Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
D
e
s
c
r
i
p
t
i
o
n
D
e
s
c
r
i
p
t
i
o
n
Pos
Denomination
1
Agitator
2
Counter-rotating beater
a) Mortar beater
b) Disc beater
3
ON / OFF-switch
4
Trip switch
5
Speed control
6
Shaft
7
Handle
8
Spanners SW 26
9
Spanners SW 24
10
Safety label
11
Charger 1,8 A
12
Accu 2,0,Ah
13
Accu 4,0 Ah
Fitting the beater
Screw
the
beater
Fix the beater using the spanners (8/9).
Do not use any device where the switch can not be
switched on and off. Damaged switches must be
repaired or replaced immediately by the customer
service.
The lithium ion batteries AP 40-4000 (Article No.
365503) or AP 40-2000 (Article No. 365501) as well
as the charger ALG 40-1800 (Article No. 365500) are
not included in the scope of delivery and must be
purchased separately.
Use only an original battery and the original
charger.
Refer to the respective "Operating instructions" for further
information on the batteries and the charger.
Inserting the battery
Insert the battery (12/13) in the device.
Make sure to slide the battery fully in until it engages with
a click.
14
o
f
d
e
v
i
c
e
/
S
p
a
r
e
p
a
o
f
d
e
v
i
c
e
/
S
p
a
r
e
p
a
Order-No.
372707
Ø 115 mm
Ø 95 mm
372700
372699
365500
365501
365503
A
s
s
e
m
b
l
y
A
s
s
e
m
b
l
y
(2)
on
the
shaft
S
t
a
r
t
-
u
p
S
t
a
r
t
-
u
p
Battery
r
t
s
r
t
s
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switching on
Start the machine at the lowest rotational speed (Level 1).
The On/Off switch is integrated in the handle.
First press the trip switch (4), keep it depressed and oper-
ate the on/off switch (3).
Switching off
The device stops automatically when you release the switch.
This machine is not suited for continuous operation.
To protect the battery the device automatically
switches off at a low battery charge and during over-
load.
Be sure not to continue operating the On/Off switch;
this may damage the battery.
Charge the lithium-ion battery ("Battery" operating
instructions).
(6).
With this type, the motor's speed and thus the agitator perfor-
mance can be adjusted. (Level 1 - 6).
You can continuously adjust the speed with the speed
control (5).
Level 1 min. power = SLOW.
Level 6 max. power = FAST.
Before starting any work read and understand
the safety notes,
following additional instructions on how to
Hold the device with both hands during mixing.
Do not reach in the running beater (rotating beater).
Avoid splashing. Work with low speed when immersing
the beater in the material to be mixed or pulling it out.
Only use beaters recommended by the manufacturer.
Pay attention the max. diameter: Ø 115 mm –
RLC 40-10 G.
The supplied counter-rotating beater is suitable for materials
with liquid, tenacious up to tough consistency: such as
paints, varnish, knifing fillers, cement, plaster, lime, con-
crete, flooring plaster, etc.
Switching on/off
Speed control
W
o
r
k
i
n
g
w
i
t
h
t
h
e
a
W
o
r
k
i
n
g
w
i
t
h
t
h
e
a
Instruction for using the agitator
work with this machine.
g
i
t
a
t
o
r
g
i
t
a
t
o
r
Werbung
Inhaltsverzeichnis
