General Power Tool Safety Warnings - Makita LH1201FL Bedienungsanleitung

Model LH1201FL 110V
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Wear ear protection
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Table Top Miter Saw
Model No./ Type: LH1201FL
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN61029
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
000331
Yasushi Fukaya
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for
future reference.
TABLE TOP MITER SAW SAFETY
WARNINGS
FOR BOTH MITER SAW MODE AND TABLE SAW
(BENCH SAW) MODE
1. Check the blade carefully for cracks or
deformation before operation.
Replace damaged blade immediately.
2. Do not operate saw without guards and riving knife
in place, especially after a mode change. Check
blade guards for proper closing before each use.
Do not operate saw if blade guards do not move
freely and close instantly. Never clamp or tie the
) : 95 dB (A)
pA
) : 108 dB (A)
WA
31.7.2015
Director
blade guards into the open position. Any irregular
operation of the blade guards should be corrected
immediately.
3. Use only saw blades specified by the
manufacturer and which conform to EN847-1.
The groove width of the cut must be thicker
than the riving knife and the blade body must
be thinner than the riving knife.
ENH003-15
4. Do not use saw blades manufactured from
high speed steel.
5. Wear eye protection.
6. Wear hearing protection to reduce the risk of
hearing loss.
7. Wear gloves for handling saw blades (saw
blades shall be carried in a holder wherever
practicable) and rough material.
8. Connect the tool to a dust collecting device
when sawing.
9. Always store the push-stick when it is not in use.
10. Keep the floor area around the tool level well
maintained and free of loose materials e.g.
chips and cut-offs.
11. The operator is adequately trained in the use,
adjustment and operation of the tool.
12. Stop and unplug the saw when unattended.
13. To reduce the emitted noise, always be sure
that the blade is sharp and clean.
14. Use only saw blades that are marked with a
maximum speed equal to or higher than the
no load speed marked on the tool.
15. When the tool is fitted with a laser or LED, do
not replace the laser or LED with a different
type. Ask an authorized service center for repair.
16. Never remove any cut-offs or other parts of
GEA010-1
the workpiece from the cutting area whilst the
tool is running with an unguarded saw blade.
17. The tool should not be used for slotting,
rebating or grooving.
18. Before carrying the tool, always cover the
upper part of the saw blade by the top guard
and secure all moving portions. When lifting
or carrying the tool, do not use the guard as a
carrying handle.
19. Clean and be careful not to damage the spindle,
ENB088-5
flanges (especially the installing surface) and hex
bolt before or when installing the blade. Damage to
these parts could result in blade breakage. Poor
installation may cause vibration/wobbling or
slippage of the blade. Use only flanges specified
for this tool.
20. Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive cut-off wheels may cause an injury.
21. Select the correct saw blade for the material
to be cut.
22. Do not cut metal objects such as nails and
screws. Inspect for and remove all nails,
screws and other foreign material from the
8