VERTO 50G175 Betriebsanleitung Seite 9

GB
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
CORDLESS DRILL
50G175
CAUTION: BEFORE USING THE POWERTOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
• Use ear protectors when operating the drill. Noise hazards may
cause hearing loss.
• Use additional handles supplied with the tool. Loss of control
may cause operator personal injury.
ADDITIONAL RULES FOR SAFE OPERATION OF
• Use only recommended battery and charger.
• Keep the battery away from heat sources. Do not leave the battery
for a long time in high temperature (in direct sunlight, in proximity
of heaters and wherever the temperature exceeds 50°C).
• The battery charging time cannot be longer than 8 hours, otherwise
the battery may be damaged.
• Avoid charging the battery in temperatures lower than 0°C.
• Charger supplied with the drill is designed for operation with this
product only. Do not use it for other purposes.
• Do not put any metal objects into the charger.
• Do not change direction of spindle rotation when the tool is
operating. Otherwise drill may be damaged.
• To clean the drill use soft, dry cloth. Never use detergents or
alcohol.
• Disconnect charger from power supply before cleaning.
• If you plan to charge more than one battery successively, make a 30
minute break between chargings.
SPECIAL CONDITIONS REGARDING SAFETY OF
CHARGER OPERATION
• Keep this manual. It contains important safety rules and rules for
charger use.
• Before using the charger read all relevant information contained
within this manual, see markings on the charger and the product
it is designed for.
• To reduce the risk of potential personal injury use the charger for
nickel-cadmium batteries only. Other type batteries may explode
and cause personal injury or material damages.
• Do not expose the charger to moisture or water.
• Use of any connecting elements not supplied or not recommended
by the manufacturer of the charger may cause fire, personal injury
or electric shock.
• Make sure the power cord is not located in pathway, it is not exposed
to treading or other danger (e.g. strong tension).
• Do not use extension cord unless it is absolutely necessary. Use
of improper extension cord may cause fire or electric shock. If it is
necessary to use extension cord, first make sure that:
– Extension cord socket matches plug prongs of the original
charger power cord.
– Extension cord is in good technical condition.
• Do not use the charger with damaged cord or plug. Damage should
be repaired by a qualified person.
• Do not use the charger after it has been hit, dropped or otherwise
damaged. Entrust the testing and potential repair to authorized
service workshop.
• Do not try to dismantle the charger. All repairs are to be made by
an authorized service workshop. Improper charger assembly may
cause electric shock or fire.
• Disconnect the charger from a power supply before starting any
maintenance or cleaning.
Disconnect the charger from mains network when it is not in use.
DRILL
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always
a small risk of operational injuries.
CONSTRUCTION AND USE
Drill is a battery-powered tool. Drive consists of DC commutator
motor with permanent magnets and planetary gear. Drill is designed
for screwing in and out screws and bolts in wood, metal, plastics and
ceramics, and for drilling holes in these materials. Cordless, battery-
powered power tools are especially useful for works in interior
furnishing, adaptation of premises etc.
Use the powertool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Quick-release chuck
2. Torque control ring
3. Direction selector switch
4. Battery lock button
5. Battery
6. Switch
7. Light
* Slight differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Battery
2. Charger
3. Charging station
4. Drills
5. Driver bits
6. Bit holder
7. Transport case
PREPARATION FOR OPERATION
REMOVING AND INSERTING THE BATTERY
• Set the direction selector switch (3) in middle position
• Push buttons (4) and slide the battery (5) down (fig. A).
• Insert charged battery (5) into the handle holder, you should hear
when the lock buttons (4) snap.
CHARGING THE BATTERY
Drill is supplied with partially charged battery. Charging the battery
should be carried out in temperature between 4°C to 40°C. New
battery, or one that have not been used for a long time, will reach full
efficiency after approximately 5 charge/discharge cycles.
9
- 2 pcs
- 1 pce
- 1 pce
- 6 pcs
- 6 pcs
- 1 pce
- 1 pce