EINHELL TE-TC 18/115 Li-Solo Originalbetriebsanleitung Seite 20

7. Assembly
Danger! Remove the battery before carrying
out any maintenance, resetting or assembly
work on the tile cutting machine.
Assemble the equipment as shown in Figs. 3-12.
7.1 Fitting the diamond cutting wheel
(Fig. 3,4,5)
To fi t the cutting wheel, proceed as follows:
•
Remove the water container cover (6) (Fig. 3).
•
Pull the cutting wheel safety guard (7) up and
out (Fig. 4).
•
Unscrew the nut (a) from the motor shaft and
remove the outer flange (15) (Fig. 4).
•
Place the cutting wheel (14) on the inner
flange and then fit the outer flange on the cut-
ting wheel. Important! Check that the cutting
wheel rotates in the correct direction!
•
Screw the nut by hand back onto the thread.
•
Place the ring wrench (19) on the nut and
use the counterholder (20) to block the motor
shaft (Fig. 5).
•
Screw the nut tight with the ring wrench.
•
Reinsert the cutting wheel safety guard and
fasten the water container cover.
7.2 Fitting the splitter (Fig. 6)
•
Unscrew the pre-fitted fastening screw (13)
out of the cutting table (4).
•
Secure the splitter (18) on the cutting table
using the fastening screw.
•
The splitter must be positioned in the center
along an imaginary line extending behind the
cutting wheel (14), so that it is not possible for
the material to get jammed.
7.3 Fitting the wheel guard (Fig. 7)
•
Place the wheel guard (3) on the splitter (18)
which is mounted on the equipment.
•
Insert the fastening screw (8) through the
wheel guard and the splitter.
•
Turn the fastening button (9) onto the faste-
ning screw.
7.4 Changing a worn diamond cutting wheel
(Fig. 3,4,5,9,12)
To replace a worn cutting wheel, proceed as
follows:
•
Remove the battery by pressing and holding
the battery catch (22) while pulling the battery
(21) out of the battery mount (24) (Fig. 9).
•
Remove the water container cover (6) (Fig. 3).
•
If necessary, screw out the water drain screw
Anl_TE_TC_18_115_Li_SPK13.indb 20 Anl_TE_TC_18_115_Li_SPK13.indb 20
GB
(11) in order to let the water out of the water
container (Fig. 12).
•
Pull the cutting wheel safety guard (7) up and
out (Fig. 4).
•
Place the ring wrench (19) on the nut (a) and
use the counterholder (20) to block the motor
shaft (Fig. 5).
•
Use the ring wrench to unscrew the nut and
remove the outer flange (15).
•
Take out the worn cutting wheel (14) and
clean the wheel flange thoroughly.
•
Place the new cutting wheel on the inner
flange and fit the outer flange back on the cut-
ting wheel. Important! Check that the cutting
wheel rotates in the correct direction!
•
Block the motor shaft again with the counter-
holder and screw the nut tight with the ring
wrench (Fig. 5).
•
Reinsert the cutting wheel safety guard and
fasten the water container cover.
8. Charging the lithium-ion battery
(Fig. 9,10)
1. Remove the battery by pressing and holding
the battery catch (22) while pulling the battery
(21) out of the battery mount (24) (Fig. 9).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(25) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery char-
ger (Fig. 10).
In section 14 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
- 20 -
12.08.2021 16:47:07 12.08.2021 16:47:07