Seite 1
PR Series Balances Instruction Manual Balanzas Serie PR Manual de Instrucciones Balance de Sé ries PR Manuel d’instruction PR Serie Waagen Bedienungsanleitung Bilance Serie PR Manuale di Istruzioni...
PR Series Balance EN-1 Table of Contents 1. INTRODUCTION ......................EN-3 Description ............................. EN-3 Features ..............................EN-3 Definition of Signal Warnings and Symbols ................... EN-3 Safety Precautions ..........................EN-3 2. INSTALLATION ....................... EN-4 Unpacking .............................. EN-4 Select the Location ..........................EN-4 Leveling ..............................
Seite 4
EN-2 PR Series Balance 5.6.9 User Name ............................EN-24 5.6.10 Project Name ........................... EN-24 5.6.11 Application Name ..........................EN-24 5.6.12 Result ............................... EN-24 5.6.13 Gross ..............................EN-24 5.6.14 Net..............................EN-25 5.6.15 Tare..............................EN-25 5.6.16 Line Feed ............................EN-25 GLP ..............................
PR Series Balance EN-3 1. INTRODUCTION 1.1 Description The PR balance is a precision weighing instrument that will provide you with years of service if properly cared for. PR balances are available in capacities from 62 grams to 6200 grams. 1.2 Features Operation Controls: backlit display, with 3 weighing applications and many features.
EN-4 PR Series Balance 2. INSTALLATION 2.1 Unpacking Carefully remove your PR balance and each of its components from the package. The included components vary depending on the balance model. Save the packaging to ensure safe storage and transport. Please read the manual completely before installing and using the PR balance to avoid incorrect operation.
PR Series Balance EN-5 Connecting the Interface The PR balance has a RS232 port. Use the RS-232 port to connect either to a computer or a printer with a standard (straight-through) serial cable. Interface connections on the rear of the balance RS232 RS232:Used to connect to PC or Printer Note: See the Printing section for Connecting, Configuring and Testing the Printer / Computer Interface.
EN-6 PR Series Balance 3. OPERATION Overview of Controls and Display CONTROLS CONTROL FUNCTIONS Button On / Zero Print Function Tare Primary Function If the balance is Off, Sends the current Operation is Performs tare (Short turns on the displayed value to dependent on the...
PR Series Balance EN-7 MAIN APPLICATION SCREEN Result Field: depending on Net (NET) application Stability (*) Negative (-) Centre of zero (>0<) Unit Pre-tare (PT) Principal Functions Weighing: First press Zero to set the display to zero. Place an object on the pan. The display indicates the gross weight.
EN-8 PR Series Balance 4. APPLICATIONS The PR balance can be operated in 3 application modes by long pressing the Function / Mode button. Weighing Note: Before using any application, be sure the balance has been leveled and calibrated. Use this application to determine the weight of items in the selected unit of measure. Weighing 1.
Seite 11
PR Series Balance EN-9 3. After confirmation by pressing Yes, the message Clr.APwj will appear on the screen. 4. Press Yes, and the message Put10 will display with the numeral 10 (default) flashing. The user can press No or Back to increase or decrease the value. For instance, to increase the value to 15, please press No.
EN-10 PR Series Balance Item Settings To view or adjust the current settings. Sample size: The sample size ranges from 1 to 100. The default value is 10. Note: If the APW of the last parts counting operation needs to be kept, the user can press No when the display shows the message Clr.Apwj (clear the average piece weight.
Seite 13
PR Series Balance EN-11 3. Press Yes, and PUt.ref (put the reference weight) will display. 4. Place the reference sample on the pan to display the weight. When the reading is stable, the * appears. 5. Press the Function / Mode button so that the weight of the reference sample is stored in memory.
EN-12 PR Series Balance Printing Setup: Changing printing setup. See Section 7 for more information. Additional Features Weigh Below Note: Ensure the balance has been leveled and calibrated. The PR balance is equipped with a weigh below hook for weighing below the balance (as shown below). Before turning the balance over, remove the pan and draft shield elements (if present) to prevent damage.
PR Series Balance EN-13 5. MENU SETTINGS 5.1 Menu Navigation Calibration Setup Unit RS232 Print Reset Lock InCal Filter Level Gram Baud Rate Stable Only Header 1 Reset All Calibration Cal Adjust Kilogram Parity Numeric Only Header 2 Setup Span Cal Auto Tare Milligram Handshake...
EN-14 PR Series Balance 5.2 Calibration PR balances offer a choice of three calibration methods: Internal Calibration (for InCal models only), Span calibration and Linearity Calibration. Attention: Do not disturb the balance during any calibration. 5.2.1 Calibration Sub-menu (InCal models) Note: ExCal models only have Span Calibration and Linearity Calibration.
PR Series Balance EN-15 With the balance turned On and no load on the pan, Span Calibration can be performed. The best accuracy is achieved using the mass closest to the full span value. Steps for span calibration 1. Press and hold the Tare / Menu-Cal button, and the Calibration Menu will display.
Seite 18
EN-16 PR Series Balance With no load on the balance, press Linearity Calibration to begin the process. The balance captures the zero point, and then prompts for the next weight. Steps for linearity calibration Continue to follow the instructions on the display until the calibration is completed. 1.
PR Series Balance EN-17 5.3 Balance Setup Enter this sub-menu to customize the balance functionality. Note: The factory default settings are shown below in bold. 5.3.1 Filter Level Set the amount of signal filtering. FiltEr = faster stabilization time with less stability. Medium = normal stabilization time with normal stability.
EN-18 PR Series Balance 5.3.4 Graduations Set the displayed readability of the balance. 1 Division = standard readability. 10 Divisions = readability is increased by a factor of 10. For example, if the standard readability is 0.01 g, selecting 10 Divisions will result in a reading of 0.1 g. GrAd 10 d Graduation...
PR Series Balance EN-19 5.3.8 Time Setup Set the current time in the desired time format. timME To set the current time, press No or Back to increase or decrease the 08.00.00 value. 5.3.9 Brightness Set the brightness of the display. bright mMEd Medium...
EN-20 PR Series Balance 5.3.11 Approved Mode Use this menu to set the Legal for Trade status. = standard operation. = operation complies with Legal Metrology regulations. For PRxxxN models: Use this menu to set the Legal for Trade status. = standard operation.
PR Series Balance EN-21 Changing Weighing Units 1. Press and hold the Print / Unit button until the Unit Menu is displayed. 2. The default unit is gram (g). To change the unit, press No to advance to the next unit. 3.
EN-22 PR Series Balance 5.5.2 Transmission Set the data bits, stop bit, and parity. 8-N-1 = 8 data bits, no parity, stop bit 1 8-N-2 = 8 data bits, no parity, stop bit 2 7-E-1 = 7 data bits, even parity, stop bit 1 7-E-2 = 7 data bits, even parity, stop bit 2 7-N-1 = 7 data bits, no parity, stop bit 1 7-N-2 = 7 data bits, no parity, stop bit 2...
PR Series Balance EN-23 5.6.2 Numeric Only Off = All results selected are printed. NumM On = Only numeric data values are printed. 5.6.3 Single Header Off = Headers will be printed for every print requirement. Sin.Head On = Headers will be printed once a day. 5.6.4 Auto Print Enable or disable the functionality of auto print, and set the specific A.Print...
EN-24 PR Series Balance 5.6.5 Header On = the header is printed. Header Off = the header is not printed. 5.6.6 Date and Time On = the date and the time are printed. dtmM Off = neither the date nor the time is printed. 5.6.7 Balance ID On = the balance ID is printed.
PR Series Balance EN-25 5.6.13 Gross On = the gross weight is printed. GrosS Off = the gross weight is not printed. 5.6.14 Net On = the net weight is printed. Off = the net weight is not printed. 5.6.15 Tare On = the tare weight is printed.
EN-26 PR Series Balance 5.7.2 Balance Name Set the balance name. Bal.NamM Alphanumeric settings up to 16 characters are available for each Header setting. 5.7.3 User Name Set the user name. Usr.NamM Alphanumeric settings up to 16 characters are available for each Header setting.
PR Series Balance EN-27 6. LEGAL FOR TRADE(LFT) When the balance is used in trade or a legally controlled application it must be set up, verified and sealed in accordance with local weights and measures regulations. It is the responsibility of the purchaser to ensure that all pertinent legal requirements are met.
EN-28 PR Series Balance 6.3 Sealing After the Balance has been verified, it must be sealed to prevent undetected access to the legally controlled settings. Before sealing the device, ensure the Approved Mode setting in the Balance Setup menu has been set to ...
Use RS232 Interface Commands (Section 9.6.1) to control the balance from a PC. SPDC Software The Serial Port Data Collection / SPDC software is provided by Ohaus and can be used on operating systems that do not have the HyperTerminal software mentioned above. SPDC software can preliminarily collect and transfer the data to Microsoft files (such as Excel, Word, etc.).
EN-30 PR Series Balance Output format The Result Data, and G/N/T data, is output in the following format. Term. Field: Label Space Weight Space Unit Space Stability Space Space Characters 1 1 3 8 Length: Note: 1.
Seite 33
PR Series Balance EN-31 Internal Calibration Span Calibration Linearity Calibration -OHAUS- -OHAUS- -OHAUS- 07/26/2017 05:16:53 07/26/2017 05:16:37 07/26/2017 05:16:11 Balance ID: Balance ID: Balance ID: Balance Name: PR2202 Balance Name: PR2202 Balance Name: PR2202 User Name: User Name: User Name:...
If error persists, please contact OHAUS service (www.ohaus.com - More - Contact Us) A wrong weighing pan is used Use OHAUS original weighing pan when power on. before power on. The load on the pan is over the Remove the load from the pan before initial weight setting.
If error persists, please contact OHAUS service (www.ohaus.com - More - Contact Us) Service Information If the troubleshooting section does not resolve your problem, contact an Authorized Ohaus Service Agent. Please visit our website www.ohaus.com to locate the Ohaus office nearest you.
EN-34 PR Series Balance 9. TECHNICAL DATA Specifications Ambient conditions Indoor use only Altitude: Up to 2000 m Specified Temperature range: 10° C to 30° C Humidity: maximum relative humidity 80% for temperatures up to 30° C, decreasing linearly to 50% relative humidity at 40°...
Seite 37
PR Series Balance EN-35 Table 9-1 SPECIFICATIONS InCal Model PR124 PR224 PR223 PR423 PR523 ExCal Model PR64/E PR124/E PR224/E PR223/E PR423/E PR523/E Capacity (g) Readability d (g) 0.0001 0.0001 0.0001 0.001 0.001 0.001 Repeatability (sd.), ≤5% of Full 0.00008 0.00008 0.00008 0.0008 0.0008...
