Lens dimension ..................20 RS232 command control ..............21 RS232 pin assignment ....................21 RS232 serial port with a crossover cable ..............21 PJLink ..........................29 Please visit below website for latest version of User Manual / Installation Guide. http://business-display.benq.com/ V1.00...
Notice Notice on laser This symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely followed. y Laser class (for USA) This Laser Product is designated as Class 3R during all procedures of operation and complies with IEC/EN 60825-1:2007.
Cooling notice Allow at least 50 cm (19.7 inch) for clearance around the exhaust vent. Make sure no objects block air input within 30 cm (11.8 inch). Keep the outlet at least 1 m away from the inlets of other projectors. Air inlet Air inlet Air outlet...
Seite 5
• Allow at least 50 cm of clearance around the exhaust vent. Minimum 50 cm Minimum 50 cm Minimum 50 cm (19.69 inch) (19.69 inch) (19.69 inch) Minimum 50 cm (19.69 inch) Minimum 10 cm (3.94 inch) Minimum 50 cm (19.69 inch) Minimum 30 cm (11.81 inch)
Make sure the port is valid before inserting a wired remote controller. The remote controller may be damaged in case of an invalid port, e.g. a wired remote controller is connected to trigger output. For more information about upgrading firmware via Lan, please contact BenQ service.
Remote control ON / OFF Toggles the projector between standby mode and on. KEYSTONE+/KEYSTONE- Manually corrects distorted images resulting from an angled projection. VOLUME +/VOLUME - Increases/decreases the projector volume. QUICK INSTALL Displays the Quick Install OSD menu. MUTE Toggles projector audio between on and off. Arrow keys (▲...
Seite 9
OVERSCAN Press to select overscan mode. FREEZE Freezes the projected image. LAMP MODE Press to display OSD menu to select desired light mode. 3D MODE Press to display 3D setup menu. INFO. Press to display INFORMATION menu. LIGHT Press to open backlight of remote controller. CLEAR Clear remote ID SET assigned to all projectors.
Installation Caution: To avoid damaging the DLP chips, never aim a high-power laser beam into the projection lens. Installing removing the optional lens Caution: • Do not shake or place excessive pressure on the projector or the lens components as the projector and lens components contain precision parts.
Seite 11
y Removing the existing lens from the projector 1. Push the LENSE RELEASE button to the unlock position. 2. Grasp the lens. 3. Rotate the lens counterclockwise. The existing lens will be disengaged. 4. Pull out the existing lens slowly.
Horizontal: -5%-5% Projection table *** "A" is based on maximum lens shift offset position 55% • LU9255 The screen aspect ratio is 16:10 and the projected picture is 16:10. Note: To optimize the projection quality, we suggest to project images in an area without grayscale.
Seite 13
13.46 17.23 Note: • For more visualized instructions, please go to BenQ calculator website http://projectorcalculator.benq.com/. • Ceiling installation must be done by a qualified professional. Contact your dealer for more information. It is not recommended you install the projector yourself.
Lens shift range y Lens shift adjustable range The adjustable range for lens shift is tabulated below and subject to the conditions listed. • LU9255 Normal projection position Desk-Front Projection Vertical shift Max 0.55V Height of projected image Vertical shift Max 0.15V...
LED indicator y System message Power Temp Light Filter Status & Description Orange Stand-by Green Powering up Flashing Green Normal operation Orange Normal power-down cooling Flashing Download Green CW start fail Red Flash- Green Phosphor Wheel start fail Red Flash- Scaler shutdown fail(data abord) Scaler reset fail(video projector only) LAN download fail...
Seite 17
y Lamp Error Messages Power Temp Light Filter Status & Description Lamp1 error in normal operation Lamp2 error in normal operation Both Lamp fail Lamp is not lit up Flashing y Thermal Error Messages Power Temp Light Filter Status & Description Fan 1 error (the actual fan speed is outside the desired speed) Fan 2 error (the actual fan speed is outside the desired...
Seite 18
Power Temp Light Filter Status & Description Green Green Thermal IC #2 I2C Connection error Flashing Flashing Green Temperature 3 error (over limited temperature) Green Thermal Sensor 3 open error Flashing Green Green Thermal Sensor 3 short error Green Green Thermal IC #3 I2C Connection error Flashing Green...
Ceilling mount installation diagram BenQ ceilling mount CMG6 (5A.JHS10.001) Material Steel Weight 10.5kg (23.1lbs) Dimension (W x H x D) 410 x 641 x 360 mm (16.14" x 25.24" x 14.17") Length 491mm ~ 641mm Tilt Angle Swivel: ±5° Vertical: +5°/-25°...
RS232 command control RS232 pin assignment Serial Serial Short with pin8 Short with pin7 Ground RS232 serial port with a crossover cable Function Type Operation ASCII Power Write Power On <CR>*pow=on#<CR> Write Power off <CR>*pow=off#<CR> Read Power Status <CR>*pow=?#<CR> Source Selec- Write COMPUTER/YPbPr <CR>*sour=RGB#<CR>...
