DeWalt DW716 Handbuch Seite 36

E N G L I S H
• To set the additional 1/4°, squeeze the mitre arm lock and carefully
move the arm to the right until the 1/4° vernier mark aligns with the
closest degree mark on the mitre scale. In this example, the closest
degree mark on the mitre scale happens to be 25°. Fig. Q3 shows a
setting of 24-1/4° right mitre.
• When mitring to the right:
– increase the mitre angle by moving the arm to align the appropriate
vernier mark with the closest mark on the mitre scale to the right.
– decrease the mitre angle by moving the arm to align the appropriate
vernier mark with the closest mark on the mitre scale to the left.
• When mitring to the left:
– increase the mitre angle by moving the arm to align the appropriate
vernier mark with the closest mark on the mitre scale to the left.
– decrease the mitre angle by moving the arm to align the
appropriatevernier mark with the closest mark on the mitre scale to
the right.
Cutting Base Mouldings
The cutting of base moulding is performed at a 45° bevel angle.
• Always make a dry run without power before making any cuts.
• All cuts are made with the back of the moulding laying flat on the saw.
Inside corner
– Left side
• Position the moulding with top of the moulding against the fence.
• Save the left side of the cut.
– Right side
• Position the moulding with the bottom of the moulding against the
fence.
• Save the left side of the cut.
Outside corner
– Left side
• Position the moulding with the bottom of the moulding against the
fence.
• Save the right side of the cut.
– Right side
• Position the moulding with top of the moulding against the fence.
• Save the right side of the cut.
Cutting Crown Mouldings
The cutting of crown moulding is performed in a compound mitre. In order
to achieve extreme accuracy, your saw has pre-set angle positions at 31.62°
mitre and 33.85° bevel. These settings are for standard crown mouldings
with 52° angles at the top and 38° angles at the bottom.
• Make test cuts using scrap material before doing the final cuts.
• All cuts are made in a left bevel and with the back of the moulding
against the base.
Inside corner
– Left side
• Top of the moulding against the fence.
• Mitre right.
• Save the left side of the cut.
– Right side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the left side of the cut.
34
Outside corner
– Left side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the right side of the cut.
– Right side
• Top of the moulding against the fence.
• Mitre right.
• Save the right side of the cut.
Dust extraction (fig. A2, A3)
• Fit the dustbag (24) onto the dust spout (16).
• Whenever possible, connect a dust extraction device designed in
accordance with the relevant regulations regarding dust emission.
Saw blades
To obtain the stated cutting capacities, always use 305 mm saw blades with
30 mm arbor holes.
Cutting non-ferrous metals
When cutting non-ferrous metals, the machine is only to be used in the mitre
saw mode. We recommend that bevel and compound mitre cuts should
not be performed in non-ferrous metals. The machine is not to be used for
cutting ferrous metals.
• Always use a material clamp when cutting non-ferrous metals. Make
sure that the workpiece is clamped securely.
• Only apply saw blades that are qualified for cutting non-ferrous metals.
• When using lubricants, only apply wax or separation spray. Do not use
emulsions or similar fluids.
• Connect an FI or DI switch between machine and mains to avoid
residual risks caused by metal swarf.
The FI switch should comply with the following specifications:
rated voltage 230 V
rated current 16 A
reaction time < 15 ms
fusing current 30 mA
The DI switch should comply with the following specifications:
DIN VDE 0661
rated voltage 230 V
rated current 16 A
fusing current 30 mA
all-pole cutoff L+N+PE
PE monitoring
low-voltage release
Transporting (fig. A2, B)
In order to conveniently carry the mitre saw, a carrying handle (9) has been
included on the top of the saw arm.
• To transport the saw, lower the head and depress the lock down pin (18).
• Always use the carrying handle (9) or the hand indentations (22) shown
in fig. A2 to transport the saw.
MAINTENANCE
Your D WALT power tool has been designed to operate over a long period
E
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing set-ups
or when making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.