Seite 38
EN-36 PR Series Balance Table 9-2 SPECIFICATIONS (continued) InCal Model PR1602 PR2202 PR4202 PR4201 PR6201 ExCal Model PR1602/E PR2202/E PR4202/E PR2201/E PR4201/E PR6201/E Capacity (g) 1600 2200 4200 2200 4200 6200 0.01 0.01 Readability d (g) 0.01 Repeatability (sd.), ≤5% of Full Load 0.008 0.008 0.008...
Seite 39
PR Series Balance EN-37 Table 9-3 SPECIFICATIONS (continued) InCal Model PR523N ExCal Model PR323N/E PR523N/E Capacity (g) Readability d (g) 0.001 or 0.01 0.001 or 0.01 Verification interval e(g) 0.01 0.01 Class Repeatability (sd.), ≤5% of Full Load (g) 0.0008 0.0008 Repeatability (sd.), 5% of Full Load to Full Range (g) 0.001...
Seite 40
EN-38 PR Series Balance Table 9-4 SPECIFICATIONS (continued) ExCal Model PR322N/E PR522N/E PR822N/E PR2202N/E PR4202N/E PR5202N/E Capacity (g) 2200 4200 5200 Readability d (g) 0.01 0.01 0.01 or 0.1 0.01 or 0.1 0.01 or 0.1 Verification interval e(g) 0.01 0.01 Class Repeatability (sd.), ≤5% 0.008...
Seite 41
PR Series Balance EN-39 Table 9-5 SPECIFICATIONS (continued) ExCal Model PR2201N/E PR4201N/E PR5201N/E PR6201N/E Capacity (g) 2200 4200 5200 6200 Readability d (g) 0.1 or1 Verification interval e(g) Class Repeatability (sd.), ≤5% of 0.08 0.08 0.08 0.08 Full Load (g) Repeatability (sd.), 5% of Full Load to Full Range (g) Linearity Deviation, Typical...
Seite 42
EN-40 PR Series Balance Table 9-6 SPECIFICATIONS (continued) InCal Approval Model PR124M PR224M PR223M PR323M PR423M PR523M Capacity (g) Readability d (g) 0.0001 0.0001 0.001 0.001 0.001 0.001 Verification Interval e (g) 0.001 0.001 0.01 0.01 0.01 0.01 Class Repeatability (sd.), ≤5% 0.00008 0.00008 0.0008...
Seite 43
PR Series Balance EN-41 Table 9-7 SPECIFICATIONS (continued) InCal Approval Model PR1602M PR2202M PR4202M PR5202M PR4201M PR6201M Capacity (g) 1600 2200 4200 5200 4200 6200 Readability d (g) 0.01 0.01 0.01 0.01 Verification Interval e (g) Class Repeatability (sd.), ≤5% of Full 0.008 0.008 0.008...
EN-42 PR Series Balance Drawings and Dimensions Fully assembled dimensions 11.93 Figure 9-1 0.001 g / 0.0001 g model Figure 9-2 0.1 g / 0.01 g model...
PR Series Balance EN-43 Accessories DESCRIPTION PART NUMBER Auxiliary Display AD7-RS 30472064 Security Device 80850043 80500524 RS232 Cable(25 pin) 80500525 RS232 Cable(9 pin) Dust Cover 30093334 In-use Cover 30372547 Printer SF40A 30064202 (EU); 30064203 (AM) Power Adapter for Balance 46001724 Communication 9.4.1 Interface Commands Commands listed in the following table will be acknowledged by the balance.
Seite 46
EN-44 PR Series Balance Command Function Abort Calibration. Print Serial Number. Print Version: print name, software revision and LFT On (if LFT is set On). Set Counting APW (x) in grams. (must have APW stored) Print Counting application APW. Set Percent application reference weight (x) in grams. (must have reference weight stored) Print Percent application reference weight.
8-bit/none (firmware selectable) Stop bits Stop bit 1, 2 Handshake None, XON/XOFF, RTS/CTS (selectable) End-of-line Not selectable SOFTWARE UPDATES Ohaus is continuously improving its balance software. To obtain the latest release, please contact your Authorized Ohaus Dealer or Ohaus Corporation.
For disposal instructions in Europe, refer to www.ohaus.com/weee. This product complies with the applicable statutory standards of the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012, UK Electromagnetic Compatibility Regulations 2016, Electrical Equipment (Safety) Regulations 2016 and Non-Automatic Weighing Instruments Regulations 2016.
Seite 49
Ohaus. In lieu of a properly returned warranty registration card, the warranty period shall begin on the date of shipment to the authorized dealer. No other express or implied warranty is given by Ohaus Corporation. Ohaus Corporation shall not be liable for any consequential damages.
Seite 51
PR Series Balance ES-1 Í ndice 1. INTRODUCCIÓN ........................3 Descripción ..............................3 Funcionalidades ............................3 Definición de las señales y sí mbolos de advertencia .................. 3 Precauciones de seguridad ......................... 3 2. INSTALACIÓN ........................4 Desembalaje ..............................4 Seleccionar la ubicación ..........................4 Nivelación ..............................
Seite 52
ES-2 PR Series Balance 5.6.8 Balance Name (Nombre de la báscula) ....................24 5.6.9 User Name (Nombre de usuario) ......................24 5.6.10 Project Name (Nombre del proyecto) ....................24 5.6.11 Application Name (Nombre de la aplicación) ..................24 5.6.12 Result (Resultados) ..........................24 5.6.13 Gross (Bruto) ............................
PR Series Balance ES-3 1. INTRODUCCIÓN Descripción La balanza PR es una balanza de precisión que le proporcionará años de servicio si se cuida correctamente. Las balanzas PR están disponibles en capacidades desde 62 gramos a 6200 gramos. Funcionalidades Controles de operación: pantalla retroiluminada, con 3 aplicaciones y varias funciones de pesaje.
ES-4 PR Series Balance 2. INSTALACIÓN Desembalaje Extraiga con cuidado la balanza PR y cada uno de sus componentes del paquete. Los componentes incluidos varí an dependiendo del modelo de balanza. Conserve el embalaje para asegurar un almacenamiento y transporte seguro. Lea el manual antes de instalar y utilizar la balanza PR para evitar un manejo incorrecto.
PR Series Balance ES-5 Conexión de la interfaz balanza PR balance tiene un puerto RS232. Utilice el puerto RS-232 para conectar con un ordenador o una impresora mediante un cable serie estándar (directo). Conexiones de interfaz en la parte posterior de la balanza RS232 RS232: utilizado para conectar a ordenador o impresora...
ES-6 PR Series Balance 3. FUNCIONAMIENTO 3.1 Descripción de la pantalla, pantalla de inicio CONTROLES FUNCIONES DE CONTROL Botón On / Zero Print Function Tare Función Si el indicador está Enví a el valor La operación Realiza la primaria en Off (apagado),...
PR Series Balance ES-7 PANTALLA DE LA APLICACIÓN PRINCIPAL Campo de resultados: Neto (NETO) dependiendo de la Estabilidad (*) aplicación Negativo (-) Centro de cero (>0<) Unidad Pre-tara (PT) Funciones principales y Menú Principal Pesaje: Pulse el botón Zero para ajustar la pantalla a cero. Coloque un objeto en el plato. La pantalla indica el peso bruto.
ES-8 PR Series Balance 4. APLICACIONES PR puede funcionar en 3 modos de aplicación con una pulsació n larga del botón Function / balanza Mode. 4.1 Pesaje Nota: antes de utilizar cualquier aplicación, asegúrese de que la está nivelada y calibrada. balanza Utilice esta aplicación para determinar el peso de los objetos en la unidad de medida seleccionada.
Seite 59
PR Series Balance ES-9 Recuento de piezas 1. Pulse Tare o Zero si es necesario para comenzar. 2. Pulse y mantenga pulsado el botón Function / Mode hasta que la palabra «Count» aparezca en la pantalla. 3. Después de confirmarlo pulsando Yes, aparecerá en la pantalla el mensaje «Clr.APwj».
ES-10 PR Series Balance Configuración del elemento Para ver o ajustar la configuración actual. Muestra: el tamaño de muestra varí a de 1 a 100. El valor predeterminado es 10. Nota: si es necesario mantener el APW de la última operación de recuento de piezas, el usuario puede pulsar No cuando la pantalla muestra el mensaje «Clr.Apwj»...
Seite 61
PR Series Balance ES-11 2. Después de confirmarlo pulsando Yes, aparecerá en la pantalla el mensaje «Clr.ref» (borrar referencia). PUt.ref 3. Pulse Yes, se mostrará el mensaje (poner el « » peso de referencia). 4. Coloque la muestra de referencia en el plato para mostrar su peso.
ES-12 PR Series Balance Configuración del elemento Nota: si es necesario mantener el peso de referencia de la última operación de pesaje porcentual, pulse No cuando Clr.ref aparezca el mensaje (borrar referencia). « » Configuración de impresión: cambiar la configuración de impresión. Vea la Sección 7 para obtener más información.
PR Series Balance ES-13 5. CONFIGURACIÓN DEL MENÚ Menú de navegación Calibration Setup Unit RS232 Print Reset Lock InCal Filter Level Gram Baud Rate Stable Only Header 1 Reset All Calibration Cal Adjust Kilogram Parity Numeric Only Header 2 Setup Span Cal Auto Tare Milligram...
ES-14 PR Series Balance 5.2.2 Calibración interna (no aplicable a modelos ExCal) La calibración se logra utilizando pesos de calibración internos. La calibración interna puede realizarse en cualquier momento, siempre y cuando la balanza esté a temperatura de funcionamiento y nivelada. Para realizar la calibración interna es necesario que la balanza esté...
PR Series Balance ES-15 Pasos para la calibración de span 1. Mantenga pulsado el botón Tare / Menu-Cal para mostrar el menú de calibración. 2. Pulse Yes para entrar en el menú de calibración. 3. Para cambiar el modo de calibración, pulse No hasta que aparezca «SpaN»...
Seite 66
ES-16 PR Series Balance 1. Mantenga pulsado el botón Tare / Menu-Cal para mostrar el menú de calibración. 2. Pulse Yes para entrar en el menú de calibración. 3. Para cambiar el modo de calibración, pulse No hasta que la pantalla muestre «LineRr (calibración de span).
PR Series Balance ES-17 Configuración de la balanza Acceda a este menú para personalizar la funcionalidad de la unidad. Nota: la configuración predeterminada de fábrica se muestra en negrita. 5.3.1 Filter Level (Nivel de filtrado) Configura la cantidad de filtrado de señales. FiltEr Low (Bajo) = tiempo de estabilización más rápido con menos estabilidad.