Seite 23
Function Type Operation ASCII Audio Source Write Audio pass Through off <CR>*audiosour=off#<CR> Select Write Audio-Computer1 <CR>*audiosour=RGB#<CR> Write Audio-Video/S-Video <CR>*audiosour=vid#<CR> Write Audio-HDMI <CR>*audiosour=hdmi#<CR> Write Audio-HDMI2 <CR>*audiosour=hdmi2#<CR> Read Audio pass Status <CR>*audiosour=?#<CR> Picture Mode Write Presentation <CR>*appmod=preset#<CR> Write sRGB <CR>*appmod=srgb#<CR> Write Bright <CR>*appmod=bright#<CR>...
Seite 24
Function Type Operation ASCII Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=5#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=5#<CR> Read Brightness value <CR>*bri=?#<CR> Write Color + <CR>*color=+#<CR>...
Seite 25
Function Type Operation ASCII Picture Setting Write 4 Corners Top-Left - X Decrease <CR>*cornerfittlx=-#<CR> Write 4 Corners Top-Left - X Increase <CR>*cornerfittlx=+#<CR> Read 4 Corners Top-Left - X Status <CR>*cornerfittlx=?#<CR> Write 4 Corners Top-Left - Y Decrease <CR>*cornerfittly=-#<CR> Write 4 Corners Top-Left - Y Increase <CR>*cornerfittly=+#<CR>...
Seite 26
Function Type Operation ASCII Operation Set- Write Projector Position-Front Table <CR>*pp=FT#<CR> tings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
Seite 27
Function Type Operation ASCII Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> Read Blank Status <CR>*blank=?#<CR>...
Seite 28
Function Type Operation ASCII Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR>...
Seite 29
Function Type Operation ASCII Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR>...
LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 33 INST? LU9255 list query Projector name Returns the name set in [PROJECTOR NAME] of [NET- NAME? xxxxx query WORK SETUP]...
Seite 31
Remark Details Return String Manufacturer INF1? BenQ Returns manufacturer name name query Model name que- INF2? LU9255 Returns moder name Other informa- INF0? xxxxx Returns information such as version number tion queries Class information CLASS? Returns class for PJLink query Note: RS-232 baud rate options are 2400, 4800, 9600, 14400, 19200, 38400, 57600 and 115200 (Default : 115200).
Seite 57
ASCII 功能 類型 操作 Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> 繁 體 Read Lan F/W Version <CR>*lanfwversion=?#<CR> 中 Read MCU F/W Version <CR>*mcufwversion=?#<CR> 文 Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR>...
Seite 58
ASCII 功能 類型 操作 Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> 繁 體 Read Mac Address <CR>*macaddr=?#<CR> 中 Write High Altitude mode on <CR>*Highaltitude=on#<CR> 文 Write High Altitude mode off <CR>*Highaltitude=off#<CR>...
Seite 59
ASCII 功能 類型 操作 Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> 繁 體 Read Get Blue Offset value <CR>*BOffset=?#<CR> 中 Write Primary Color <CR>*primcr=value#<CR> 文 Read Primary Color Status <CR>*primcr=?#<CR>...
Light source sta- LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 INST? LU9255 list query 33 34 Projector name Returns the name set in [PROJECTOR NAME] of [NET- NAME? xxxxx query...
Seite 61
指令 控制詳細資訊 備註 傳回字串 Manufacturer INF1? BenQ Returns manufacturer name name query 繁 Model name que- INF2? LU9255 Returns moder name 體 中 Other informa- INF0? xxxxx Returns information such as version number 文 tion queries Class information CLASS? Returns class for PJLink query 注意事項:...
Seite 69
OVERSCAN 按下可选择过扫描模式。 FREEZE 冻结投影图像。 LAMP MODE 按下显示 OSD 菜单以选择所所需光源模式。 3D MODE 按下可显示 3D 设置菜单。 INFO. 按下可显示信息菜单。 简 LIGHT 体 按下可打开遥控器背光。 中 CLEAR 文 清除分配给所有投影机的 ID 设置。 按住 CLEAR 和 ID SET 五秒。 LED 闪烁三下, 之后 ID 设置被清除。 SHUTTER 在此投影机中没有这项功能。 ID SET •...
Seite 84
ASCII 功能 类型 操作 Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=5#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=5#<CR> 简 Read Brightness value <CR>*bri=?#<CR>...
Seite 85
ASCII 功能 类型 操作 Picture Setting Write 4 Corners Top-Left - X Decrease <CR>*cornerfittlx=-#<CR> Write 4 Corners Top-Left - X Increase <CR>*cornerfittlx=+#<CR> Read 4 Corners Top-Left - X Status <CR>*cornerfittlx=?#<CR> Write 4 Corners Top-Left - Y Decrease <CR>*cornerfittly=-#<CR> Write 4 Corners Top-Left - Y Increase <CR>*cornerfittly=+#<CR>...
Seite 86
ASCII 功能 类型 操作 Operation Set- Write Projector Position-Front Table <CR>*pp=FT#<CR> tings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
Seite 87
ASCII 功能 类型 操作 Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> 简 Read Blank Status <CR>*blank=?#<CR>...
