Technical Data - EINHELL TE-TC 18/115 Li-Solo Originalbetriebsanleitung

•
2x ring wrench/counterholder
•
Original operating instructions
•
Safety information

3. Technical data

Motor power supply ................................18 V d.c.
Idle speed n : ......................................3800 min
0
Protection class ................................................III
Cut length ............................................ Unlimited
Jolly length: .......................................... Unlimited
Cutting height 90° .................................... 24 mm
Cutting height 45° .................................... 16 mm
Cutting table-Dimensions ....... 305 mm x 335 mm
Diamond cutting wheel ........... ø 115 x ø 22.2 mm
Weight .......................................... approx. 3.4 kg
Important!
The equipment is supplied without batteries and
without a charger and is allowed to be used only
with the lithium-ion batteries of the Power X-
Change series!
The lithium-ion batteries of the Power X-Change
series are allowed to be charged only with Power
X-Chargers.
Suitable rechargeable batteries and chargers
from the Power X-Change range are for example:
•
Rechargeable battery: Power X-Change 1.5
•
Rechargeable battery: Power X-Change 5.2
•
Charger: Power X-Charger 3A
•
Charger: Power X-Charger
Danger!
Noise
The noise emission values were measured in
accordance with EN 62841-1.
Operation
L sound pressure level ..................... 80,6 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ........................ 93,6 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
The stated vibration emission levels and stated
noise emission values were measured in ac-
Anl_TE_TC_18_115_Li_SPK13.indb 18 Anl_TE_TC_18_115_Li_SPK13.indb 18
GB
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
-1
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
4. Important information
Please read the operating instructions carefully
and observe the information provided. It is im-
portant to consult these instructions in order to
acquaint yourself with the equipment, its proper
use and safety regulations.
Danger!
For safety reasons, the tile cutting machine is not
to be used by children, young people under 16
years of age, or any other persons who are not
- 18 -
12.08.2021 16:47:06 12.08.2021 16:47:06