ES-18 PR Series Balance 5.3.4 Graduations (Divisiones) Configura la legibilidad indicada de la balanza. 1 división = legibilidad estándar. 10 divisiones = la legibilidad se incrementa por 10. Por ejemplo, si la legibilidad estándar es de 0,01 g, seleccionar 10 divisiones resultará en una lectura de 0,1 g.
PR Series Balance ES-19 5.3.8 Time Setup (Configuración de hora) Configura la hora actual al formato deseado. timME Para configurar la hora actual, pulse No o Yes para aumentar o 08.00.00 disminuir el valor. 5.3.9 Brightness (Brillo) Ajusta el brillo de la pantalla. bright mMEd Medio...
ES-20 PR Series Balance Menú de calibración: Para los modelos InCal, solo está disponible la calibración interna. Todas las demás funciones están ocultas. Menú de configuración de la balanza: El nivel de filtrado está bloqueado en el valor actual. ...
PR Series Balance ES-21 Cambiar las unidades de pesaje 1. Mantenga pulsado el botón Print / Unit hasta que Unit Menu (menú de unidades) aparezca en pantalla. 2. La unidad por defecto es el gramo (g). Para cambiar la unidad, pulse No para avanzar a la siguiente unidad. 3.
ES-22 PR Series Balance 5.5.2 Transmission (Transmissión) Configura los bits de datos, bit de parada y paridad. 8-N-1 = 8 bits de datos, sin paridad, bit de parada 1 8-N-2 = 8 bits de datos, sin paridad, bit de parada 2 7-E-1 = 7 bits de datos, paridad par, bit de parada 1 7-E-2 = 7 bits de datos, paridad par, bit de parada 2 7-N-1 = 7 bits de datos, sin paridad, bit de parada 1...
PR Series Balance ES-23 5.6.3 Single Header (Encabezado sencillo) Off = se imprimen los encabezados por cada impresión. Sin.Head On = los encabezados se imprimen una vez al dí a. 5.6.4 Auto Print (Impresión automática) Activa o desactiva la funcionalidad de impresión automá tica y A.Print el modo especí...
ES-24 PR Series Balance 5.6.6 Date and Time (Fecha y hora) On = imprime la fecha y la hora. dtmM Off = no imprime la fecha ni la hora. 5.6.7 Balance ID Id. De la bá scula) On = imprime el Id. de la balanza. Bal Id Off = no imprime el Id.
PR Series Balance ES-25 5.6.14 Net (Neto) On = imprime el peso neto. Off = no imprime el peso neto. 5.6.15 Tare (Tara) On = imprime el valor de tara. tara Off = no imprime el valor de tara. 5.6.16 Signature Line (Lí nea de firma) On = se imprime la lí...
ES-26 PR Series Balance 5.7.3 User Name (Nombre de usuario) Usr.NamM Configura el nombre de usuario. disponibles ajustes alfanumé ricos de hasta caracteres para cada configuración de encabezado. 5.7.4 Project Name (Nombre del proyecto) Configura el nombre del proyecto. Prj.NamM disponibles ajustes alfanumé...
PR Series Balance ES-27 6. LEGAL PARA COMERCIO Cuando la balanza se utiliza en actividades comerciales o una aplicación controlada legalmente, debe ser configurada, verificada y sellada según los reglamentos locales de pesos y medidas. Es la responsabilidad del comprador asegurarse de que se cumplen todos los requisitos legales pertinentes.
ES-28 PR Series Balance Verificación Un funcionario oficial de pesos y medidas o un agente de servicio autorizado debe realizar el procedimiento de verificación. 6.3 Sellado Una vez que la balanza ha sido verificada, debe ser sellada para prevenir un acceso no detectado a las configuraciones sujetas a control legal.
Utilice los comandos de la interfaz RS232 (sección 9.6.1) para controlar la balanza desde un ordenador. Software SPDC Ohaus proporciona el software SPDC / Recopilación de datos de puerto serie, y puede utilizarse en sistemas operativos que no tienen el software HyperTerminal mencionado anteriormente. El software SPDC puede recopilar y transferir preliminarmente los datos a archivos de Microsoft (como Excel, Word, etc.).
ES-30 PR Series Balance Formato de salida Los datos de los resultados, y los datos G/N/T, tienen el siguiente formato de salida. Caracteres Campo: Etiqueta Espacio Peso Espacio Unidad Espacio Estabilidad Espacio G/N Espacio terminación 1 1 3 ...
Seite 81
PR Series Balance ES-31 Calibración interna Calibración de span Calibración de linealidad -OHAUS- -OHAUS- -OHAUS- 07/26/2017 05:16:53 07/26/2017 05:16:37 07/26/2017 05:16:11 Balance ID: Balance ID: Balance ID: Balance Name: PR2202 Balance Name: PR2202 Balance Name: PR2202 User Name: User Name:...
Si el error continúa, contacte con el servicio de atención al cliente de Error del sistema Ohaus (www.ohaus.com - Más - Contacte con nosotros) Al encender, se utiliza una bandeja Utilice la bandeja de pesaje original de pesaje inadecuada.
Información de servicio Si la sección de solución de problemas no resuelve su problema, póngase en contacto con su agente de servicio autorizado de Ohaus. Visite nuestro sitio web www.ohaus.com para localizar la oficina de Ohaus má s cercana a usted.
ES-34 PR Series Balance 9. DATOS TÉCNICOS Especificaciones Condiciones ambientales Uso de interior solamente Altitud: hasta 2000 m Rango de temperatura: 10 ° C a 30 ° C Humedad: máxima humedad relativa 80 % para temperaturas hasta 30 ° C, disminuyendo linealmente a 50 % de humedad relativa a 40 °...
Seite 85
PR Series Balance ES-35 TABLE 9-1. ESPECIFICACIONES Modelo InCal PR124 PR224 PR223 PR423 PR523 Modelo ExCal PR64/E PR124/E PR224/E PR223/E PR423/E PR523/E Capacidad (g) Legibilidad d (g) 0,0001 0,0001 0,0001 0,001 0,001 0,001 Repetibilidad (sd.), ≤5% de la carga 0.00008 0.00008 0.00008 0.0008...
Seite 86
ES-36 PR Series Balance TABLE 9-2. ESPECIFICACIONES (CONT.) Modelo InCal PR1602 PR2202 PR4202 PR4201 PR6201 Modelo ExCal PR1602/E PR2202/E PR4202/E PR2201/E PR4201/E PR6201/E Capacidad (g) 1600 2200 4200 2200 4200 6200 Legibilidad d (g) 0,01 0,01 0,01 Repetibilidad (sd.), ≤5% de la carga 0.008 0.008 0.008...
Seite 87
PR Series Balance ES-37 TABLE 9-3. ESPECIFICACIONES (CONT.) Modelo InCal PR523N Modelo ExCal PR323N/E PR523N/E Capacidad (g) Legibilidad d (g) 0.001 o 0.01 0.001 o 0.01 Intervalo de verificación e (g) 0.01 0.01 Clase Repetibilidad (sd.), ≤5% de la carga completa (g) 0.0008 0.0008 Repetibilidad (sd.), 5% de carga completa a rango completo (g)
Seite 88
ES-38 PR Series Balance Table 9-4 ESPECIFICACIONES (CONT.) Modelo ExCal PR322N/E PR522N/E PR822N/E PR2202N/E PR4202N/E PR5202N/E Capacidad (g) 2200 4200 5200 0.01 o 0.1 0.01 o 0.1 Legibilidad d (g) 0.01 0.01 0.01 o 0.1 Intervalo de verificación e (g) 0.01 0.01 Clase...
Seite 89
PR Series Balance ES-39 Table 9-5 ESPECIFICACIONES (CONT.) Modelo ExCal PR2201N/E PR4201N/E PR5201N/E PR6201N/E Capacidad (g) 2200 4200 5200 6200 Legibilidad d (g) 0.1 o 1 Intervalo de verificación e (g) Clase Repetibilidad (sd.), ≤5% de la carga 0.08 0.08 0.08 0.08 completa (g)
ES-42 PR Series Balance Esquemas y dimensiones Dimensiones completamente montado 11.93 Figura 9-1. Modelo 0.001 g / 0.0001 g Figura 9-2. Modelo 0.1 g / 0.01 g...
Ninguno, XON/XOFF, RTS/CTS (seleccionable) Fin de lí nea No seleccionable 10. ACTUALIZACIONES DE SOFTWARE Ohaus está continuamente mejorando el software de sus balanzas. Para obtener la última versión, póngase en contacto con su distribuidor autorizado de Ohaus o con Ohaus Corporation.
Para consultar las instrucciones de eliminación en Europa, visite www.ohaus.com/weee. Este producto cumple con los estándares legales aplicables de la restricción del uso de ciertas sustancias peligrosas en las regulaciones de equipos eléctricos y electrónicos de...
Los productos Ohaus están garantizados contra defectos en los materiales y mano de obra desde la fecha de entrega y hasta que termine el perí odo de garantí a. Durante el perí odo de garantí a, Ohaus reparará , o si procede, reemplazará sin coste alguno cualquier componente o componentes que resulten ser defectuosos, siempre y cuando se devuelva el producto a Ohaus con los gastos de enví...
Seite 97
Balance de séries PR FR-1 Table des matières 1. INTRODUCTION ....................... FR-3 Description ............................. FR-3 Caractéristiques ............................. FR-3 Définition des symboles et signes d’avertissement ................FR-3 Précautions de sécurité ......................... FR-3 2. INSTALLATION......................... FR-4 Désemballage ............................FR-4 Sélection de la position .......................... FR-4 Nivellement ............................
Seite 98
FR-2 Balance de séries PR 5.6.8 Nom de la balance ..........................FR-21 Nom d’utilisateur ..........................FR-21 5.6.9 5.6.10 Nom du projet............................ FR-21 5.6.11 Nom d’application ..........................FR-21 5.6.12 Résultat ............................. FR-21 5.6.13 Brut ..............................FR-21 5.6.14 Net ..............................FR-21 5.6.15 Tare ..............................FR-21 5.6.16 Ligne d’alimentation ..........................
Balance de séries PR FR-3 1. INTRODUCTION 1.1 Description La balance PR est un instrument de mesure de précision offrant des années de service en cas d’utilisation appropriée. Les balances PR sont disponibles en capacités allant de 62 grammes à 6200 grammes. 1.2 Caractéristiques Contrôles d’opération: écran ré...
FR-4 Balance de séries PR 2. INSTALLATION 2.1 Désemballage Retirer soigneusement votre balance PR et chacun de ses composants de l’emballage. Les composants inclus varient en fonction du modèle de la balance. Conserver l’emballage pour assurer la sécurité du stockage et du transport. Veuillez lire entièrement le manuel avant de procéder à l’installation et à l’utilisation de la balance PR afin d’éviter une opération incorrecte.
Balance de séries PR FR-5 Branchement de l’interface La balance PR a un port RS232. Utiliser le port RS-232 pour connecter soit un ordinateur, soit une imprimante avec câble de série standard (direct). Connexions d’interface sur l’arrière de la balance RS232 RS232:Utilisé...
FR-6 Balance de séries PR 3. OPERATION 3.1 Aperçu de l’affichage, de l’écran d’accueil CONTROLES FONCTIONS DE CONTROLE Bouton Marche/Zéro Imprimer Fonction Tare Fonction primaire Si l’indicateur est L’opération Envoie la valeur de Effectue (Appuyer l’affichage actuel à l’opération tare.
Balance de séries PR FR-7 ECRAN PRINCIPAL D’APPLICATION Champ de ré sultat: En fonction de l’application Net (NET) Stabilité (*) Négatif (-) Centre de zéro (>0<) Unité Pré-tare (PT) 3.2 Fonction principales et menu principal Appuyer premiè rement sur Zé ro pour régler l’affichage à zéro. Placer un objet sur le Pesage: plateau.
FR-8 Balance de séries PR 4. APPLICATIONS La balance PR pourrait être opérée dans 3 modes d’application en appuyant longuement sur le bouton Fonction / Mode. 4.1 Pesage Remarque: Avant d’utiliser toute application, s’assurer que la balance est nivelée et calibrée. Utiliser cette application pour déterminer le poids des éléments dans l’unité...
Seite 105
Balance de séries PR FR-9 3. Après la confirmation en appuyant sur , le message Clr.APwj s’affiche à l’écran. 4. Appuyer sur Oui, et le message entrer 10 s’affiche avec le numéral 10 (défaut) clignotant. L’utilisateur pourrait appuyer sur Non ou Oui pour augmenter ou diminuer la valeur.
FR-10 Balance de séries PR Réglages d’élément Pour voir ou ajuster les réglages actuels. Échantillons: La taille d’échantillon varie de 1 à 100. La valeur par dé faut est 10. Si APW des dernières parties de l’opération de Remarque: comptage doit être maintenu, l’utilisateur pourrait appuyer sur Non Clr.Apwj (effacer le lorsque l’affichage présente le message poids moyen de la pièce Placer des objets supplémentaires...
Seite 107
Balance de séries PR FR-11 2. Après la confirmation en appuyant sur , le message Clr.ref (effacer la ré fé rence) s’affiche à l’écran. 3. Appuyer sur Oui, et mettre.ref (mettre le poids de référence) s’affiche. 4. Placer l’échantillon de référence sur le plateau pour afficher le poids.
FR-12 Balance de séries PR Réglages d’élément Remarque: Si le poids de référence de l’opération de pesage du dernier pourcentage doit être maintenu, appuyer sur Non lorsque le message Clr.ref (effacer la référence) s’affiche. Réglage d’impression: Changement des réglages d’impression. Consulter la section 7 pour des informations supplémentaires. 4.4 Fonctionnalités supplémentaires Peser en deça Remarque: S’assurer que la balance a été...
Balance de séries PR FR-13 5. REGLAGES DU MENU Menu de navigation Calibrage Réglage Unité RS232 Imprimer Réinitialiser Verrouiller Niveau de Stable Tout InCal Gramme Taux de bauds En-tête 1 Calibrage filtre uniquement réinitialiser Numérique Réglage Cal Kilogramme Parité En-tête 2 Réglage uniquement En-tête...
FR-14 Balance de séries PR 5.2.2 Calibrage interne (non applicable aux modè les ExCal) Le calibrage s’effectue avec la masse de calibrage interne. Le calibrage interne pourrait ê tre effectué à tout moment, à condition que la balance soit chauffée à la température d’opération et nivelée. Avec la balance en marche et sans change sur le plateau, le calibrage interne pourrait être effectué...
Balance de séries PR FR-15 Étapes pour le calibrage de portée 1. Appuyer et maintenir la touche Tare / Menu-Cal, et le menu de calibrage s’affiche. 2. Appuyer sur Oui pour entrer dans le menu de calibrage. 3. Pour changer le mode de calibrage, appuyer sur Non ujusqu’à...
FR-16 Balance de séries PR Étapes pour le calibrage de linéarité 1. Appuyer et maintenir la touche Tare / Menu-Cal, et le menu de calibrage s’affiche. 2. Appuyer sur Oui pour entrer dans le menu de calibrage. 3. Pour changer le mode de calibrage, appuyer sur Nonjusqu’à...
Balance de séries PR FR-17 5.3.1 Niveau de filtre FiltEr Régler la quantité du signal de filtrage. Faible = accélère le temps de stabilisation avec moins de stabilité. Moyen = temps de stabilisation normale avec la stabilité normale. Élevé = réduit le temps de stabilisation avec moins de stabilité. LowW mMed HIGH...
FR-18 Balance de séries PR 5.3.5 Format de date Régler le format de date d.FormMt mMdy actuel. MM/JJ/AAAA Format de date: Format de date AA/MM/JJ dmMy ymMd MM/JJ/AA JJ/MM/AA JJ/MM/AAAA AAAA/MM/JJ 5.3.6 Réglage de date Régler la date actuelle dans le format de date souhaitée. dAtE Pour ré...
Balance de séries PR FR-19 5.3.10 Auto Dim Régler si la balance éteint automatiquement le rétro éclairage de Aut.dimM l’affichage. Arrêt = désactivé. 10 minutes = devient dim s’il n’y a pas de mouvement pendant 10 minutes. 20 minutes = devient dim s’il n’y a pas de mouvement pendant 20 minutes. 30 minutes = devient dim s’il n’y a pas de mouvement pendant 30 minutes.
FR-20 Balance de séries PR 5.4 Unités de pesage Entrer dans le sous menu pour activer les unités désirées pour mesurer. Les balances PR fournissent un choix de 12 unité s, qui sont touts ré glables sur Activés par dé faut. Remarque: En raison des lois nationales, la balance ne pourrait pas inclure certaines des unités de mesure listées ci-dessous.
Balance de séries PR FR-21 5.5 Réglage d’interface RS232 rS232 Entrer dans le sous menu pour personnaliser les ré glages standard RS232. Les données pourraient ê tre lues sur une imprimante ou sur un PC. 5.5.1 Taux de bauds bAud Régler le taux de bauds (bits par seconde).
FR-22 Balance de séries PR 5.6.1 Stable uniquement Arrêt = Les valeurs sont imprimé es immédiatement sans Stable tenir compte de la stabilité . Marche = Les valeurs imprimées sont uniquement imprimés lorsque les critères de stabilité sont respectés. 5.6.2 Numérique uniquement Arrêt = Tous les résultats sé...
Balance de séries PR FR-23 4. Continu Continu = les impressions continuent normalement. 5.6.5 En-tête Marche = l’en-tête est imprimée. Header Arrêt = l’en-tête n’est pas imprimée. 5.6.6 Date et heure Marche = La date et l’heure sont imprimées. dtmM Arrêt = La date et l’heure ne sont pas imprimées.
FR-24 Balance de séries PR 5.6.12 Résultat Marche = le résultat de pesage est imprimé . result Marche = le résultat de pesage n’est pas imprimé. 5.6.13 Brut Marche = le poids brut est imprimé . GrosS Marche = le poids brut n’est pas imprimé. 5.6.14 Net Marche = le poids net est imprimé...
Balance de séries PR FR-25 5.7.1 En-tête Active l’impression des entêtes de BPL. Il y a trois en-tê tes Header1 disponibles. réglages alphanumériques atteignent jusqu’à En-tête 1 caractères disponibles pour chaque réglage d’en-tête. Header 2 Header3 En-tête 3 En-tête 2 5.7.2 Nom de la balance Régler le nom de la balance Bal.NamM...
FR-26 Balance de séries PR 6. CERTIFIE POUR USAGE COMMERCIAL (LFT) Lorsque l’indicateur est utilisé dans le commerce ou dans une application légalement contrôlée, elle doit être configurée, vérifiée et scellée conformément aux règlements de mesure et poids locaux. L’acheteur doit s’assurer que toutes les exigences légales pertinentes sont respectées.
Balance de séries PR FR-27 Vérification Une responsable de mesure et de poids ou un agent de service autorisé doit effectuer la procédure de vérification. 6.3 Scellement Une fois la balance vérifiée, elle doit être scellée afin d’empêcher un accès non autorisé aux réglages légalement contrôlés.
Utiliser les commandes d’interface RS232 (Section 9.6.1) pour contrôler la balance à partir d’un PC. Logiciel SPDC Le port de série des données de collecte/logiciel SPDC est fourni par Ohaus et pourrait ê tre utilisé sur les systèmes d’exploitation ne disposant pas le logiciel HyperTerminal susmentionné . Le logiciel SPDC pourrait tout d’abord collecter et transférer les données aux fichiers Microsoft (notamment Excel, Word,...
Balance de séries PR FR-29 Format d’affichage Les données de résultat et les données G/N/T sont l’affichage sous le format suivant. Étiquette Terme Champ: Espace Poids Espace Unité Espace Stabilité Espace Espace Caractères 1 1 3 8 Longueur: Remarque: 1.
Seite 126
FR-30 Balance de séries PR Calibrage interne Calibrage de portée Calibrage de linéarité -OHAUS- -OHAUS- -OHAUS- 07/26/2017 05:16:53 07/26/2017 05:16:37 07/26/2017 05:16:11 Balance ID: Balance ID: Balance ID: Balance Name: PR2202 Balance Name: PR2202 Balance Name: PR2202 User Name: User Name:...
Utilisez le plateau de pesée d’origine Un mauvais plateau de pesée est utilisé lors de la mise sous tension. OHAUS avant la mise sous tension. La charge sur le plateau dépasse le Retirez la charge du plateau avant la réglage du poids initial.
- En savoir plus - Nous contacter) Renseignement sur le service Si La section de dépannage ne résout pas votre problème; contacter votre agent de service autorisé Ohaus Veuillez visiter notre site web à l’adresse www.ohaus.com afin de localiser le bureau Ohaus le plus proche.
Balance de séries PR FR-33 9. DONNÉES TECHNIQUES Spécifications Conditions ambiantes Utilisation intérieure uniquement. Altitude: Jusqu’à 2000 m Plage de température spécifiée: 10° C à 30° C Humidité: humidité relative maximale 80% pour les températures dépassant 30° C, baissant de manière linéaire de 50% à...
Seite 130
FR-34 Balance de séries PR Tableau 9-1 SPECIFICATIONS Modèle InCal PR124 PR224 PR223 PR423 PR523 Modèle ExCal PR64/E PR124/E PR224/E PR223/E PR423/E PR523/E Capacité (g) Lisibilité d (g) 0,0001 0,0001 0,0001 0,001 0,001 0,001 Répétabilité SD, ≤5% de la pleine 0.00008 0.00008 0.00008...
Seite 131
Balance de séries PR FR-35 Tableau 9-2 SPECIFICATIONS (Suite) Modèle InCal PR1602 PR2202 PR4202 PR4201 PR6201 Modèle ExCal PR1602/E PR2202/E PR4202/E PR2201/E PR4201/E PR6201/E Capacité (g) 1600 2200 4200 2200 4200 6200 Lisibilité d (g) 0,01 0,01 0,01 Répétabilité SD, ≤5% de la pleine 0.008 0.008 0.008...
Seite 132
FR-36 Balance de séries PR Table 9-3 SPECIFICATIONS (continued) Modèle InCal PR523N Modèle ExCal PR323N/E PR523N/E Capacité (g) Lisibilité d (g) 0.001 ou 0.01 0.001 ou 0.01 Intervalle de vérification e (g) 0.01 0.01 Classe Répétabilité SD, ≤5% de la pleine charge (g) 0.00008 0.00008 Répétabilité...
Seite 133
Balance de séries PR FR-37 Table 9-4 SPECIFICATIONS (continued) Modèle ExCal PR322N/E PR522N/E PR822N/E PR2202N/E PR4202N/E PR5202N/E Capacité (g) 2200 4200 5200 0.01 ou 0.1 0.01 ou 0.1 Lisibilité d (g) 0.01 0.01 0.01 ou 0.1 Intervalle de vérification e (g) 0.01 0.01 Classe...
Seite 134
FR-38 Balance de séries PR Table 9-5 SPECIFICATIONS (continued) Modèle ExCal PR2201N/E PR4201N/E PR5201N/E PR6201N/E Capacité (g) 2200 4200 5200 6200 Lisibilité d (g) 0.1 ou 1 Intervalle de vérification e (g) Classe Répétabilité SD, ≤5% de la pleine 0.08 0.08 0.08 0.08...
Seite 135
Balance de séries PR FR-39 Table 9-6 SPECIFICATIONS (continued) Modèle InCal approuvé PR124M PR224M PR223M PR323M PR423M PR523M Capacité (g) Lisibilité d (g) 0.0001 0.0001 0.001 0.001 0.001 0.001 Intervalle de vérification e 0.001 0.001 0.01 0.01 0.01 0.01 Classe: Répétabilité...
Seite 136
FR-40 Balance de séries PR Table 9-7 SPECIFICATIONS (continued) Modèle InCal approuvé PR1602M PR2202M PR4202M PR5202M PR4201M PR6201M Capacité (g) 1600 2200 4200 5200 4200 6200 Lisibilité d (g) 0.01 0.01 0.01 0.01 Intervalle de vérification e (g) Classe: Répétabilité SD, ≤5% de la 0.008 0.008 0.008...
Balance de séries PR FR-41 Schémas et dimensions Dimensions de l’assemblage entier 11.93 Figure 9-1 0,001 g / 0,0001 g modèle Figure 9-2 0,1 g / 0,01 g modèle...
Aucun, XON/XOFF, RTS/CTS (sélectionnable) Fin de ligne Non sé lectionnable 10. MISE À JOUR DU LOGICIEL Ohaus met ré gulièrement à jour le logiciel de sa balance. Pour obtenir la version la plus récente, veuillez contacter un vendeur Ohaus autorisé ou Ohaus Corporation.
Ce produit est conforme avec les directives UE 2014/30/UE (EMC), 2014/35/UE (LVD) and 2014/31/UE (NAWI). La déclaration de conformité est disponible à l’adresse www.ohaus.com/ce Ce produit est conforme avec la directive 2012/19/UE (WEEE). Veuillez éliminer ce produit conformé ment aux règlements locaux dans le point de collecte spé cifié pour les équipements électriques et électroniques.
FR-45 GARANTIE LIMITÉE Les produits Ohaus sont garantis contre les dé faillances dans les maté riels et la fabrication à partir de la date de livraison jusqu’à la couverture entière de la période de garantie. Pendant la période de garantie, Ohaus réparera gratuitement, selon son appréciation ou remplacera tous les composants dé...
Seite 143
Waage PR Serie DE-1 Inhaltsverzeichnis 1. EINLEITUNG ........................DE-3 Beschreibung ............................DE-3 Eigenschaften ............................DE-3 Definition von Signalwarnungen und Symbolen ..................DE-3 Sicherheitsmaßnahmen ......................... DE-3 2. INSTALLATION......................... DE-4 Auspacken ............................. DE-4 Standort auswählen ..........................DE-4 Nivellierung ............................DE-4 Stromanschluss und Akklimatisierung der Waage ................DE-4 Schnittstellenanschluss ..........................
Seite 144
DE-2 Waage PR Serie 5.6.9 Benutzername..........................DE-23 5.6.10 Name des Projekts ........................... DE-23 5.6.11 Name der Anwendung ........................DE-23 5.6.12 Ergebnis ............................DE-23 5.6.13 Brutto ............................... DE-23 5.6.14 Netto ..............................DE-23 5.6.15 Tare..............................DE-23 5.6.16 Zeilenvorschub ..........................DE-23 GLP ..............................DE-26 5.7.1 Kopfzeile ............................
Waage PR Serie DE-3 1. EINLEITUNG 1.1 Beschreibung Die PR-Waage ist eine Präzisionswaage, die Ihnen bei richtiger Pflege jahrelang Dienste erweisen wird. PR-Waagen sind in Kapazitäten von 62 Gramm bis 6200 Gramm erhältlich. 1.2 Eigenschaften Bedienelemente: hintergrundbeleuchtetes Display mit 3 Wä geanwendungen und vielen Funktionen. 1.3 Definition von Signalwarnungen und Symbolen Sicherheitshinweise sind mit Signalwörtern und Warnsymbolen gekennzeichnet.
DE-4 Waage PR Serie 2. INSTALLATION 2.1 Auspacken Nehmen Sie vorsichtig Ihre PR-Waage und alle Komponenten aus der Verpackung. Die enthaltenen Komponenten variieren je nach Waagemodell. Bewahren Sie die Verpackung auf, um eine sichere Lagerung und einen sicheren Transport zu gewährleisten. Bitte lesen Sie das Handbuch vollständig durch, bevor Sie die PR-Waage installieren und verwenden, um einen fehlerhaften Betrieb zu vermeiden.
Waage PR Serie DE-5 Schnittstellenanschluss Die PR-Waage verfü gt ü ber einen RS232-Anschluss. Verwenden Sie den RS-232-Anschluss, um entweder mit einem Computer oder einem Drucker ü ber ein serielles (Straight-Through) Standardkabel zu verbinden. Schnittstellenanschlüsse auf der Rückseite der Waage RS232 RS232:Wird zum Anschluss an einen PC oder Drucker verwendet Hinweis: Siehe Drucken-Abschnitt, für Informationen zum Anschließen, Konfigurieren und Testen der Drucker- / Computerschnittstelle.
DE-6 Waage PR Serie 3. BETRIEB 3.1 Überblick über das Display und den Home-Bildschirm STEUERUNGEN STEUERUNGSFUNKTIONEN Taste Ein / Null Druck Funktion Tara Wenn die Anzeige Sendet den Der Betrieb Führt den Primärfunktion ausgeschaltet ist, aktuell hängt vom Tarabetrieb aus.
Waage PR Serie DE-7 HAUPTANWENDUNGSBILDSCHIRM Ergebnisfeld: von der Netto (NET) Anwendung abhängig Stabilität (*) Negativ (-) Nullpunkt (>0<) Einheit Vor-Tara (PT) 3.2 Hauptfunktionen und Hauptmenü Drücken Sie zuerst Null um das Display auf Null zu stellen. Legen Sie ein Objekt auf die Wiegen: Schale.
DE-8 Waage PR Serie 4. ANWENDUNGEN Die PR Waage kann in 3 Anwendungsmodi durch langes Drücken der Funktion / Modus-Taste bedient werden. 4.1 Wägung Hinweis: Bevor Sie eine Anwendung verwenden, vergewissern Sie sich, dass die Waage kalibriert wurde. Verwenden Sie diese Anwendung, um das Gewicht von Artikeln in der ausgewählten Maßeinheit zu bestimmen.
Seite 151
Waage PR Serie DE-9 Stückzählung 1. Drücken Sie Tare oder Zero wenn nötig um zu beginnen. 2. Drücken und halten Sie die Function / Mode-Taste bis Zählung erscheint. 3. Nach der Bestä tigung durch Drü cken von Yes, erscheint die Mitteilung Clr.APwj auf dem Bildschirm. 4.
DE-10 Waage PR Serie 7. Um das Gesamtgewicht oder die Anzahl der Objektstücke anzuzeigen, drücken Sie die Function / Mode Taste. Objekteinstellungen Aktuelle Einstellungen anzeigen oder anpassen. Probe: Die Stichprobengröße liegt zwischen 1 und 100. Der Standardwert ist 10. Hinweis: Wenn das APW der letzten Teilezähloperation beibehalten werden muss, kann der Benutzer No drücken, wenn das Display die Mitteilung Clr.Apwj anzeigt (Durchschnittliches Stückgewicht löschen).
Seite 153
Waage PR Serie DE-11 Prozent Wägung 1. Drücken und halten Sie die Function / Mode-Taste bis PerCent erscheint. 2. Nach Bestä tigung durch Drücken von Yes, erscheint die Mitteilung Clr.ref (Referenz löschen) auf dem Bildschirm. 3. Drücken Sie Yes, und PUt.ref (Referenzgewicht aufstellen) wird angezeigt 4.
Seite 154
DE-12 Waage PR Serie 8. Um ein neues Referenzprobengewicht zu ermitteln, drücken Sie lange auf Function / Mode und wiederholen Sie die oben beschriebenen Schritte. Objekteinstellungen Hinweis: Wenn das Referenzgewicht der letzten Prozentwiegung beibehalten werden soll, drücken Sie No wenn die Nachricht Clr.ref (Referenz löschen) angezeigt wird.
Waage PR Serie DE-13 4.4 Zusatzfunktionen Unterflur wiegen Hinweis: Stellen Sie sicher, dass die Waage nivelliert und kalibriert wurde. Die PR-Waage ist mit einer Wiegefunktion unterhalb des Hakens ausgestattet, um unter der Waage zu wiegen (siehe unten). Bevor Sie die Waage umdrehen, entfernen Sie die Wä geschale und die Windschutzelemente (falls vorhanden), um Schäden zu vermeiden.
Waage PR Serie DE-15 5.2 alibrierung PR-Waagen bieten eine Auswahl von drei Kalibrierungsmethoden: Interne Kalibrierung (nur fü r InCal- Modelle), Spannenkalibrierung und Linearitä tskalibrierung. Achtung: Stören Sie die Waage während der Kalibrierung nicht. 5.2.1 Kalibrierungsuntermenü (InCal-Modelle) Hinweis: ExCal-Modelle verfü gen nur über eine Spannenkalibrierung und eine Linearitä tskalibrierung. 5.2.2 Interne Kalibrierung (gilt nicht für ExCal-Modelle) Die Kalibrierung wird mit der internen Kalibriermasse durchgeführt.
DE-16 Waage PR Serie 5.2.4 Spannenkalibrierung Die Spannenkalibrierung verwendet zwei Kalibrierungspunkte, einen bei Nulllast und den anderen bei festgelegter Volllast (Spanne). Fü r detaillierte Informationen Kalibriermasse, siehe Spezifikationstabellen in "Spanne Kalibrierungspunkte", SPEZIFIKATIONEN, Abschnitt 9. Die Spannenkalibrierung kann bei eingeschalteter Waage und ohne Last auf der Schale durchgeführt werden.
Waage PR Serie DE-17 5.2.5 Linearität Kalibrierung Die Linearitätskalibrierung verwendet drei Kalibrierungspunkte, einen bei Nulllast und die anderen bei festgelegten Lasten. Drücken Sie die Linearitätskalibrierung, um den Prozess zu starten, ohne Last auf der Waage Die Waage erfasst den Nullpunkt und verlangt dann nach dem nächsten Gewicht. Folgen Sie den Anweisungen auf dem Display, bis die Kalibrierung abgeschlossen ist.
DE-18 Waage PR Serie 7. Entfernen Sie das Gewicht und der Messwert wird auf Null gesetzt. 5.3 Waageneinstellung Rufen Sie dieses Untermenü auf, um die Waagenfunktionalität anzupassen. Hinweis: Die werkseitigen Standardeinstellungen werden unten in Fett angezeigt. 5.3.1 Filterebene Stellen Sie den Umfang der Signalfilterung ein. FiltEr Gering = schnellere Stabilisierungszeit bei geringerer Stabilität.
Waage PR Serie DE-19 5.3.4 Abstufungen Stellt die angezeigte Lesbarkeit der Waage ein. 1 Division = Standardlesbarkeit. 10 Divisionen = Lesbarkeit ist um den Faktor 10 erhöht. Wenn die Standardlesbarkeit beispielsweise 0,01 g beträ gt, ergibt die Auswahl von 10 Divisionen einen Wert von 0,1 g.
DE-20 Waage PR Serie 5.3.8 Zeiteinstellung Stellen Sie die aktuelle Uhrzeit im gewünschten Zeitformat ein. timME Um die aktuelle Uhrzeit einzustellen, drücken Sie Nein oder Ja 08.00.00 um den Wert zu erhöhen oder zu verringern. 5.3.9 Helligkeit Stellen Sie die Helligkeit des bright mMEd Displays ein.
Waage PR Serie DE-21 Hinweis: Wenn der Genehmigt-Modus aktiviert ist, sind die Menüeinstellungen wie folgt betroffen: Kalibrierungsmenü: Für InCal-Modelle ist nur die interne Kalibrierung verfü gbar. Alle anderen Funktionen werden ausgeblendet. Waageeinstellungs-Menü: Die Filterebene ist bei der aktuellen Einstellung gesperrt. ...
DE-22 Waage PR Serie 1. Drücken und halten Sie die Taste Print / Unit Knopf bis das Einheitenmenü angezeigt wird. 2. Die Standardeinheit ist Gramm (g). Um das Gerät zu wechseln, drücken Sie No um zur nächsten Einheit zu gelangen. 3.
DE-24 Waage PR Serie 5.6.4 Auto Druck Aktivieren oder deaktivieren Sie die Funktionalität des A.Print automatischen Drucks und legen Sie den spezifischen automatischen Druckmodus fest. 1. Aus= deaktiviert 2. Bei Stabilität ON.Stab = der Druck erfolgt, wenn die Stabilitätskriterien erfüllt werden.
Waage PR Serie DE-25 On = die Waage-ID wird gedruckt. Bal Id Off = die Waage-ID wird nicht gedruckt. 5.6.8 Waage-Name On = der Waage-Name wird gedruckt. Bal.NamM Off = der Waage-Name wird nicht gedruckt. 5.6.9 Benutzername On = der Name des Benutzers wird gedruckt. Usr.NamM Off = der Name des Benutzers wird nicht gedruckt.
DE-26 Waage PR Serie 5.6.15 Tare On = das Taragewicht wird gedruckt. tare Off = das Bruttogewicht wird nicht gedruckt. 5.6.16 Unterschriften-zeile On = Die Signaturzeile wird gedruckt. SIGN.LIN Off = Die Signaturzeile wird nicht gedruckt. 5.6.17 Zeilenvorschub 1 Zeile = das Papier bewegt sich nach dem Drucken eine Feed Zeile nach oben.
Waage PR Serie DE-27 5.7.4 Name des Projekts Geben Sie den Projektnamen ein. Prj.NamM Alphanumerische Einstellungen bis zu 16 Zeichen stehen für jede Kopfzeileneinstellung zur Verfü gung. Der Standard ist leer. Zurücksetzung auf Werkseinstellungen Verwenden dieses Untermenü , alle Menüeinstellungen werkseitigen reset Standardeinstellungen zurückzusetzen.
DE-28 Waage PR Serie 6. EICHPFLICHTIGE ANWENDUNG (LEGAL FOR TRADE, LFT) Wenn die Waage im Handel oder in einer gesetzlich kontrollierten Anwendung verwendet wird, muss sie entsprechend den örtlichen Eichvorschriften aufgestellt, geprü ft und versiegelt werden. Es liegt in der Verantwortung des Käufers, sicherzustellen, dass alle relevanten gesetzlichen Anforderungen erfüllt sind.
Waage PR Serie DE-29 Überprüfung Ein lokaler Eichbeamter oder autorisierter Kundendienstvertreter muss das Prüfverfahren durchführen. 6.3 Versiegelung Nachdem die Waage überprüft wurde, muss sie versiegelt werden, um einen unerkannten Zugriff auf die gesetzlich kontrollierten Einstellungen zu verhindern. Stellen Sie vor dem Versiegeln des Geräts sicher, dass sich der Sicherheitsschalter in der gesperrten Position befindet und die Genehmigt-Modus-Einstellung im Menü...
SPDC-Software Die Serial Port Data Collection / SPDC wird von Ohaus bereitgestellt und kann auf Betriebssystemen verwendet werden, auf denen die oben genannte HyperTerminal-Software nicht installiert ist. Die SPDC- Software kann die Daten vorläufig sammeln und an Microsoft-Dateien (z. B. Excel, Word usw.) übertragen.
Waage PR Serie DE-31 Ausgabeformat Die Ergebnisdaten und B/N/T-Daten werden im folgenden Format ausgegeben. Gewicht Einheit Stabilität Abschl. Feld: Etikett Leerzeichen Leerzeichen Leerzeichen Leerzeichen Leerzeichen Zeichen 1 1 3 8 Länge: Hinweis: 1. Die Länge des Etikettfeldes ist nicht festgelegt. 2.
Seite 174
DE-32 Waage PR Serie Interne Kalibrierung Spannenkalibrierung Linearitätskalibrierung -OHAUS- -OHAUS- -OHAUS- 07/26/2017 05:16:53 07/26/2017 05:16:37 07/26/2017 05:16:11 Balance ID: Balance ID: Balance ID: Balance Name: PR2202 Balance Name: PR2202 Balance Name: PR2202 User Name: User Name: User Name: Project Name:...
Verwendung von falschen Kalibrierpunkten in der Kalibriermassen. Spezifikationstabelle der Bedienungsanleitung entsprechen. Falls der Fehler weiterhin besteht, kontaktieren Sie bitte den OHAUS- Systemfehler Service (www.ohaus.com - Mehr - Kontaktieren Sie uns) Beim Einschalten wird eine falsche Verwenden Sie vor dem Einschalten Waagschale verwendet.
Service (www.ohaus.com - Mehr - Kontaktieren Sie uns) Service-Informationen Wenn der Fehlerbehebungsabschnitt Ihr Problem nicht löst, wenden Sie sich an einen autorisierten Ohaus Service Agenten. Bitte besuchen Sie unsere Webseite www.ohaus.com, um das fü r Sie nächstgelegene Ohaus Büro zu finden.
Waage PR Serie DE-35 9. TECHNISCHE DATEN Spezifikationen Umgebungsbedingungen Nur zur Innenanwendung Höhe: Bis zu 2000 m Angegebener Temperaturbereich: 10° C bis 30° C Luftfeuchtigkeit: maximale relative Luftfeuchtigkeit 80% fü r Temperaturen bis 30° C, linear abnehmend bis 50% relative Luftfeuchtigkeit bei 40°...
Seite 180
DE-38 Waage PR Serie TABLE 9-3. SPEZIFIKATIONEN (Fortsetzung) InCal-Modell PR523N ExCal-Modell PR323N/E PR523N/E Kapazität (g) Lesbarkeit d (g) 0.001 oder 0.01 0.001 oder 0.01 Überprüfungsintervall e (g) 0.01 0.01 Klasse Wiederholbarkeit SD ≤5% der Volllast (g) 0.0008 0.0008 Wiederholbarkeit SD, 5% von Volllast bis Full Range (g) 0.001 0.001 Linearität, typisch (g)
Seite 181
Waage PR Serie DE-39 TABLE 9-4. SPEZIFIKATIONEN (Fortsetzung) ExCal-Modell PR322N/E PR522N/E PR822N/E PR2202N/E PR4202N/E PR5202N/E Kapazität (g) 2200 4200 5200 Lesbarkeit d (g) 0.01 0.01 0.01 oder 0.1 0.01 oder 0.1 0.01 oder 0.1 Überprüfungsintervall e (g) 0.01 0.01 Klasse Wiederholbarkeit SD ≤5% der 0.008 0.008...