Seite 88
ASCII 功能 类型 操作 Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR>...
Seite 89
ASCII 功能 类型 操作 Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR>...
LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 33 INST? LU9255 list query Projector name Returns the name set in [PROJECTOR NAME] of [NET- NAME? xxxxx query WORK SETUP]...
Seite 91
命令 控制详细信息 备注 返回字符串 Manufacturer INF1? BenQ Returns manufacturer name name query Model name que- INF2? LU9255 Returns moder name Other informa- INF0? xxxxx Returns information such as version number tion queries Class information CLASS? Returns class for PJLink 简...
Seite 92
Dimension de la lentille ..............110 Commande RS232 ................111 Affectation des broches RS232 ................111 Port série RS232 avec un câble croisé ..............111 PJLink ........................119 Veuillez consulter le site Web ci-dessous pour obtenir la dernière version du Manuel d’utilisation/Guide d’installation. http://business-display.benq.com/ V1.00...
Notice Informations sur le laser Ce symbole indique que le non respect des instructions entraîne un risque potentiel d'exposition des yeux au rayonnement laser. y Classe laser (pour les États-Unis) Ce Produit Laser est désigné Classe 3R pendant toutes les procédures de fonctionnement et respecte la norme IEC/EN 60825-1:2007.
Informations sur le refroidissement Prévoyez au moins 50 cm (19,7 po) de dégagement autour de la sortie de ventilation. Veillez à ce qu'aucun objet ne bloque l'entrée d'air à moins de 30 cm (11,8 po). La sortie doit être à au moins 1 m des entrées d'autres projecteurs. Entrée d'air Entrée d'air Sortie d'air...
Seite 95
• Prévoyez au moins 50 cm de dégagement autour de la sortie de ventilation. Minimum 50 cm Minimum 50 cm Minimum 50 cm (19,69 po) (19,69 po) (19,69 po) Minimum 50 cm (19,69 po) Minimum 10 cm (3,94 po) Minimum 50 cm (19,69 po) Minimum 30 cm (11,81 po)
Assurez-vous que le port est valide avant de connecter une télécommande filaire. La télécommande peut être endommagée en cas d’utilisation d'un port non valide, ex. une télécommande filaire connectée pour déclencher une sortie. Pour plus d’informations sur la mise à niveau du firmware via Lan, veuillez contacter le service BenQ.
Télécommande ON / OFF Permet de faire basculer le projecteur entre les modes veille et activé. KEYSTONE+/KEYSTONE- Permet de corriger manuellement la déformation des images due à l’angle de projection. VOLUME +/VOLUME - Augmente/diminue le volume du projecteur. QUICK INSTALL Affiche le menu OSD Installation rapide.
Seite 99
OVERSCAN Appuyez pour sélectionner le mode surbalayage. FREEZE Met en pause l’image projetée. LAMP MODE Appuyez pour afficher le menu OSD pour sélectionner le mode lumineux souhaité. 3D MODE Appuyez pour afficher le menu de configuration 3D. INFO. Appuyez sur pour afficher le menu INFORMATIONS. LIGHT Appuyez pour ouvrir le rétroéclairage de la télécommande.
Installation Attention : Pour éviter d’endommager les puces DLP, ne dirigez jamais un rayon laser à haute puissance dans l’objectif de projection. Installation et retrait de la lentille en option Attention : • Ne secouez pas et n’exercez pas une pression excessive sur le projecteur ou les composants de lentilles car ils contiennent des pièces de précision.
Seite 101
y Retirer l’objectif existant du projecteur 1. Poussez le bouton LIBÉRATION DE L’OBJECTIF jusqu’à la position déverrouillée. 2. Saisissez l’objectif. 3. Tournez l’objectif dans le sens inverse des aiguilles d’une montre. L’objectif existant est désengagé. 4. Retirez lentement l’objectif existant.
Horizontal : -5 %-5 % Projection table *** « A » est basé sur la position maximale de compensation de décalage d’objectif de 55 % • LU9255 Le rapport d’aspect est 16:10 est l’image projetée est en 16:10. Remarque : Pour optimiser la qualité...
Seite 103
13,46 17,23 Remarque : • Pour des instructions plus visualisées, veuillez accéder au site Web du calculateur BenQ http://projectorcalculator. benq.com/. • L’installation au plafond doit être réalisée par un professionnel qualifié. Contactez votre revendeur pour plus d’informations. Il n’est pas conseillé d’installer le projecteur vous-même.
Plage de décalage de l’objectif y Plage réglable de décalage de l’objectif La plage réglable pour le décalage de l’objectif est présentée dans le tableau ci-dessous et soumise aux conditions indiquées. • LU9255 Position normale de projection Décalage Bureau-Projection avant...
Seite 105
y Installation sur bureau Centre de l’écran Plage de décalage 0.05H Remarque : • Les illustrations s’appliquent uniquement à l’objectif standard.
