Emptying The Grass Basket; After Mowing; Cleaning, Maintenance, Storage, Transport And Ordering Of Spare Parts; Wheel Axles And Wheel Hubs - EINHELL RG-PM 51 VS B&S Originalbetriebsanleitung

Anleitung_RG_PM_51_VS_BS_SPK7:_
GB

7.4 Emptying the grass basket

As soon as grass clippings start to trail the lawn
mower, it is time to empty the grass basket.
Important! Before taking off the grass basket,
switch off the engine and wait until the blade has
come to a stop.
To take off the grass basket, use one hand to lift up
the chute flap and the other to grab onto the basket
handle (Fig. 4). Remove the basket.
For safety reasons, the chute flap automatically falls
down after removing the grass basket and closes off
the rear chute opening. If any grass remains in the
opening, it will be easier to restart the engine if you
pull the mower back approx. 1 meter.
Do not use your hands or feet to remove clippings in
or on the mower housing, but instead use suitable
tools such as a brush or a hand broom.
In order to ensure that the majority of grass clippings
are picked up, the inside of both the catch bag and
especially the air grill must be cleaned after each
use.
Reattach the catch bag only when the engine is
switched off and the blade is stopped.
Using one hand, lift up the chute flap, while grabbing
onto the basket handle with the other. Hang in the
basket from the top.

7.5 After mowing

1. Allow the engine to cool before you put the lawn
mower in an enclosed area.
2. Remove grass, foliage, grease and oil before
storing the mower. Do not place any objects on
top of the mower.
3. Check all the screws and nuts once more before
you start to use the lawn mower again. Tighten
any loose screws.
4. Also be sure to empty the grass basket.
5. Pull the spark plug boot to prevent unauthorized
use.
6. Ensure that you do not park the mower next to
any source of danger. Petrol fumes can lead to
explosions.
7. Only original parts or parts approved by the
manufacturer may be used for repairs
(see address on the warranty certificate).
8. If the lawn mower is not going to be used for an
extended period, empty the petrol tank using a
petrol suction pump.
9. Tell your children not to use the mower. It is not
a toy.
10. Never place petrol near an ignition source.
Always use a can that is approved to store
26
29.07.2011 10:39 Uhr Seite 26
petrol. Keep petrol away from children.
11. Oil and maintain the machine.
8. Cleaning, maintenance, storage,
transport and ordering of spare parts
Important: The enclosed engine manual from
Briggs & Stratton provides maintenance
information and maintenance interval
information on the engine.
Important:
Never work on or touch conducting parts on the
ignition unit with the engine running. Always pull the
spark plug boot from the spark plug before starting
any work of care or maintenance. Never perform any
work on the machine while it is running. Any work not
described in these Operating Instructions must be
performed by an authorized service workshop only.
8.1 Cleaning
After each use, the mower should be thoroughly
cleaned (especially the underside and blade
receptacle).
Note: Before you tilt the lawnmower onto its side,
empty the fuel tank completely with a petrol pump.
The lawnmower must not be tilted more than 90
degrees. The simplest time to remove dirt and grass
is directly after mowing. Dried residual grass and dirt
could cause damage to the mowing operation. Make
sure the grass ejector canal is free from residual
pieces of grass and remove these if necessary. Never
clean the mower with a direct jet of water or a high
pressure cleaner. The motor must stay dry.
Aggressive cleaning agents such as cold cleaning
solvent or petroleum ether must not be used.
8.2 Maintenance
Important: The enclosed engine manual from
Briggs & Stratton provides maintenance
information and maintenance interval
information on the engine.
Dispose of soiled maintenance material and media at
the appropriate collection point

8.2.1 Wheel axles and wheel hubs

These should be lightly greased once a season. To
do so, remove the wheel caps with a screwdriver and
slacken the fastening screws on the wheels.