Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• Connect the saw to a dust collection device when sawing wood.
Always consider factors which influence exposure of dust such as:
-– type of material to be machined (chip board produces more dust
than wood);
-– sharpness of the saw blade;
-– correct adjustment of the saw blade.
Ensure that the local extraction as well as hoods, baffles and chutes are
properly adjusted.
• Please be aware of the following factors influencing exposure
to noise:
-– use saw blades designed to reduce the emitted noise;
-– use only well sharpened saw blades;
• Machine maintenance shall be conducted periodically;
• Machine faults, including guards or saw blade, shall be reported as
soon as they are discovered;
• Provide adequate general or localized lighting;
• Ensure the operator is adequately trained in the use, adjustment and
operation of the machine;
• When fitted with laser, DO NOT change to a different type of laser.
Repairs shall only be carried out by the laser manufacturer or an
authorized agent.
Residual Risks
The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of accidents caused by the uncovered parts of the rotating saw
blade.
– Risk of injury when changing the blade.
– Risk of squeezing fingers when opening the guards.
– Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
Package Contents
The package contains:
1 Assembled mitre saw
1 Blade spanner
1 Saw blade
1 Dustbag
1 LED Worklight System (DW716EXPS)
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
Description (fi g. A1–A8)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
A1
1 On/off switch
2 Moveable lower blade guard
3 Fence left-hand side
4 Mitre lever
5 Mitre latch
6 Mitre scale
7 Fence right-hand side
8 Kerf plate
9 Carrying handle
10 Operating handle
11 Head lock up release lever
12 Electronic speed control dial (DW716E)
13 Spindle lock
14 Bevel clamp handle
15 Bevel scale
16 Dust spout
A2
17 Fixed upper blade guard
18 Head lock down pin
19 Vertical position adjustment stop
20 Right-hand bevel lock override pin
21 Blade spanner
22 Hand indentation
23 Bench mounting holes
A3
24 Dustbag
Optional Accessories
A4
25 Work support extension
A5
26 Adjustable length stop
A6
27 Work piece clamp
A7
28 Laser
A8
62 LED Worklight System
INTENDED USE
Your DW716/DW716E/DW716EXPS mitre saw has been designed for
professional cutting of wood, wood products, aluminium and plastics. It will
perform the sawing operations of cross-cutting, bevelling and mitring easily,
accurately and safely.
The DW716/DW716E/DW716EXPS mitre saw is a professional power tool.
DO NOT let children come into contact with the tool. Supervision is required
when inexperienced operators use this tool.
Electrical Safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Your tool is double insulated in accordance with EN 61029;
therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the primary
and secondary winding.
If the supply cord is damaged, it must be replaced by a specially prepared
cord available through the D
WALT service organization.
E
E N G L I S H
29
Werbung
Inhaltsverzeichnis