Indicateur DEL y Message système Alim- Tempér- Éclairage Filtre Statut et description entation ature Orange Veille Vert cligno- Allumage tant Vert Fonctionnement Normal Orange Refroidissement normal de mise hors tension clignotant Rouge Rouge Rouge Téléchargement Vert Rouge Échec du démarrage de l’onde entretenue Rouge Vert Échec du démarrage de la roue au phosphore...
Seite 107
y Messages d’erreurs des lampes Alim- Tempér- Éclairage Filtre Statut et description entation ature Rouge Erreur lampe 1 en fonctionnement normal Rouge Erreur lampe 2 en fonctionnement normal Rouge Rouge Dysfonctionnement des deux lampes Rouge La lampe n’est pas allumée Clignotante y Messages d’erreurs thermiques Alim-...
Seite 108
Alim- Tempér- Éclairage Filtre Statut et description entation ature Vert Vert Erreur capteur thermique 2 en court-circuit Clignotante Vert Vert Erreur connexion I2C CI thermique 2 Clignotante Clignotante Erreur température 3 (dépassement de la limite de Vert Rouge Rouge température) Rouge Vert Rouge...
Schéma d'installation au plafond N° Support de plafond BenQ CMG6 (5A.JHS10.001) Matériau Acier Poids 10,5 kg (23,1 lb) Dimensions (L x H x P) 410 x 641 x 360 mm (16,14" x 25,24" x 14,17") Longueur 491 mm ~ 641 mm Angle d’inclinaison...
Dimension de la lentille Lentille en option (Standard : LS2SD2) Lentille en option (Zoom large : LS2ST1) Lentille en option (Zoom long : LS2LT2) Lentille en option (Projection semi-longue : LS2LT1) Objectif en option Objectif en option (Projection semi : LS2ST4) (Projection court : LS2ST2)
Commande RS232 Affectation des broches RS232 N° Série N° Série Court avec broche 8 Court avec broche 7 Terre Port série RS232 avec un câble croisé Function Type Operation ASCII Power Write Power On <CR>*pow=on#<CR> Write Power off <CR>*pow=off#<CR> Read Power Status <CR>*pow=?#<CR>...
Seite 113
Function Type Operation ASCII Audio Source Write Audio pass Through off <CR>*audiosour=off#<CR> Select Write Audio-Computer1 <CR>*audiosour=RGB#<CR> Write Audio-Video/S-Video <CR>*audiosour=vid#<CR> Write Audio-HDMI <CR>*audiosour=hdmi#<CR> Write Audio-HDMI2 <CR>*audiosour=hdmi2#<CR> Read Audio pass Status <CR>*audiosour=?#<CR> Picture Mode Write Presentation <CR>*appmod=preset#<CR> Write sRGB <CR>*appmod=srgb#<CR> Write Bright <CR>*appmod=bright#<CR>...
Seite 114
Function Type Operation ASCII Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=5#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=5#<CR> Read Brightness value <CR>*bri=?#<CR> Write Color + <CR>*color=+#<CR>...
Seite 115
Function Type Operation ASCII Picture Setting Write 4 Corners Top-Left - X Decrease <CR>*cornerfittlx=-#<CR> Write 4 Corners Top-Left - X Increase <CR>*cornerfittlx=+#<CR> Read 4 Corners Top-Left - X Status <CR>*cornerfittlx=?#<CR> Write 4 Corners Top-Left - Y Decrease <CR>*cornerfittly=-#<CR> Write 4 Corners Top-Left - Y Increase <CR>*cornerfittly=+#<CR>...
Seite 116
Function Type Operation ASCII Operation Set- Write Projector Position-Front Table <CR>*pp=FT#<CR> tings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
Seite 117
Function Type Operation ASCII Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> Read Blank Status <CR>*blank=?#<CR>...
Seite 118
Function Type Operation ASCII Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR>...
Seite 119
Function Type Operation ASCII Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR>...
5th byte Return 0 Indicates other errors, and 6th byte returns 0 - 2 Light source sta- LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 33 INST? LU9255 list query...
Seite 121
WORK SETUP] Manufacturer INF1? BenQ Returns manufacturer name name query Model name que- INF2? LU9255 Returns moder name Other informa- INF0? xxxxx Returns information such as version number tion queries Class information CLASS? Returns class for PJLink query Remarque : Les options de débit en bauds RS-232 sont 2400, 4800, 9600, 14400, 19200, 38400, 57600 et 115200...
Seite 122
LED-Anzeige ......................135 Projektionsmaße ................138 Diagramm zur Deckenmontage ............139 Größen- und Winkelanpassung ................139 Objektivabmessungen ..............140 RS-232-Befehl ..................141 RS-232-Pinbelegung ....................141 Serieller RS-232-Anschluss mit gekreuztem Kabel ..........141 PJLink ........................149 Auf der nachstehenden Webseite finden Sie die aktuellste Version der Bedienungsanleitung / Installationsanleitung. http://business-display.benq.com/ V1.00...