Seite 182
DE-40 Waage PR Serie TABLE 9-5. SPEZIFIKATIONEN (Fortsetzung) ExCal-Modell PR2201N/E PR4201N/E PR5201N/E PR6201N/E Kapazität (g) 2200 4200 5200 6200 Lesbarkeit d (g) 0.1 oder 1 Überprüfungsintervall e (g) Klasse Wiederholbarkeit SD ≤5% der 0.08 0.08 0.08 0.08 Volllast (g) Wiederholbarkeit SD, 5% von Volllast bis Full Range (g) ±0.06 ±0.06...
Waage PR Serie DE-43 Zeichnungen und Dimensionen Dimensionen wenn komplett zusammengebaut 11.93 Abbildung 9-1 0,001g / 0,0001g Modell Abbildung 9-2 0,1 g / 0,01 g Modell-...
DE-44 Waage PR Serie 9.3 Zubehörteile BESCHREIBUNG TEILENUMMER Hilfsdisplay AD7-RS 30472064 Sicherheitsgerät 80850043 RS232-Kabel (25-polig) 80500524 RS232-Kabel (9-polig) 80500525 Staubschutzabdeckung 30093334 Abdeckung bei Verwendung 30372547 Drucker SF40A 30064202 (EU); 30064203 (AM) Netzteil für die Waage 46001724 Kommunikation 9.4.1 Schnittstellenbefehle Befehle, die in der folgenden Tabelle aufgeführt sind, werden von der Waage erkannt. Befehl Funktion Direkter Ausdruck des angezeigten Gewichts (stabil oder instabil).
Stoppbit 1, 2 Handschlag Keiner, XON/XOFF, RTS/CTS (auswählbar) Ende der Linie Nicht auswählbar 10. SOFTWARE UPDATES Ohaus verbessert kontinuierlich seine Waagensoftware. Um die neueste Version zu erhalten, wenden Sie sich bitte an Ihren autorisierten Ohaus-Händler oder an die Ohaus Corporation.
Produkt gemäß den örtlichen Bestimmungen an der für Elektro- und Elektronikgerä te angegebenen Sammelstelle. Für Anweisungen zur Entsorgung in Europa, siehe www.ohaus.com/weee. Dieses Produkt entspricht den geltenden gesetzlichen Normen zur Beschrä nkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten 2012, UK Electromagnetic Compatibility Regulations 2016, Electrical Equipment (Safety) Regulations 2016 und Non-Automatic Weighing Instruments Regulations 2016.
Für Ohaus-Produkte gilt eine Garantie für Material- und Verarbeitungsfehler ab dem Zeitpunkt der Lieferung für die Dauer der Garantiezeit. Wä hrend der Garantiezeit repariert Ohaus alle Komponenten, die sich als defekt erweisen, oder ersetzt diese kostenlos, sofern das Produkt frachtfrei an Ohaus zurückgesandt wird.
Seite 191
Bilancia Serie PR IT-1 Sommario 1. INTRODUZIONE ......................... IT-3 Descrizione............................... IT-3 Caratteristiche ............................IT-3 Definizione dei Segnali di Avvertimento e dei Simboli ................IT-3 Precauzioni di Sicurezza .......................... IT-3 2. INSTALLAZIONE ....................... IT-4 Disimballaggio ............................IT-4 Selezionare la Posizione .......................... IT-4 Livellamento .............................
Seite 192
IT-2 Bilancia Serie PR 5.6.9 Nome dell’Utente ..........................IT-22 5.6.10 Nome del Progetto ..........................IT-22 5.6.11 Nome dell’Applicazione ........................IT-22 5.6.12 Risultato ............................. IT-22 5.6.13 Lordo ..............................IT-22 5.6.14 Netto ..............................IT-22 5.6.15 Taratura .............................. IT-22 5.6.16 Alimentazione della Linea ........................IT-22 GLP (Buone Pratiche di Laboratorio) .....................
Bilancia Serie PR IT-3 1. INTRODUZIONE 1.1 Descrizione La Bilancia PR è uno strumento di precisione che vi offrirà molti anni di servizio se tenuta con cura. Le Bilance PR sono disponibili don capacità da 62 grammi fino a 6.200 grammi. 1.2 Caratteristiche Controlli Funzionamento:...
IT-4 Bilancia Serie PR 2. INSTALLAZIONE 2.1 Disimballaggio Rimuovere con attenzione la Bilancia PR e ciascuno dei suoi componenti dal pacchetto. I componenti inclusi variano a seconda del modello della bilancia. Conservare l'imballaggio per garantire una sicura conservazione e trasporto. Si prega di leggere completamente il Manuale prima di installare e usare la Bilancia PR per evitare errori di funzionamento.
Bilancia Serie PR IT-5 2.5 Collegamento dell’Interfaccia La Bilancia PR ha una porta RS232. Usare la porta RS-232 per collegarsi sia a un computer o a una stampante con un cavo seriale standard (diretto) Interfacciare i collegamenti sul retro della bilancia. RS232 RS232:È...
IT-6 Bilancia Serie PR 3. FUNZIONAMENTO 3.1 Visualizzazione del Display, Schermata Iniziale CONTROLLI CONTROLLO FUNZIONI Pulsante Acceso/Zero Stampa Funzione Taratura Funzione Se l’Indicatore è Invia il valore della Funzionamento Esegue il Primaria Spento, Accende corrente dipende sulla funzionamento (Premuta l’Indicatore.
Bilancia Serie PR IT-7 SCHERMO D’APPICAZIONE PRINCIPALE Risultato del Campo: Netto (NETTO) dipendente dall’applicazione Stabilità (*) Negativo (-) Centro dello zero Unità (>0<) Pre-tare (PT) 3.2 Funzioni Principali e Menu Principali Prima premere Zero per impostare il display su zero. Porre un oggetto sulla piastra della Pesatura: bilancia.
IT-8 Bilancia Serie PR 4. APPLICAZIONI La Bilancia PR può funzionare in 3 modalità d’applicazione premendo a lungo il pulsante Funzione/Modalità . 4.1 Pesatura Nota: Prima di usare qualsiasi applicazione, assicuratevi che la bilancia è a livello e tarata. Usare quest’applicazione per determinare il peso degli oggetti nella selezionata unità di misura. Pesatura 1.
Seite 199
Bilancia Serie PR IT-9 3. Dopo conferma premendo “Yes” (SI), il messaggio “Clr.APwj” apparirà sullo schermo. 4. Premere “Yes” (Sì ), e il messaggio Put10 verrà visualizzato numero (predefinito) lampeggiante. L'utente può premere “NO” (No) o “Yes” (Sì ) per aumentare o diminuire il valore. Ad esempio, per aumentare il valore a 15, premere “Yes”...
IT-10 Bilancia Serie PR Impostazioni degli Oggetti Per visualizzare o regolare le impostazioni correnti. Campione: Il numero del campione varia da 1 a 100. Il valore predefinito è 10. Nota: Se l’APW (Peso Medio del Pezzo) delle ultime parti dell’operazione di conteggio deve essere mantenuto, l’utente può...
Seite 201
Bilancia Serie PR IT-11 2. Dopo conferma premendo “Yes” (Si), il messaggio Clr.ref (clear the reference = cancellare il riferimento) apparirà sullo schermo. PUt.ref 3. Premere “Yes” (Si), e (put the reference weight = porre il peso di riferimento) sarà visualizzato. 4.
IT-12 Bilancia Serie PR Impostazioni degli Oggetti Nota: Se il peso di riferimento dell’ultima operazione della Pesatura Percentuale deve essere mantenuta, premere No Clr.ref quando il messaggio (Clear reference = Cancella riferimento) viene visualizzato. Impostazione Stampa: Cambiare l’impostazione stampa. Vedi Sezione 7 per ulteriori informazioni. 4.4 Caratteristiche Supplementari Pesatura Sotto la bilancia Nota: Assicurarsi che la bilancia è...
Bilancia Serie PR IT-13 5. IMPOSTAZIONI MENU 5.1 Menu Navigazione Calibration Setup Unit RS232 Print Reset Lock InCal Filter Level Gram Baud Rate Stable Only Header 1 Reset All Calibration Cal Adjust Kilogram Parity Numeric Only Header 2 Setup Span Cal Auto Tare Milligram Handshake...
IT-14 Bilancia Serie PR 5.2.2 Taratura Interna (non applicabile ai modelli ExCal) La taratura si ottiene con la massa di taratura interna. La Taratura Interna può essere eseguita in qualsiasi momento, a condizione che la bilancia si sia riscaldata fino alla temperatura di funzionamento e sia a livello.
Bilancia Serie PR IT-15 Passi per taratura di portata. 1. Premere e tenere premuto il pulsante Tara/Menu-Cal, e verrà visualizzato il menu Taratura.. 2. Premere “YES” (Sì ) per accedere al Menu Taratura. 3. Per cambiare la modalità di taratura, premere No finché non viene visualizzato “SPAN”...
Seite 206
IT-16 Bilancia Serie PR Passi per taratura di linearità 1. Premere e mantenere premuto il pulsante Tara/Menu- Cal, e verrà visualizzato il Menu Taratura. “YES” (Sì ) 2. Premere per accedere al menu Taratura. 3. Per cambiare la modalità di taratura, premere No fino a visualizzare “LineRr (span calibration”...
Bilancia Serie PR IT-17 5.3 Impostazione della bilancia Inviare il presente sottomenu per personalizzare la funzionalità della bilancia. Nota: Le impostazioni predefinite dalla fabbrica sono mostrate di seguito in grassetto. 5.3.1 Livello del Filtro Imposta la quantità di filtro del segnale. FiltEr asso = tempo di stabilizzazione più...
IT-18 Bilancia Serie PR 5.3.4 Graduazioni Impostare la leggibilità visualizzata della bilancia. 1 Divisione = leggibilità standard. 10 Divisioni = la leggibilità viene aumentata da un fattore di 10. Per esempio, se la leggibilità standard è 0,01 g, selezionando 10 Divisioni avranno come risultato una lettura di 0,1 g.
Bilancia Serie PR IT-19 5.3.8 Impostazione dell’Orario Impostare l’attuale orario nella formattazione del desiderato timME orario. Per impostare l’attuale orario, premere No o “Yes” (Si) per 08.00.00 aumentare o diminuire il valore. 5.3.9 Luminosità Impostare la luminosità del bright mMEd display.
