Inhaltsverzeichnis
Werbung
Instruction manual
GB
US
CA
HEADSET AND NOISE ATTENUATING HEARING PROTECTOR
This hearing protector allows communication and music streaming via Bluetooth®. The headset features wireless
communication and music streaming via units that are compatible with Bluetooth® and A2DP.
Warning!
This hearing protector is intended to protect the wearer from hazardous noise levels when fitted in accordance with this user
instruction. Any other use is not intended and therefore not permitted. It is important that the instructions for use are followed.
Failure to do so could result in a drastic decrease of the noise attenuation and may lead to serious injury.
Read these user instructions carefully!
• The hearing protector must be worn at all times in noisy environments to provide full protection! Only 100% wear time provides
full protection.
• The audibility of warning signals at a specific workplace may be impaired due to over-protection, when using a hearing
protector with too high a noise attenuation performance in relation to the noise environment.
• When using hearing protection with entertainment audio features, remember to adjust the volume when working in noisy
environments so that any warning signals etc. can be heard.
• In some individuals, excessive sound pressure from earphones and headphones may cause hearing loss.
• This product is provided with a Safety related audio input. The user should check for correct operation before use. If disortion
or failure is detected, the user should refer to manufacturers advice for maintenance.
• Do not use this product in a potentially explosive atmosphere.
• This product may be adversely affected by certain chemical substances. Further information should be sought from the
manufacturer.
• Ensure that the hearing protectors are regularly inspected for serviceability.
• The hearing protector's noise attenuating properties can dramatically decrease when used with, for example, thick eyeglass
frames, ski masks/balaclavas, etc.
• Use of perspiration/hygienic protection over the sealing rings can reduce the hearing protector's noise attenuation properties.
• Earmuffs, and in particular cushions, may deteriorate with use and should be examined at frequent intervals for cracking and
leakage.
• Immediately discard the product if it shows any signs of cracking or damage.
• Hygiene kit should be changed at least twice a year. Make sure you choose the correct hygiene kit for your hearing protector.
• Clean the product with mild soap. You must be sure that the detergent you use does not irritate the skin. Do not dip the product
in water.
• The hearing protector must be stored in a dry, clean environment out of direct sunlight, e.g. in its original packaging.
• Warning! Performance may deteriote with battery usage. The typical period of continuous use that can be expected from the
hearing protector is 80 hours.
Fitting & adjustment
Brush away all hair from your ears and place the earmuffs over your ears so they fit comfortably and snugly. Ensure your ears
are completely enclosed by the earmuffs and that you have an even pressure around your ears.
Headband (pic. C1)
Adjust the headband size so that it rests lightly against the crown of your head.
Helmet/Cap mount (pic. C2)
Push the hearing protectors' helmet attachment into the helmet slot until it locks into position.
Place the hearing protectors over your ears and press inwards until you hear a click.
Adjust the hearing protectors and helmet so they fit comfortably.
USER INSTRUCTIONS FOR BLUETOOTH® FUNCTIONS
Charge the headset prior to first use! See Charging section of the user manual.
Depending on the phone model and application, some functions may not be supported or may have to be operated on the
phone. The first time you use the headset you need to establish a wireless link, "pairing", for communication between the units.
Pairing is only needed once, for each pair of units. The headset can store up to 8 different units in its memory.
PAIRING: Enter pairing mode by pressing and holding down both volume buttons (+ / -) for 2 seconds until the LED flashes
RED/BLUE.
Activate Bluetooth® on your phone (or other unit) and select "Hellberg Xstream MP" in the list. (See the user instruction for your
phone). If the phone requires a PIN code, enter four zeros (0000).
An audio signal with 2 tones is heard in the headset, when the pairing is completed. The headset LED flashes blue. If pairing
fails, switch off the headset and start the pairing process again.
The pairing link is automatically established with the phone the next time the headset is switched on.
ON: Press and hold down the On/Off button (A14). An audio signal confirms that the headset is switched on and the LED
flashes blue.
OFF: Press and hold down the On/Off button for 4 seconds. An audio signal confirms that the headset is switched off.
Pairing with a second Bluetooth® unit
1. Re-enter pairing mode by pressing and holding down both volume buttons for 2 seconds. An audio signal confirms pairing
mode and the first paired unit is temporarily disconnected during paring with the second unit.
2. Start the Bluetooth® function on your second unit and search for and connect to Hellberg Xstream MP. An audio signal
confirm unit 2 is connected.
3. Re-connect unit 1 by selecting Hellberg Xstream MP in the display of unit 1. An audio signal confirm unit 1 is connected.
IMPORTANT! If 2 units are connected, the headset will activate the voice dial function on the first paired unit, or on the unit that
has the last outgoing call.
Xstream Multi-Point
6
Werbung
Inhaltsverzeichnis