Notice Hinweis zum Laser Dieses Symbol zeigt an, dass Augen möglicherweise Laserstrahlung ausgesetzt werden könnten, falls die Anweisungen nicht strikt befolgt werden. y Laserklasse (USA) Dieses Laserprodukt ist während aller Betriebsverfahren als Gerät der Klasse 3R zugewiesen und stimmt mit IEC/EN 60825-1:2007 überein. (Weltweit) Dieses Laserprodukt ist während aller Betriebsverfahren als Gerät der Klasse 1 zugewiesen und stimmt mit IEC/EN 60825-1:2014 überein.
Hinweis zu Kühlung Halten Sie einen Freiraum von mindestens 50 cm rund um die Abluftöffnungen ein. Achten sie darauf, dass die Zuluftöffnungen in einem Umkreis von 30 cm nicht blockiert werden. Die Abluftöffnungen müssen mindestens 1 m von Zuluftöffnungen anderer Projektoren entfernt sein.
Seite 125
• Halten Sie einen Freiraum von mindestens 50 cm rund um die Abluftöffnungen ein. Mindestens 50 cm Mindestens 50 cm Mindestens 50 cm (19,69 Zoll) (19,69 Zoll) (19,69 Zoll) Mindestens 50 cm (19,69 Zoll) Mindestens 10 cm (3,94 Zoll) Mindestens 50 cm (19,69 Zoll) Mindestens 30 cm (11,81 Zoll)
Stellen Sie sicher, dass der Port gültig ist, bevor Sie eine kabelgebundene Fernbedienung einstecken. Die Fernbedienung könnte im Falle eines ungültigen Ports beschädigt werden, bspw. bei Anschluss einer kabelgebundenen Fernbedienung an den Auslöserausgang. Weitere Informationen zur Aktualisierung der Firmware per WLAN erhalten Sie vom BenQ-Kundendienst.
Remote control ON / OFF Schaltet zwischen Bereitschaftsmodus und Betriebsmodus des Projektors KEYSTONE+/KEYSTONE- Korrigiert manuell Bildverzerrungen, die von einer abgewinkelten Projektion stammen. VOLUME +/VOLUME - Erhöht/verringert die Projektorlautstärke. QUICK INSTALL Ruft das Schnellinstallation-Menü auf. MUTE Schaltet die Tonausgabe des Projektors ein und aus. Pfeiltasten (▲...
Seite 129
OVERSCAN Zur Auswahl des Overscan-Modus drücken. FREEZE Zeigt das projizierte Bild als Standbild an. LAMP MODE Zum Einblenden des OSD-Menüs drücken; wählen Sie dann den gewünschten Lichtmodus. 3D MODE Zur Anzeige des 3D-Einrichtungsmenüs drücken. INFO. Zur Anzeige des INFORMATIONEN-Menüs drücken. LIGHT Zum Aktivieren der Fernbedienungshintergrundbeleuchtung drücken.
Installation Achtung: Vermeiden Sie Schäden an DLP-Chips, indem Sie niemals einen hochleistungsfähigen Laserstrahl auf das Projektionsobjektiv richten. Optionales Objektiv installieren oder entfernen Achtung: • Sie dürfen Projektor und Objektivkomponenten weder schütteln noch übermäßigem Druck aussetzen, da sie Präzisionsteile enthalten. • Achten Sie vor dem Entfernen oder Installieren des Objektivs darauf, den Projektor auszuschalten;...
y Vorhandenes Objektiv vom Projektor entfernen 1. Drücken Sie die LENS RELEASE-Taste in die Freigabeposition. 2. Greifen Sie das Objektiv. 3. Drehen Sie das Objektiv gegen den Uhrzeigersinn. Das vorhandene Objektiv wird gelöst. 4. Ziehen Sie das vorhandene Objektiv langsam heraus.
WUXGA: 1,25-1,6 Horizontal: -5%-5% Projection table *** „A“ basiert auf der maximalen Objektivversatzposition 55 % • LU9255 Das Seitenverhältnis beträgt 16:10 und das projizierte Bild ist 16:10. Hinweis: Zur Optimierung der Projektionsqualität sollten Sie Bilder in einem Bereich ohne Grauskala projizieren.
Seite 133
13,46 17,23 Hinweis: • Weitere visualisierte Anleitungen finden Sie auf der Webseite des BenQ-Rechners: http://projectorcalculator. benq.com/. • Deckenmontage muss von einem qualifizierten Experten durchgeführt werden. Wenden Sie sich für weitere Informationen an Ihren Händler. Sie sollten den Projektor nicht eigenständig installieren.
Objektivversatzbereich y Verstellbarer Objektivversatzbereich Der verstellbare Objektivversatzbereich ist nachstehend erfasst und unterliegt den aufgelisteten Bedingungen. • LU9255 Normale Projektionsposition Vertikaler Tisch/Frontprojektion Versatz Maximal 0,55V Höhe des projizierten Bildes Vertikaler Versatz Maximal 0,05H 0,05H 0,15V Deckenmontage/Frontprojektion Breite des projizierten Bildes Vertikaler Versatz Höhe des projizierten Bildes...
Seite 135
y Desktop-Installation Leinwandmitte Versandbereich 0.05H Hinweis: • Die Zeichnungen gelten nur für das Standardobjektiv.
