Montage-Anschluss-Anleitung Blockschalter Sicherheitshinweise Lesen Sie die Anleitung sorgfältig und vollständig durch, bevor Sie das Gerät installieren und in Betrieb nehmen. Sie erhalten wichtige Hinweise zur Montage, Programmierung und Bedienung. Benutzen Sie das Gerät nur: - bestimmungsgemäß und - in technisch einwandfreiem und ordnungsgemäß eingebautem Zustand - gemäß...
Montage-Anschluss-Anleitung Blockschalter Funktion Der Blockschalter benötigt keine separate Betriebsspannung. Deshalb ist er speziell für Anwen- dungen geeignet, bei denen keine permanente Betriebsspannung zur Verfügung steht. Die Abtastung der Schlüsselstellung "EIN-AUS" erfolgt über Mikroschalter. Die rote und die grüne LED werden durch die angeschlossene Einbruchmelderzentrale ange- steuert.
Montage-Anschluss-Anleitung Blockschalter Montage Gehäuse öffnen Bei unvorsichtiger Handhabung kann der Bohrschutz beschädigt werden. Hinweis: Die in den folgenden Abschnitten angegebenen Nummern in ( ) beziehen sich auf die Abbildung links ("5. Aufbau"). Falls noch kein Schließzylinder eingebaut ist, entfällt der folgende Punkt 3. 1.
Montage-Anschluss-Anleitung Blockschalter Technische Daten Betriebsnennspannung, Blockspule 12 V DC Betriebsspannungsbereich 10,5 V bis 15 V DC Stromaufnahme: - Ruhestrom 0 mA - Max. Strom bei Scharf-/Unscharfschalten 270 mA Schutzklasse nach DIN 40 050 IP44 Betriebstemperaturbereich -25 °C bis +55 °C Lagerungstemperaturbereich -40 °C bis +70 °C Abmessungen (B x H x T)
Seite 8
Montage-Anschluss-Anleitung Blockschalter...
Seite 9
Mounting and Connection Instructions Block Switch s.m., Item no. 021130 Block Switch f.m., Item no. 021131 Contents Page Page 1. Safety notes ... 10 5. Set up ....12 2.
Mounting and Connection Instructions Block Switch Safety notes Read the instructions carefully and thoroughly before installing the device and putting it into operation. They contain important information on assembly, programming and operation. Only use the device: - In accordance with regulations and - When it is in a technically correct state - In accordance with technical data.
Mounting and Connection Instructions Block Switch Function A separate operating voltage is not required for the block switch. It is, therefore, especially suit- able for applications that have no permanent operating voltage. The key position "ON(EIN) / OFF(AUS) " is scanned by a micro pushbutton. The red and green LEDs are actuated by the connected intrusion detection central unit.
Mounting and Connection Instructions Block Switch Mounting Open housing Handle with care to avoid damaging protection against drilling. Note: The numbers in ( ) in the following sections refer to the illustration on the left ("5. Set up”). If there is no locking cylinder, point 3 is inapplicable. 1.
Mounting and Connection Instructions Block Switch Connection diagram + 12 V DC Block magnet Tamper Cover contact and protection against Tamper drlling LED, red + 12 V DC LED, green + 12 V DC Armed (on) Armed/ disarmed Disarmed (off) Contacts Common Monitoring resistors:...
Mounting and Connection Instructions Block Switch Technical data Rated operating voltage, block coil 12 V DC Operating voltage range 10.5 V to 15 V DC Current consumption: - No-load current 0 mA - Max. current during arming/disarming 270 mA Environmental class as per DIN 40 050 IP44 Operating temperature range -25 °C to +55 °C...