lever (Fig.DD).
VII ADJUSTING THE FOOTREST
You can set the footrest in one of the three positions. Press the buttons on both sides of the footrest simultaneously and
set the footrest in the desired position (Fig.EE). Additionally, you can push the footrest fabric liner up in order to lift the
footrest (Fig.FF).
VIII ADJUSTING THE HANDLE
To adjust the handle, push the button in the centre and set the handle in a comfortable position. You can adjust the height
of the handle to one of the 4 levels (Fig.GG).
IX ASSEMBLING THE CUP HOLDER, MOSQUITO NET AND THE TRANSPARENT RAIN COVER
Fit the cup holder to the shank on the right hand side of the stroller.
Place the mosquito net over the seat (Fig.HH). The elastic band inside the edge will keep the net in the position.
Place the rain cover over the stroller and secure it using the button and eye under the stroller frame on its both sides (Fig.II).
X FOLDING THE STROLLER
When you use the stroller with the car seat or with the pram body, first remove these elements from the frame.
Detach the additional canopy (11) by using the zip (as shown in V.III). Fold the canopy. Fold the backrest flat toward s the
seat by pulling the adjustment lever. Now press the button and pull up both levers of the frame (Fig.JJ) handle down whilst
pulling the front wheels to the rear wheels until the 'click' is heard. When the stroller is folded, the locking mechanism will
activate automatically (Fig.KK). You can remove the wheels to reduce the size of the folded stroller. The stroller can be
folded with the seat attached to it in the forward facing position or in the rearward facing position. When folded, the stroller
is in the upright position, therefore the front wheels need to be locked so that the stroller cannot move forward; the handle
has to be kept in its lowest position.
XI REMOVING THE SEAT COVER
The seat cover can be removed and washed. Detach the canopy first by following the instructions in V.III. Remove the
armbar, unfasten the velcro strips under the seat and then unzip the zip on the rear side of the backrest. Now detach the
safety belts (as shown in V.V), pull the seat cover out of the frame and remove the insert.
XII. ASSEMBLING THE CAR SEAT ON THE STROLLER FRAME
Adapters are compatible with the following car seats: Kinderkraft®, Kiddy®, Maxi Cosi®, Cybex®, BeSafe®, Nuna® and fit e.g.
with the models: Kinderkraft MINK, Kinderkraft i-Care, Kiddy Evoluna I-Size 2, Evolution Pro 2, Cybex Aton, Aton 2, Aton Q,
Maxi Cosi Mico, Mico AP, Mico NXT, Mico Max 30, Citi, Cabrio, CabrioFix, BeSafe iZi Go, iZi Go Modular, Nuna Pipa. Click the
right (R) and left (L) adapters (19) into both sides of the frame (Fig.LL). To attach the car seat to the adapters, click the car
seat into the buckles, one for each side of the stroller until you hear a distinctive clock (Fig.MM). To remove the adapters,
press the buttons on both sides and pull up (Fig.NN).
NOTE! The car seat must always be fitted in such a way that the
child should face the carer.
XIII CARE AND MAINTENANCE The buyer is responsible for proper installation of all functional elements as well as for
carrying out all required maintenance and adjustments in order to keep the buggy in good technical condition.
The buggy must be periodically checked for potential problems. Significant measures to be applied to ensure the child's
safety and prevent shortening of the product life have been presented below:
• Check the strength and safety of all rivets and connections.
• Check all wheel locking equipment and tyres. If necessary, replace or repair.
30

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis