Inhaltsverzeichnis
Werbung
Music streaming from a Bluetooth® unit
1. Switch on the headset (see earlier steps).
2. Start the music player on the phone (or other unit).
3. Play/Pause by pressing briefly on the On/Off button.
4. Adjust the volume by pressing the volume buttons UP/DOWN (A12, A13).
5. Move to the next track by pressing and holding down the Volume UP button for 2 seconds.
6. Play the song from the beginning by pressing and holding down the Volume DOWN button for 2 seconds.
7. Move to the previous track by pressing and holding down the Volume DOWN button for 4 seconds.
Answer/End/Reject call
Most phones send their own call signal to the headset. If not, 7 varying tones indicate an incoming call.
1. Answer a call by briefly pressing on the On/Off button. 4 ascending tones confirm the call is connected.
2. End a call by briefly pressing the On/Off button. 4 descending tones confirm the call is disconnected.
3. To reject a call, press and hold down the On/Off button for 2 seconds. 2 tones will confirm.
Voice dial from headset via connected phone
See the user instruction for your phone if it supports voice dial.
1. Press and hold the On/Off button for 3 seconds and release. An audio signal confirms the function is activated.
2. Speak your voice dial command.
Most phones that support voice-controlled dialling will send an acknowledgment signal when to speak your voice dial command.
Adjusting the volume during a call
1. Increase the volume by pressing the Volume UP button (A13)
2. Decrease the volume by pressing the Volume DOWN button (A12)
Broken Bluetooth® link
If the Bluetooth® link is broken due to exceeding the range (more than 10 meters) 3 tones will be heard in the headset and will
auto-connect when back within range. If no link has been established within 4 hours, the headset will automatically switch off.
Press and hold the On/Off button for 3 seconds to restart the headset.
Level Dependent "Active Listening" function
Press and hold the LD button (A15) to switch the Active Listening function ON. An audio signal confirms the function is activated.
The volume is adjustable in 5 levels. Adjust the volume by pressing the LD button (A15) until you reach your desired volume
level. When you reach level 5 an audio signal indicates that you have reached the maximum level. Press the LD button again to
go back to volume level 1.
Press and hold the LD button (A15) to switch the Active Listening function OFF.
The headset remembers your last volume setting the next time you switch ON the active listening function. For use in windy
environments it is recommended to fit the two included windshields (B:6). Remove the peel off film and fit the windshield
perfectly centered over the Level Dependant microphones (A7).
• This hearing protector is provided with level-dependent attenuation. The wearer should check correct operation before use. If
disortion or failure is deteced, the wearer should refer to the manufacturers advice for maintenance and charging of the battery.
• Warning! The output of the level-dependent circuit of this hearing protector may exceed the external sound level.
Wide Band Audio
The Xstream Multi-Point models also support "Wide band audio" (HD voice) when available by the phone network operator.
Low battery warning
When the battery power is decreasing and approximately one hour remains of the maximum run time, an audio signal of 3 tones
will be heard in the headset. The battery should then be charged as soon as possible. The headset will turn off when the battery
is drained.
Charging the battery
Charge the headset prior to first use!
For safety reasons, all headset functions are automatically switched off when charging.
The headset will charge when connected to a USB power supply.
Use the USB charge cable supplied with the headset (B:4). Check that the charge cable is correctly connected to the headset´s
charging socket (A8) and a USB power supply (i.e. a USB port on a PC or in a car, or your mobile phone USB charge adapter).
Make sure the power supply is of the LPS type and approved according to local directives for electronic devices.
Power supply specifications: Output DC 5V 1000 mA (Limited Power Source - LPS).
When charging, the headset LED (A11) will flash green.
When the battery is fully charged, the LED changes to solid green.
Disconnect the charger cable when headset is fully charged.
A full charge takes approximately 4 hours.
The battery run time is approximately 80 hours with an active Bluetooth® link (A2DP and/or HFP, HSP).
The stand-by time is 150 hours.
Important!
• Never leave the headset unattended when charging.
• Do not use the headset when the battery is charging.
• Only use a power supply as specified by the manufacturer.
• Only charge the headset at room temperature (10-25°C, (50-77°F)).
• This product contains a built-in Li-ion battery and it may only be replaced by authorised service personnel.
• Do not attempt to open the battery compartment in any way, and do not disassemble, crush or expose the battery to extreme
heat or fire.
• Operational temperature range for the electronic functions: -20°C (-4°F) to +55°C (+120°F).
• If these instructions are followed, the product is unlikely to present any hazards within the meaning of EN 60950-1.
7
Werbung
Inhaltsverzeichnis
