steute RF 96 SDS SW868-NET Montage- Und Anschlussanleitung Seite 3

RF 96 SDS SW868/SW915/SW917/SW922-NET
//
Montage- und Anschlussanleitung / Funk-Lasersensor
Mounting and wiring instructions / Wireless laser sensor
Instructions de montage et de câblage / Capteur laser sans fil
Istruzione per il montaggio e per il collegamento / Sensore laser wireless
Instruções de montagem e instalação / Sensor laser sem fio
Инструкция по монтажу и подключению / Лазерный радио-датчик
English
Penetration of radio signals:
Material
wood, gypsum, glas uncoated
brick stone, press boards
armoured concrete
metal, aluminium lamination, water
Typical ranges:
Place of use
in free field (SW868/915/917)
in free field (SW922)
indoors (SW868/915/917)
indoors (SW922)
Radio operation
The transmission of a switching command from the transmitter to the
receiver takes about 80 to 100 ms, based on the sWave® data trans-
mission. The switching signal from a transmitter may not be generat-
ed at a shorter interval, otherwise the signal will be suppressed. The
preconfigured debounce time of 5 s can be re-set using the Sensor
Bridge to between min. 1 s and max. 31 s. Measurement intervals
always equate to half the configured debounce time.
Safety
Do not use the device in conjunction with devices that directly or indi-
rectly serve health or life-safety purposes or whose operation may
cause danger to people, animals or property.
Maintenance and cleaning
With rough conditions, we recommend routine maintenance as follows:
1. Removal of all dirt particles.
2. Remove dust from sensor surfaces.
Clean enclosure on the outside only. Clean enclosure with household
cleaning agents. Do not use compressed air to clean.
Technical information
The distance is determined by measuring a light impulse. The time
required for the light impulse to travel to an object and back is used
to calculate the distance based on the speed of light. This measuring
principle means that the switching point is largely independent of the
colour and material of the object. The quantity of reflected light has
no influence on the switching distance, provided that sufficient light is
reflected for the measuring process. This is the case for conventional
materials. With some porous and very low-reflecting materials, it is
possible that the full extent of the switching distance cannot be used.
Very strongly reflecting or mirroring materials can lead to deviations
in the switching distance. In order to save energy when using a bat-
tery-driven system and thus to increase battery life, distance calcula-
tions are clocked. One measurement per 2.5 seconds and 5 seconds
debounce time are standard values which provide a good compromise
between response time and battery life.
Battery
Penetration
The battery charge is displayed in the description of interface in par-
90...100 %
agrph »RECORD.BATT« as mV (see RF RxT SW868/915/917/922-NET,
65...95 %
»Description of interface/Wireless receiver«, section »DataMessage«,
download from www.steute.co.uk).
10...90 %
When the battery voltage acc. to the radio protocol drops below approx.
0...10 %
<3200 mV (at 20°C, load approx. 20 mA), it may be assumed that the
battery is empty. Attention: The open circuit voltage measurement
does not provide reliable information! In order to ensure reliable
functioning, the battery must be replaced. To do this, the 5 screws in
Wireless range (approx.)
the housing cover must be opened using a torx-8 screwdriver. The
450 m
battery should be inserted in the direction shown by the symbols on
the cover. Use only the designated battery type or a complementary
150 m
battery type. Depending on the country the device is supplied to, deliv-
40 m
ery will include an AA lithium battery SL-760/3.6 V/2.2 Ah in a battery
20 m
adapter, or a lithium battery SL-2770/3.6 V/8.5 Ah without an adapter
or a complementary battery type. Once the battery has been changed,
the housing must be closed and the screws replaced, tightened with a
torque of approx. 0.45 Nm. The sealing must not be contaminated by
any foreign bodies.
Spare part:
Name
Lithium battery SL-2770/S 3.6 V/8.5 Ah
Lithium battery SL-760 (3.6 V/2.2 Ah AA)
Disposal
- Observe national, local and legal regulations concerning disposal.
- Recycle each material separately. Dispose of possibly contained
N.B.
The described products have been developed in order to assume
functions as part of an entire plant or machine. It is the responsibility
of the manufacturer of a plant or machine to guarantee the correct
general function. Subject to technical modifications. Reconstruction
and alterations to the device are not allowed. steute does not assume
any liability for recommendations made or implied by this description.
New claims for guarantee, warranty or liability cannot be derived from
this document beyond the general terms and conditions of delivery.
ESD
Ensure adequate ESD protection for all work that requires opening
the unit.
3 / 20
batteries correctly.
Material No.
1202806
1351045