Driving The Machine; Work Method - Comet Spa CPS 36 E Bedienungsanleitung

6.11.

DRIVING THE MACHINE

Model AC
- Connect the power cable of the machine ( Photo 6 -
A ) to the power mains using a patch cord.
- Switch ON the general ON-OFF switch ( Photo 5 - A ).
- Switch ON the brush motor switch ( Photo 5 - D )
• The brush will start the rotation only when
the operator will pull the brush operation lever
( Photo 2 - A ).
- Switch ON the suction motor switch ( Photo 5 - B ).
- Switch ON the solenoid valve switch for solution
water outlet ( Photo 5 - C ).
- Open the solution water valve rotating the lever (
Photo 31, 32, 33 ).
- Lower the squeegee unit by using the lift/lower
lever ( Photo 2 - B ).
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo 2 - A ) to start the brush
rotation and the solution water outlet; releasing the
lever the brush rotation will stop after few seconds.
• Remember to lift the squeegee before driving re-
verse to avoid damaging it.
Model DC 12V
- Verify that the battery connector placed under the
recovery tank ( Photo 16 - B ) is connected.
- Put the ignition key ( Photo 8 - A ) in and turn ON
the machine.
- On the on-board battery charger ( Photo 19 ) check
the battery charge status ( Photo 18 ).
- Switch ON the brush motor switch ( Photo 7 - C )
• The brush will start the rotation only when
the operator will pull the brush operation lever
( Photo 2 - A ).
- Switch ON the suction motor switch ( Photo 7 - A ).
- Switch ON the solenoid valve switch for solution
water outlet ( Photo 7 -B ).
- Open the solution water valve rotating the lever (
Photo 31, 32, 33 )
- Lower the squeegee unit by using the lift/lower
lever ( Photo 2 - B ).
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo 2 - A ) to start the brush
rotation and the solution water outlet; releasing the
lever the brush rotation will stop after few seconds.
• Remember to lift the squeegee before driving re-
verse to avoid damaging it.
6.12.

WORK METHOD

6.12.1. PREPARATION AND WARNINGS
Remove any loose solid residue from the surface
to be treated (using suitable tools, such as vacuum
6. OPERATING INFORMATIONS
cleaners, sweepers, etc.). It this is not done, the solid
dirt might prevent the squeegee from operating cor-
rectly, reducing drying efficiency.
Only trained personnel can drive this machine.
6.12.2. BATTERY CHARGE LEVEL CONTROLS
The sequence of lights of the battery charge control
( Photo 18 - C, B, A ) shows the battery discharging.
When the red light turns on ( Photo 18 - A ), turn off
the brush motor, close the detergent solution outlet,
finish drying the small residual moisture and go to
the battery charging area to charge the battery.
• The battery may be irreparably damaged if the
residual charge level drops too low (see the bat-
tery operating manual). Do not force the battery
discharge beyond the safety limits, turning the
key off and on or in any other manner.
6.12.3. DIRECT SCRUBBING OR FOR SLIGHTLY
Scrubbing and drying in a single pass.
Prepare the machine as previously described and use
it as described in paragraph 7.12 .
☞ Never use the machine without the detergent
solution: the floor might be damaged.
6.12.4. INDIRECT SCRUBBING OR FOR VERY
Scrubbing and drying in various passes.
Prepare the machine as previously described.
First set of operations:
Wash the floor as described in paragraph 7.11 without
drying the floor
Allow the detergent solution to work on the dirty
floor according to what is indicated in the infor-
mation relative to the detergent used.
Second set of operations:
Proceed as explained in the previous "Direct Washing"
paragraph (7.13.3) to also proceed with drying the floor.
☞ Never use the machine without the detergent
solution: the floor might be damaged.
6.12.5. POST-SCRUBBING OPERATIONS
Close the detergent solution outlet.
After having completely dried any traces of water
on the surface, wait a few seconds and then lift the
squeegee and turn off the suction motor.
Move to a suitable location to drain the tanks; empty
and clean the tanks (see 7.10).
it from the control panel.
If necessary, charge the battery (see the relative section).
45
DIRTY SURFACES
DIRTY SURFACES