Seite 137
y Lampenfehlermeldungen Ein-/ Temp Licht Filter Status und Beschreibung Austaste Lampe-1-Fehler im Normalbetrieb Lampe-2-Fehler im Normalbetrieb Fehler beider Lampen Lampe leuchtet nicht Blinkt y Temperaturfehlermeldungen Ein-/ Temp Licht Filter Status und Beschreibung Austaste Lüfter-1-Fehler (die tatsächliche Lüftergeschwindigkeit entspricht nicht der gewünschten Geschwindigkeit) Lüfter-2-Fehler (die tatsächliche Lüftergeschwindigkeit Blinkt entspricht nicht der gewünschten Geschwindigkeit)
Diagramm zur Deckenmontage BenQ-Deckenhalterung CMG6 (5A.JHS10.001) Material Stahl Gewicht 10,5 kg Abmessungen (B x H x T) 410 x 641 x 360 mm Länge 491 bis 641 mm Neigungswinkel Schwenken: ±5° Vertikal: +5°/-25° Horizontal: ±5° Last 40 kg Schraubentyp M4, M5, M6, M8...
RS-232-Befehl RS-232-Pinbelegung Seriell Seriell Kurz mit Pin 8 Kurz mit Pin 7 Erde Serieller RS-232-Anschluss mit gekreuztem Kabel Funktion Bedienung ASCII Power Write Power On <CR>*pow=on#<CR> Write Power off <CR>*pow=off#<CR> Read Power Status <CR>*pow=?#<CR> Source Selec- Write COMPUTER/YPbPr <CR>*sour=RGB#<CR> tion Write COMPUTER 2/YPbPr2 <CR>*sour=RGB2#<CR>...
Seite 144
Funktion Bedienung ASCII Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=5#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=5#<CR> Read Brightness value <CR>*bri=?#<CR> Write Color + <CR>*color=+#<CR>...
Seite 145
Funktion Bedienung ASCII Picture Setting Write 4 Corners Top-Left - X Decrease <CR>*cornerfittlx=-#<CR> Write 4 Corners Top-Left - X Increase <CR>*cornerfittlx=+#<CR> Read 4 Corners Top-Left - X Status <CR>*cornerfittlx=?#<CR> Write 4 Corners Top-Left - Y Decrease <CR>*cornerfittly=-#<CR> Write 4 Corners Top-Left - Y Increase <CR>*cornerfittly=+#<CR>...
Seite 146
Funktion Bedienung ASCII Operation Set- Write Projector Position-Front Table <CR>*pp=FT#<CR> tings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
Seite 147
Funktion Bedienung ASCII Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> Read Blank Status <CR>*blank=?#<CR> Write Freeze On <CR>*freeze=on#<CR>...
Seite 148
Funktion Bedienung ASCII Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR> Read High Altitude mode status <CR>*Highaltitude=?#<CR>...
Seite 149
Funktion Bedienung ASCII Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR>...
5th byte Return 0 Indicates other errors, and 6th byte returns 0 - 2 Light source sta- LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 33 INST? LU9255 list query...
Seite 151
WORK SETUP] Manufacturer INF1? BenQ Returns manufacturer name name query Model name que- INF2? LU9255 Returns moder name Other informa- INF0? xxxxx Returns information such as version number tion queries Class information CLASS? Returns class for PJLink query Hinweis: RS-232 baud rate options are 2400, 4800, 9600, 14400, 19200, 38400, 57600 and 115200 (Default : 115200).
Seite 152
Comando RS232 ................171 Assegnazione dei pin RS232 ................... 171 Porta seriale RS232 con un cavo crossover ............171 PJLink ........................179 Visitare il sito web di seguito per la versione più recente del manuale d'uso/della guida all'installazione. http://business-display.benq.com/ V1.00...
Notice Avviso sul laser Questo simbolo indica che c’è un potenziale rischio di esposizione dell'occhio alle radiazioni laser se non sono seguite le istruzioni. y Classe laser (Per gli Stati Uniti) Questo prodotto laser è designato come Classe 3R durante tutte le procedure operative ed è...
Avviso sul raffreddamento Lasciare almeno 50 cm (19,7 pollici) di spazio attorno allo scarico dell’aria. Assicurarsi che nessun oggetto blocchi le prese d’aria entro 30 cm (11,8 pollici). Tenere lo scarico dell’aria ad almeno 1 di distanza dalle prese d’aria di altri proiettori. Presa d'aria Presa d'aria Scarico dell’aria...
Seite 155
• Lasciare almeno 50 cm di spazio attorno allo scarico dell’aria. Minimo 50 cm Minimo 50 cm Minimo 50 cm (19,69 pollici) (19,69 pollici) (19,69 pollici) Minimo 50 cm (19,69 pollici) Minimo 10 cm (3,94 pollici) Minimo 50 cm (19,69 pollici) Minimo 30 cm (11,81 pollici) Minimo 50 cm...
