Using The Brake - Kinderkraft NEA Bedienungsanleitung

I STROLLER PARTS
1. Frame with basket (2)
4. Pram body
6. Leg cover
10. Additional panel for canopy (pram body)
12. Armbar
14. Front wheel x2
16. Transparent rain cover
18. Cup holder
II UNFOLDING THE FRAME
Stand the frame (1) with basket (2) on a flat surface, handle up. Press the lock button on the frame to unlock it (Fig.A.I) and
pull up both levers simultaneously (Fig.A.II). Lift the handle and unfold the frame until it locks into position (Fig.B). Push the
rear axle onto the frame until it clicks (Fig.C).
III ASSEMBLING/DETACHING THE WHEELS
Click the front wheels (14) into the holes in the front part of the frame (Fig.D.I). Press the release button to remove the front
wheels. The stroller is equipped with swivel front wheels which can be locked to move forward only. Pull the blocking lever
up/down to unlock the swivel wheels (Fig.D.III). Insert the rear wheels (13) into the holes on the rear axle of the frame until
they are locked completely. Make sure the flat surfaces of the axle and the hole are set properly (Fig.E.IV). Push the release
button and pull the rear wheel to remove it (Fig.E.V).
NOTE! Before using the buggy make sure that all the wheels are
properly installed.
IV. USING THE BRAKE
The stroller is equipped with a foot parking brake. Step on the brake. When the locking sound is heard, the brake is activated
(Fig.F). You can release the brake by lifting the lock.
V ASSEMBLY/DISASSEMBLY
V.I PRAM BODY
Stand the pram body (4) on a flat surface. To unfold the pram body, remove the leg cover and the mattress inside it and
then pull the tape to fit the front bar until it is locked. Repeat these steps in order to fit the rear bar (Fig.G). Attach the
additional panel (10) to the canopy with the zip (Fig.H). Place the mattress (5) inside the pram body.
Place the so prepared pram body on the frame (Fig.I). Make sure the fasteners on both sides are locked. In order to remove
the pram body, press the release buttons on both sides simultaneously (Fig.J).
Repeat these actions in reverse to fold the pram body.
NOTE! THE PRAM BODY CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
NOTE! Do not fold the buggy frame when the Pram body is
installed on it.
Set the canopy in a desired position with the use of folding and unfolding buttons on both sides of the pram body (Fig.K).
You can use the zip on the canopy in order to extend it. The pram body has an additional ventilated panel at the front. To
open the panel unzip the zip and pull down the cloth (Fig.L). The second ventilation panel is placed on the canopy. To open
the second panel, unzip the zip and roll up the cloth (Fig.M). Fit the leg cover by using the zips. Both zip fasteners have to
be on the right hand side. Move the lower fastener along the body to close the cover (Fig.N). The leg cover is equipped with
an additional windproof panel which can be fitted with the use of snaps inside the pram body. Place the transparent rain
cover over the body and secure it on both sides with the button and eye under the frame (Fig.O). The mosquito net should
be placed over the pram body (Fig.P).
V.II SEAT
Place the seat (7) onto the frame until it clicks (Fig.Q). The seat can be attached in the forward facing position or in the
rearward facing position (Fig.R). To remove the seat, press the buttons on both sides and pull up (Fig.S). To fit the cover,
just remove the armbar (12) following the instructions in V.IV and then insert it through the holes in the cover (Fig.T). Next,
locate the armbar in the right position into the seat frame (Fig.U). Use the button to fit the cover to the sides of the frame
with the eye.
V.III CANOPY
NOTE! Install the canopy before using the buggy.
3. Rear axle
5. Pram body mattress
7. Seat with canopy (8) and safety belts (9)
11. Additional panel for canopy (stroller)
13. Rear wheel x2
15. Leg cover for stroller
17. Mosquito net
19. Adapters
29