Specifications - Makita 6226D Betriebsanleitung

ENGLISH
1 Button
2 Battery cartridge
3 Tighten
4 Sleeve
5 Ring
6 Switch trigger
7 Reversing switch lever

SPECIFICATIONS

Model
Capacities
Steel ........................................................... 10 mm
Wood .......................................................... 21 mm
Wood screw ................................................ 5.1 mm x 38 mm
Machine screw ............................................ 6 mm
-1
No load speed (min )
High ............................................................ 0 – 1,100
Low ............................................................. 0 – 350
Overall length ................................................ 210 mm
Net weight ...................................................... 1.4 kg
Rated voltage ................................................ D.C. 9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for drilling and screw driving in wood,
metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
All manuals and user guides at all-guides.com
Explanation of general view
8 A side
9 B side
10 Clockwise
11 Counterclockwise
12 Low speed
13 High speed
14 Speed change lever
6226D
ENC004-1
15 Adjusting ring
16 Graduations
17 Drill marking
18 Pointer
6227D
10 mm
24 mm
5.1 mm x 63 mm
6 mm
0 – 1,100
0 – 350
210 mm
1.5 kg
D.C. 12 V
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
6228D
10 mm
24 mm
5.1 mm x 63 mm
6 mm
0 – 1,100
0 – 350
210 mm
1.6 kg
D.C. 14.4 V
3