Batterie Guida di installazione antipolvere Cavo da VESA Cavo d’alimentazione VGA cable a BNC a 3 pin Specifiche tecniche LU9255 Sistema di proiezione Chip singolo DMD WUXGA 0,67 DLP Risoluzione nativa 1920*1200 pixel, 16:10 Sorgente luminosa Diodi laser Consumo energetico 1000 W (modalità...
Assicurarsi che la porta sia valida prima di inserire un telecomando cablato. Il telecomando potrebbe essere danneggiato se la porta non è valida, ad esempio se il telecomando cablato è collegato alla porta Trigger. Per ulteriori informazioni sull'aggiornamento del firmware tramite LAN, contattare il servizio BenQ.
Telecomando ON / OFF Fa passare il proiettore tra la modalità di standby e di accensione. KEYSTONE+/KEYSTONE- Correzione manuale della distorsione delle immagini provocata dalla proiezione inclinata. VOLUME +/VOLUME - Aumenta/diminuisce il volume del proiettore. QUICK INSTALL Visualizza il menu OSD Installazione rapida. MUTE Attiva e disattiva l’audio del proiettore.
Seite 159
OVERSCAN Premere per selezionare la modalità overscan. FREEZE Blocca l’immagine proiettata. LAMP MODE Premere per visualizzare il menu OSD per selezionare la modalità di illuminazione voluta. 3D MODE Premere per visualizzare il menu di impostazione 3D. INFO. Premere per visualizzare il menu INFORMAZIONI. LIGHT Premere per accendere l’illuminazione del telecomando.
Installazione Attenzione: Per evitare di danneggiare i chip DLP, non puntare mai un fascio laser ad alta energia nell’obiettivo del proiettore. Installazione o rimozione dell'obbiettivo optional Attenzione: • Non scuotere né applicare pressione eccessiva sul proiettore o sui componenti dell'obbiettivo perché il proiettore ed i componenti dell'obbiettivo contengono parti di precisione.
Seite 161
y Rimozione dell’obiettivo esistente dal proiettore 1. Spingere il tasto LENSE RELEASE in posizione di sblocco. 2. Afferrare l’obiettivo. 3. Ruotare l’obiettivo in senso antiorario. L’obiettivo si sgancerà. 4. Estrarre lentamente l’obiettivo.
Orizzontale: -5%-5% Projection table *** "A" si basa sulla posizione di offset spostamento obiettivo massimo 55% • LU9255 Il formato dello schermo è 16:10 e l’immagine proiettata è 16:10. Nota: Per ottimizzare la qualità di proiezione, si consiglia di proiettare immagini in un’area priva di scala di grigi.
Seite 163
17,23 Nota: • Per ulteriori istruzioni, visitare il sito web BenQ Calculator all'indirizzo http://projectorcalculator.benq.com/. • L'installazione a soffitto deve essere effettuata da un professionista qualificato. Rivolgersi al rivenditore per ulteriori informazioni. Si consiglia di non installare il proiettore da soli.
Intervallo di spostamento obiettivo y Gamma di regolazione dello spostamento dell'obiettivo La gamma di regolazione dello spostamento dell'obiettivo è riportata di seguito e soggetta alle condizioni elencate. • LU9255 Posizione di proiezione normale Spostamento Proiezione tavolo - frontale verticale Max 0,55V Altezza dell’immagine proiettata...
y Messaggio di sistema Alime- Temp Light Filtro Stato e descrizione ntazione Arancione Stand-by Lampeg- giante in Accensione verde Verde Funzionamento normale Lampeg- giante in Raffreddamento di spegnimento normale arancione Rosso Rosso Rosso Download Verde Rosso Impossibile avviare CW Lampeg- Verde giante in Impossibile avviare ruota fosforo...
Seite 167
y Messaggi di errore lampada Alime- Temp Light Filtro Stato e descrizione ntazione Rosso Errore Lamp1 durante funzionamento normale Rosso Errore Lamp2 durante funzionamento normale Rosso Rosso Guasto entrambe lampade Rosso Lampeggi- Lampada non accesa ante y Messaggi di errore termico Alime- Temp Light...
Seite 168
Alime- Temp Light Filtro Stato e descrizione ntazione Verde Verde Lampeggi- IC termico 1 Errore connessione I2C ante Verde Lampeggi- Rosso Errore temperatura 2 (temperatura sopra il limite) ante Verde Rosso Lampeggi- Lampeggi- Errore apertura sensore termico 2 ante ante Verde Lampeggi- Verde...
Schema di installazione a soffitto Supporto a soffitto BenQ CMG6 (5A.JHS10.001) Materiale Acciaio Peso 10,5 kg (23,1 lbs) Dimensioni (L x A x P) 410 x 641 x 360 mm (16,14" x 25,24" x 14,17") Lunghezza 491 mm ~ 641 mm Angolo di inclinazione Rotazione: ±5°...
Comando RS232 Assegnazione dei pin RS232 Seriale Seriale Corto con pin 8 Corto con pin 7 Terra Porta seriale RS232 con un cavo crossover Funzione Tipo Funzionamento ASCII Power Write Power On <CR>*pow=on#<CR> Write Power off <CR>*pow=off#<CR> Read Power Status <CR>*pow=?#<CR>...
