Drive Speeds; Motion Warning Alarm; Ac Generator - Upright AB60JRT Betriebsanleitung

For operation on grades up to 20 percent, it is recom-
mended that the riser and main booms be fully lowered
and the jib elevated just enough to provide adequate
ground clearance. A 20 percent grade is a 61 cm (24")
vertical rise in 3.05 m (10') horizontal length.
Avoid driving with the platform over the front (steer) end
of the chassis. In this position the machine is difficult to
control because:
• drive and steer control movements and their result-
ing machine movements are reversed.
• when driving fast, sudden turns or stops produce
more severe reactions to platform occupants.
• more turning space is required to prevent the
platform from colliding with obstacles several feet
beyond the path of the tires.
A
Warning
Death or serious injury can result from improperly
driving or steering the aerial platform. Read and un-
derstand the information in this manual and on the
placards and decals on the machine before operating
the aerial platform on the job.
The blue and yellow arrows on the chassis indicate the
direction the chassis will move when the drive or steer
control is moved toward the corresponding color.
When the machine is in the stowed position, with the
booms centered between the rear wheels, the direction
of drive and steer control movement corresponds with
the direction of chassis movement.
When the turntable is rotated from the stowed position,
with the booms to either side of or in front of the chassis,
the direction of control movement does not correspond
with the direction of chassis movement.
To avoid confusion, always drive to the work area or
move between work areas with the turntable and booms
in the stowed position. After arriving at the work area, the
booms may be positioned to the side or the front of the
chassis for final positioning. Always look in the direction
of movement as indicated by the directional arrows on
the chassis.
Use the following procedure to operate the drive and
steer functions.
1. Determine the desired drive range for the specific
driving conditions.
• Use high range when traveling across fi rm, fl at,
level surfaces. High range can only be activated
when the booms are stowed. High range is for high
speed, low torque operation.
• Use low range for driving on loading ramps or
other steep grades and when safety considerations
AB60JRT
demand slow deliberate machine movement. Low
range is for low speed, high torque operation.
2. Place the drive/boom selector switch in the drive
position.
3. Step down on the platform foot switch.
4. Push the drive joystick forward to move the chas-
sis forward, the direction of the blue arrow. Pull the
joystick backward to move the chassis backward,
the direction of the yellow arrow. The drive speed is
proportional to the joystick position.
5. To stop drive motion, return the joystick to neutral.
6. Push the drive joystick to the right to steer to the right,
the direction of the yellow arrow. Push the joystick
to the left to steer to the left, the direction of the blue
arrow.
Note
The steering wheels are not self-centering. Set the steer-
ing wheels straight ahead after completing a turn.
7. After driving to the desired location, release the foot
switch, or push the emergency stop button to apply
the parking brakes.

Drive Speeds

The drive speed is proportional to the joystick position.
The farther the joystick is moved, the faster the travel
speed.
Always slow down and shift the drive system to low
range before traveling over rough terrain or any sloped
surface.
Drive speed ranges are interlocked through a limit switch
that senses the main boom position. When the boom is
elevated, only the slowest drive speed will work regard-
less of the drive range switch position.
A
Warning
The potential for an accident increases when safety
devices do not function properly. Death or serious
injury can result from such accidents. Do not alter,
disable or override any safety device.
Do not use the aerial platform if it drives faster than 1.1
km/h (0.7 mile per hour) [9.7 m (32 feet) in 30 seconds]
when the booms are elevated from the stowed position.

Motion Warning Alarm

The optional motion warning alarm sounds loud intermit-
tent beeps when the drive joystick is in the forward or
reverse position.

AC Generator

The generator supplies power to the electrical outlet only
when the engine is running and the machine is stationary.
The machine functions will not operate when the machine/
generator selector switch is in the generator position.
Operation
11