Technical Data; Before Starting The Equipment - EINHELL TE-AC 36/8 Li OF Set Originalbetriebsanleitung

4. Technical data

Motor power supply: ............................... 36 V DC
Idling speed n (pump) ........................3200 min
0
Idling speed n (motor) .......................16000 min
0
Operating pressure bar: ............................ max. 8
Theoretical suction rate l/min.: ..................... 130
Output (compressed air) at 7 bar: .... 38 liters/min
Output (compressed air) at 4 bar: .... 55 liters/min
Sound power level L
WA
Uncertainty K ............................................ 3 dB
WA
Sound pressure level L
Uncertainty K ............................................. 3 dB
pA
Protection type: ........................................... IP20
Weight of the unit in kg: ................ approx. 5.5 kg
Danger!
Noise and vibration
Sound and vibration values were measured in
accordance with EN ISO 3744.

5. Before starting the equipment

Before you connect the equipment to the power
supply make sure that the data on the rating plate
are identical to those of the rechargeable battery.
•
Check the equipment for damage which may
have occurred in transit. Report any damage
immediately to the transport company which
was used to deliver the compressor.
•
Install the compressor in the vicinity of the
point of consumption.
•
Make sure that the intake air is dry and dust-
free.
•
Do not install the compressor in a damp or
wet room.
•
The compressor may only be used in suitable
rooms (with good ventilation and an ambient
temperature from +5 °C to 40 °C). There must
be no dust, acids, vapors, explosive gases or
inflammable gases in the room.
•
The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor
in areas where work is conducted with spray-
ed water.
•
Operate the equipment only on a firm, level
surface.
•
During operation place the compressor on the
rubber feet on the back of the compressor.
Anl_TE_AC_36_8_Li_OF_Set_SPK13.indb 17 Anl_TE_AC_36_8_Li_OF_Set_SPK13.indb 17
-1
-1
in dB: .......................... 94
in dB: ...................... 83
pA
- 17 -
GB
•
Important! When you switch off the com-
pressor, excess air will escape at the safety
valve. This is not a fault, but arises in connec-
tion with the equipment's construction.
5.1 Charging the battery (Fig. 9)
1. Take the battery pack out of the tool. Do this
by pressing the pushlock button on the side.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(c) into the socket outlet. The green LED will
then begin to blink.
3. Place the battery (b) onto the charger (c).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery can become a little warm during the
charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet.
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, please send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Important!
For the best results in terms of endurance and
performance you should always use batteries with
the same capacity of 3.0 Ah or higher.
28.02.2022 08:08:51 28.02.2022 08:08:51