Cleaning, Maintenance, Storage And Ordering Of Spare Parts - EINHELL GC-MT 4280 Originalbetriebsanleitung

change the working depth, move the depth
stop by sliding it up or down.
Assembling the steering handle and the se-
lector lever
1. Arrange the components properly as descri-
bed in section 2.1 Layout.
2. Fit the steering handle (33) and the selector
lever (30) as shown in Fig. 5c.
3. Fit the steering handle (38) and the cable clip
(43) as shown in Fig. 5f.
Assembling the wheels
1. Arrange the components properly as descri-
bed in section 2.1 Layout.
2. Fit the wheels (44) and the hub (45) as shown
in Fig. 11a- 11f.
Important! Before you start up for the fi rst time you
must fi ll in engine oil and fuel (7.2).
•
Check the fuel and engine oil levels and top
up if required.
•
Fill the air filter with oil (7.2).
•
Fill the gearing with oil (7.2).
•
Make sure that the ignition cable is secured to
the spark plug.
•
Check the area immediately around the pow-
er cultivator.
6. Operation
•
Set the depth stop (Fig. 4e / Item 25) to the
desired depth and secure with the split pin.
•
Swing up the transport wheel and make sure
that the bolt of the latch is engaged in the
mount at the front (Fig. 6a).
•
You can adjust the steering handle to your
physical size. To do so, loosen the handle for
height adjustment (Fig. 5c), adjust the bracket
and retighten the screws.
•
To start the star-type hoes, actuate the safety
lever 4b, and press and hold the clutch lever
4a (Fig. 6b). Releasing the clutch lever will
bring the star-type hoes to a stop (if they do
not stop, readjust the clutch cable 7.2.4).
•
To change the gear setting, release the clutch
lever (4a) to disconnect the gearing from the
engine. Use the selector lever (30) to activate
the required gear setting (Fig. 7c):
R = Reverse
0 = Idle
2 = 2nd gear
1 = 1st gear
Anl_GC_MT_4280_SPK13.indb 21 Anl_GC_MT_4280_SPK13.indb 21
GB
Warning! Risk of injury when reversing! The
machine moves towards the user.
Starting the engine
•
Ensure that the ignition cable is connected to
the spark plug.
•
Open the petrol cock (5).
•
Move the Start/Stop switch (4c) to the „ON"
position.
•
Move the choke lever (4e) to position IØI.
•
Start the engine with the reversing starter (2)
by pulling forcefully on the handle. If the engi-
ne does not start, pull the handle again.
•
Push the choke lever (4e) back again after
the engine has started.
•
Move the throttle lever (4d) into position for
the speed required.
Important!
When starting with the reversing starter, the engi-
ne might recoil suddenly as it starts up, resulting
in hand injuries. Wear protective gloves when
starting the equipment.
Important! Never allow the actuator cable to
snap back.
Important! In cold weather it might be necessary
to repeat the starting process several times.
Stopping the engine
Move the engine Start/Stop lever (4c) into the
STOP position.
7. Cleaning, maintenance, storage
and ordering of spare parts
Danger!
Pull out the spark plug boot before doing any
cleaning and maintenance work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
- 21 -
20.09.2021 11:29:45 20.09.2021 11:29:45