Inhaltsverzeichnis
Werbung
GB
Faulty and/or discarded electrical or electronic apparatus have to be collected
at the appropriate recycling locations.
D
Special safety instructions
NL
•
Check that the maximum speed indicated on the grinding disc corresponds to the
maximum speed of the machine. The speed of the machine must not exceed the
value on the grinding disc.
F
•
Make sure that the dimensions of the grinding disc correspond to the specifications of
the machine.
•
Make sure that the grinding disc has been mounted and fastened properly. Do not
E
use reducing rings or adapters to make the grinding disc fit properly.
•
Treat and store grinding discs in conformance with the supplier's instructions.
•
Do not use the machine for grinding workpieces with a maximum thickness exceeding
P
the maximum grinding depth of the grinding disc.
•
Do not use grinding discs for deburring.
•
When grinding discs have to be mounted on the thread of the spindle, make sure that
I
the spindle has sufficient thread. Make sure that the spindle is sufficiently protected
and does not touch the grinding surface.
•
Before use, inspect the grinding disc for any damage. Do not use grinding discs which
S
are crack-ed, ripped or otherwise damaged.
•
Before use, let the machine run idle for 30 seconds. Immediately switch off the
FIN
machine in case of abnormal vibrations or occurrence of another defect. Carefully
inspect the machine and grinding disc before switching the machine on again.
•
Make sure that sparks do not put people into danger or that they contact highly
N
flammable substances.
•
Make sure that the workpiece is sufficiently supported or clamped. Keep your hands
away from the surface to be cut.
DK
•
Always wear safety goggles and hearing protection. If desired or required also use
another kind of protection like for example an apron or helmet.
•
Ensure that mounted wheels and points are fitted in accordance with the
manufacturer's instructions.
•
Ensure that blotters are used when they are provided with the bonded abrasive
product and when they are required.
•
If a guard is supplied with the tool never use the tool without such a guard.
•
For tools intended to be fitted with threaded hole wheel, ensure that the thread in the
wheel is long enough to accept the spindle length.
•
Ensure that ventilation openings are kept clear when working in dusty conditions. If it
should become nessesary to clear dust, first disconnect the tool from the mains
supply (use non metallic objects) and avoid damaging internal parts.
•
Though poor conditions of the electrical mains, shortly voltage drops can appear
when starting the equipment. This can influence other equipment (eq. blinking of a
lamp). If the mains-impedance Zmax <0.348 Ohm, such disturbances are not
expected. (In case of need, you may contact your local supply authority for further
information.
06
CE KONFORMITETSERKLÆRING (DK)
Vi erklærer herved, udelukkende på eget ansvar, at dette
opfylder følgende standarder eller standardiserede dokumenter:
EN55014-1, EN55014-2, EN50144-1, EN50144-2-3, EN61000-3-2, EN61000-3-3
98/37/EC, 73/23/EEC, 89/336/EEC, 2002/95/EC, 2002/96/EC
Fra 01-10-2006
ZWOLLE NL
J.A. Bakker - van Ingen
CEO Ferm BV
Det er vores hensigt til stadighed at forbedre vores produkter, og vi forbeholder os derfor
til enhver tid retten til at ændre produktspecifikationerne uden forudgående varsel.
Ferm BV • Lingenstraat 6 • 8028 PM, Zwolle • Holland
Ferm
Ferm
FDAG-2000
i overenstemmelse med direktivreglerne
Quality Manager Ferm Global
GB
D
NL
F
E
P
I
S
J. Lodewijk
FIN
N
DK
91
Werbung
Inhaltsverzeichnis