IT-20 Bilancia Serie PR Taratura Menu: ● Per i modelli InCal, solamente la Taratura Interna è disponibile. Tutte le altre funzioni sono nascoste. Impostazione Menu Bilancia: ● Nell’attuale situazione il Livello del Filtro è bloccato. ● Il Tracciamento Automatico dello Zero è limitato a 0,5 Divisioni e Spento. L'impostazione selezionata è...
Bilancia Serie PR IT-21 Cambio Unità di Pesatura 1. Premere e tenere premuto il pulsante Stampa/Unità finché viene visualizzato il Menu Unità. 2. L’unità predefinita è il grammo (g). Per cambiare l’unità, premere No per passare all’unità successiva. 3. Press “Yes” (Si) per impostare l’unità visionata all’unità...
IT-22 Bilancia Serie PR 5.5.2 Trasmissione Impostare i dati bit, stop bit, e parità . 8-N-1 = 8 dati bit, no parità , stop bit 1 8-N-2 = 8 dati bit, no parità, stop bit 2 7-E-1 = 7 dati bit, no parità, stop bit 1 7-E-2 = 7 dati bit, parità...
Bilancia Serie PR IT-23 5.6.3 Intestazione Singola Spento = le Intestazioni saranno stampate per ogni Sin.Head requisito di stampa. Acceso = le Intestazioni saranno stampate una volta al giorno. 5.6.4 Auto-Stampa Abilitare o disabilitare il funzionamento di auto-stampa, e A.Print impostare la modalità...
IT-24 Bilancia Serie PR 5.6.6 Data e Orario = la data e l’orario vengono stampati. Acceso dtmM Spento = ne la data e neanche l’orario vengono stampati. 5.6.7 ID della Bilancia = l’ID della bilancia viene stampato. Acceso Bal Id Spento = l’ID della bilancia non viene stampato.
Bilancia Serie PR IT-25 Acceso = il peso netto viene stampato. Spento = il peso netto non viene stampato. 5.6.15 Taratura Acceso = il peso della taratura viene stampato. tare Spento = il peso della taratura non viene stampato. 5.6.16 Riga per la firma Acceso = viene stampata la Signature Line.
IT-26 Bilancia Serie PR Impostare il nome dell’Utente. Usr.NamM Sono disponibili delle impostazioni alfanumeriche fino a 16 caratteri per ogni impostazione dell’Intestazione. 5.7.4 Nome del Progetto Impostare il nome dell’Utente. Prj.NamM Sono disponibili delle Impostazioni alfanumeriche fino a 16 caratteri per ogni impostazione dell’Intestazione. L’impostazione predefinita è...
Bilancia Serie PR IT-27 6. (LFT) LEGALE PER IL COMMERCIO Quando la bilancia viene utilizzata in commercio o in un’applicazione legalmente controllata, deve essere installata, verificata e sigillata in conformità con le normative locali per Pesi e Misurazioni. È responsabilità dell'acquirente assicurarsi che tutti i requisiti legali pertinenti siano soddisfatti. 6.1 Impostazioni Prima della verifica e della sigillatura, eseguire i seguenti passaggi nell'ordine: Verificare che le impostazioni del menu soddisfino i regolamenti locali in materia di pesi e misure.
IT-28 Bilancia Serie PR 6.2 Verifica La procedura di verifica deve essere eseguire da un funzionario o agente dei servizi autorizzato Pesi e Misurazioni. 6.3 Sigillatura Dopo che la bilancia è stata verificata, deve essere sigillata per impedire accesso non rilevato alle impostazioni legalmente regolate.
Usare Controlli Interfaccia RS232 (Sezione 9.6.1) per controllare la bilancia da un PC. Software SPDC Il software Seriale Porta SPDC/Raccogli Dati è fornito da Ohaus e può essere utilizzato su sistemi operativi che non dispongono del software HyperTerminal menzionato in precedenza. Il software SPDC può...
IT-30 Bilancia Serie PR Formato di Output I Dati Risultanti e i dati G/N/T vengono emessi nel seguente formato Term. Campo: Etichetta Spazio Peso Spazio Unità Spazio Stabilità Caratteri 1 1 3 8 Lunghezza: Nota: 1. La lunghezza del campo dell’etichetta non è fissa. 2.
Seite 221
Bilancia Serie PR IT-31 Taratura Interna Taratura di Portata Taratura di Linearità -OHAUS- -OHAUS- -OHAUS- 07/26/2017 05:16:53 07/26/2017 05:16:37 07/26/2017 05:16:11 Balance ID: Balance ID: Balance ID: Balance Name: PR2202 Balance Name: PR2202 Balance Name: PR2202 User Name: User Name:...
Se l'errore persiste, contattare l’assistenza OHAUS (www.ohaus.com Errore del sistema - Di più - Contattaci) All'accensione viene utilizzato un Utilizzare il piatto di pesatura originale piatto per la pesatura sbagliato.
- Di più - Contattaci) Informazione di Servizio Se la sezione Risoluzione dei Problemi non risolve i vostri problemi, contattare un Agente di Servizio Ohaus Autorizzato. Si prega di visitare il nostro sito web www.ohaus.com per localizzare l‘ufficio Ohaus a voi più vicino.
IT-34 Bilancia Serie PR 9. DATI TECNICI Specifiche Condizioni ambientali Solamente uso interno Altitudine: Fino a 2.000 m Specificata gamma della Temperatura: da 10 ° C a 30 ° C Umidità: massima Umidità Relativa 80% per temperature fino a 30 ° C, diminuendo in modo lineare al 50% di Umidità...
Seite 225
Bilancia Serie PR IT-35 Tabella 9-1. SPECIFICHE Modello InCal PR124 PR224 PR223 PR423 PR523 Modello ExCal PR64/E PR124/E PR224/E PR223/E PR423/E PR523/E Capacità (g) Leggibilità d (g) 0.0001 0.0001 0.0001 0.001 0.001 0.001 Ripetibilità (sd.), ≤5% del full load (g) 0.00008 0.00008 0.00008...
Seite 226
IT-36 Bilancia Serie PR Tabella 9-2. SPECIFICHE (ripreso) Modello InCal PR1602 PR2202 PR4202 PR4201 PR6201 Modello ExCal PR1602/E PR2202/E PR4202/E PR2201/E PR4201/E PR6201/E Capacità (g) 1600 2200 4200 2200 4200 6200 Leggibilità d (g) 0.01 0.01 0.01 Ripetibilità (sd.), ≤5% del full 0.008 0.008 0.008...
Seite 227
Bilancia Serie PR IT-37 Tabella 9-3. SPECIFICHE (ripreso) Modello InCal PR523N Modello ExCal PR323N/E PR523N/E Capacità (g) Leggibilità d (g) 0.001 o 0.01 0.001 o 0.01 Intervallo di Verifica e (g) 0.01 0.01 Classe Ripetibilità (sd.), ≤5% del full load (g) 0.0008 0.0008 Ripetibilità...
Seite 228
IT-38 Bilancia Serie PR Tabella 9-4. SPECIFICHE (ripreso) Modello ExCal PR322N/E PR522N/E PR822N/E PR2202N/E PR4202N/E PR5202N/E Capacità (g) 2200 4200 5200 Leggibilità d (g) 0.01 0.01 0.01 o 0.1 0.01 o 0.1 0.01 o 0.1 Intervallo di Verifica e (g) 0.01 0.01 Classe...
Seite 229
Bilancia Serie PR IT-39 Tabella 9-5. SPECIFICHE (ripreso) Modello ExCal PR2201N/E PR4201N/E PR5201N/E PR6201N/E Capacità (g) 2200 4200 5200 6200 Leggibilità d (g) 0.1 o 1 Intervallo di Verifica e (g) Classe Ripetibilità (sd.), ≤5% del full load 0.08 0.08 0.08 0.08 Ripetibilità...
Seite 230
IT-40 Bilancia Serie PR Table 9-6 SPECIFICHE (ripreso) Modello Approvato PR124M PR224M PR223M PR323M PR423M PR523M InCal Capacità (g) Leggibilità d (g) 0.0001 0.0001 0.001 0.001 0.001 0.001 Intervallo di Verifica e (g) 0.001 0.001 0.01 0.01 0.01 0.01 Classe Ripetibilità...
Seite 231
Bilancia Serie PR IT-41 Table 9-7 SPECIFICHE (ripreso) Modello Approvato InCal PR1602M PR2202M PR4202M PR5202M PR4201M PR6201M Capacità (g) 1600 2200 4200 5200 4200 6200 Leggibilità d (g) 0.01 0.01 0.01 0.01 Intervallo di Verifica e (g) Classe Ripetibilità (sd.), ≤5% del full 0.008 0.008 0.008...
IT-42 Bilancia Serie PR 9.2 Disegni e Dimensioni Dimensioni di assemblaggio completo 11.93 Figura 9-1. Modello 0,001 g / 0,0001 g Figura 9-2. Modello 0,1 g / 0,01 g...
Bilancia Serie PR IT-43 9.3 Accessori DESCRIZIONE NUMERO PEZZO DI RICAMBIO Display Ausiliario AD7-RS 30472064 Dispositivo di Sicurezza 80850043 Cavo RS232 (25 perni) 80500524 Cavo RS232 (9 perni) 80500525 Coperchio antipolvere 30093334 Coperchio in uso 30372547 Stampante SF40A 30064202 (UE); 30064203 (USA) Adattatore di Energia per la bilancia 46001724 Comunicazione...
Stop bit 1, 2 Handshake Nessuno, XON/XSPENTO, RTS/CTS (selezionabile) Fine della linea Non selezionabile 10. AGGIORNAMENTI DEI SOFTWARE Ohaus migliora continuamente i suoi software per la bilancia. Per ottenere l'ultima versione, si prega di contattare il vostro rivenditore autorizzato Ohaus oppure Ohaus Corporation.
2012, sulle normative sulla compatibilità elettromagnetica del Regno Unito 2016, sulle normative sulle apparecchiature elettriche (di sicurezza) 2016 e sulle normative 2016 sugli strumenti di pesatura non automatica. La dichiarazione di conformità è disponibile online all'indirizzo www.ohaus.com/uk-declarations. EN 61326-1 CAN/CSA-C22.2 No. 61010-1 UL Std. No. 61010-1 Avviso importante per gli strumenti di pesatura verificati PX/PXP/PJX/PR..-M nell'UE e Regno...
Nessun'altra garanzia espressa o implicita è fornita da Ohaus Corporation. Ohaus Corporation non sarà responsabile per eventuali danni conseguenti. Poiché la legislazione sulla garanzia varia da Stato a Stato e da Paese a Paese, contattare Ohaus o il proprio rivenditore Ohaus locale per ulteriori dettagli.