Gude Expert Power Control 8221-Serie Anleitung Seite 93

Spezifikationen
port {port_num} resettime set {num}
port {port_num} resettime show
port {port_num} w atchdog enabled set {OFF=0|
ON=1}
port {port_num} w atchdog enabled show
port {port_num} w atchdog mode set {OFF=0|
PORT_RESET=1|IP_MS=2|IP_MS_INV=3}
port {port_num} w atchdog mode show
port {port_num} w atchdog type set {WD_ICMP=0|
WD_TCP=1}
port {port_num} w atchdog type show
port {port_num} w atchdog link dow n set {OFF=0|
ON=1}
port {port_num} w atchdog link dow n show
port {port_num} w atchdog host set "{dns_name}" sets port w atchdog host target
port {port_num} w atchdog host show
port {port_num} w atchdog port set {ip_port}
port {port_num} w atchdog port show
port {port_num} w atchdog pinginterval set {num} sets port w atchdog ping interval
port {port_num} w atchdog pinginterval show
port {port_num} w atchdog pingretries set {num} sets port w atchdog ping retries
port {port_num} w atchdog pingretries show
port {port_num} w atchdog retrybooting set
{OFF=0|ON=1}
port {port_num} w atchdog retrybooting show
port {port_num} w atchdog bootretries set {num} sets port w atchdog retry boot timeout
port {port_num} w atchdog bootretries show
port ignore pow erloss {BANK_A=1|BANK_B=2}
set <off=0/on=1>
port ignore pow erloss {BANK_A=1|BANK_B=2}
show
portsensor
portsensor all {field_list} show
portsensor {port_num} {field_list} show
portsensor {port_num} {energy_sensor} value
show
portsensor {port_num} counter reset
portsensor {port_num} {energy_sensor} events
set {OFF=0|ON=1}
portsensor {port_num} {energy_sensor} events
show
portsensor {port_num} {energy_sensor} events
type set
"{EVT_SYSLOG=0,EVT_SNMP=1,EVT_EMAIL=2,E
VT_SMS=3,EVT_GSMEMAIL=4,EVT_BEEPER=5,E
VT_DISPLAY=6,EVT_CONSOLE=7,EVT_MQTT=8}
"
portsensor {port_num} {energy_sensor} events
type show
portsensor {port_num} {energy_sensor} events
beeper mode set {CONTINOUS=0|
INTERMITTENT=1}
portsensor {port_num} {energy_sensor} events
beeper mode show
portsensor {port_num} {energy_sensor} maxval
set {num}
portsensor {port_num} {energy_sensor} maxval
show
portsensor {port_num} {energy_sensor} minval
set {num}
portsensor {port_num} {energy_sensor} minval
show
93
Expert Power Control 8221/8226
sets port reset duration
show s port reset duration
sets port w atchdog to on/off
show s port w atchdog state
sets port w atchdog mode
show s port w atchdog mode
sets port w atchdog type
show s port w atchdog type
sets if w atchdog active w hen eth link dow n
show s if w atchdog active w hen eth link dow n
show s port w atchdog host target
sets port w atchdog TCP port
show s port w atchdog TCP port
show s port w atchdog ping interval
show s port w atchdog ping retries
sets port w atchdog retry booting to on/off
show s port w atchdog retry booting state
how s port w atchdog retry boot timeout
enable no pow erport shutdow n w hen pow erloss
detected
show if pow erloss is ignored
enters cmd group "portsensor"
show s energy sensors according field list of all
port sensors
show s energy sensors according field list of one
port sensor
show s energy sensor of given port
resets energy metering counter
enables sensor events on/off
show s if sensor events are enabled
enables different event types
show s w hat event types are enabled
sets beeper tone
show s beeper tone
sets maximum value for sensor
show s maximum value for sensor
sets minimum value for sensor
show s minimum value for sensor
5
5
5
© 2022 GUDE Systems GmbH