Seite 173
Funzione Tipo Funzionamento ASCII Audio Source Write Audio pass Through off <CR>*audiosour=off#<CR> Select Write Audio-Computer1 <CR>*audiosour=RGB#<CR> Write Audio-Video/S-Video <CR>*audiosour=vid#<CR> Write Audio-HDMI <CR>*audiosour=hdmi#<CR> Write Audio-HDMI2 <CR>*audiosour=hdmi2#<CR> Read Audio pass Status <CR>*audiosour=?#<CR> Picture Mode Write Presentation <CR>*appmod=preset#<CR> Write sRGB <CR>*appmod=srgb#<CR> Write Bright <CR>*appmod=bright#<CR>...
Seite 174
Funzione Tipo Funzionamento ASCII Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=5#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=5#<CR> Read Brightness value <CR>*bri=?#<CR> Write Color + <CR>*color=+#<CR>...
Seite 175
Funzione Tipo Funzionamento ASCII Picture Setting Write 4 Corners Top-Left - X Decrease <CR>*cornerfittlx=-#<CR> Write 4 Corners Top-Left - X Increase <CR>*cornerfittlx=+#<CR> Read 4 Corners Top-Left - X Status <CR>*cornerfittlx=?#<CR> Write 4 Corners Top-Left - Y Decrease <CR>*cornerfittly=-#<CR> Write 4 Corners Top-Left - Y Increase <CR>*cornerfittly=+#<CR>...
Seite 176
Funzione Tipo Funzionamento ASCII Operation Set- Write Projector Position-Front Table <CR>*pp=FT#<CR> tings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
Seite 177
Funzione Tipo Funzionamento ASCII Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> Read Blank Status <CR>*blank=?#<CR>...
Seite 178
Funzione Tipo Funzionamento ASCII Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR>...
Seite 179
Funzione Tipo Funzionamento ASCII Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR>...
5th byte Return 0 Indicates other errors, and 6th byte returns 0 - 2 Light source sta- LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 33 INST? LU9255 list query...
Seite 181
WORK SETUP] Manufacturer INF1? BenQ Returns manufacturer name name query Model name que- INF2? LU9255 Returns moder name Other informa- INF0? xxxxx Returns information such as version number tion queries Class information CLASS? Returns class for PJLink query...
Seite 182
Подстройка под размер и угол ................199 Размеры объективов ..............200 Передача сигналов управления по RS-232 ......201 Назначение контактов RS-232 ................201 Последовательный порт RS-232 с перекрестным кабелем ......201 PJLink ........................209 Последняя версия руководства пользователя и руководства по установке доступна на веб-сайте ниже. http://business-display.benq.com/ V1.00...
Notice Примечание относительно лазера Этот символ указывает на потенциальную опасность воздействия на глаза лазерного излучения в случае несоблюдения инструкций. y Класс лазера (для США) Данное лазерное устройство отнесено к классу 3R во всех инструкциях по эксплуатации и соответствует стандарту IEC/EN 60825- 1:2007.
Примечание относительно охлаждения Оставьте как минимум 50 см (19,7 дюйма) свободного пространства вокруг вентиляционных отверстий. На расстоянии 30 см (11,8 дюйма) от проектора не должно быть никаких предметов, блокирующих поступление воздуха. Выпускные отверстия должны находиться на расстоянии не менее 1 метра от впускных...
Seite 185
• Оставьте как минимум 50 см свободного пространства вокруг вентиляционных отверстий. Минимум 50 см Минимум 50 см Минимум 50 см (19,69 дюйма) (19,69 дюйма) (19,69 дюйма) Минимум 50 см (19,69 дюйма) Минимум 10 см (3,94 дюйма) Минимум 50 см (19,69 дюйма) Минимум...
Комплект поставки Стандартная комплектация VESA - BNC Спецификация LU9255 Проекционная система DLP Single 0.67 WUXGA DMD Chip Собственное разрешение 1920*1200 пикселей, 16:10 Источник света Лазерные диоды Потребляемая мощность 1000 Вт (обычный режим) / 800 Вт (экономичный режим) Размеры 525 x 216 x 470 мм...
(±1,5 В) и защитой от короткого замыкания. Внимание! Подключать проводной пульт ДУ допускается только к соответствующему порту. Пульт ДУ может быть поврежден при подключении к неподходящему порту, например, к триггерному выходу. За дополнительной информацией об обновлении встроенного ПО по LAN обращайтесь сервисный центр BenQ.
Remote control ON / OFF Переключение режимов ожидания и включения проектора. KEYSTONE+/KEYSTONE- Ручная коррекция искажений изображения, возникших в результате проекции под углом. VOLUME +/VOLUME - Увеличение/уменьшение громкости проектора. QUICK INSTALL На экран выводится меню Быстрая установка. MUTE Включение и выключение звука проектора. Кнопки...
Seite 189
OVERSCAN Нажмите для настройки нерабочей области FREEZE Стоп-кадр проецируемого изображения. LAMP MODE Нажмите для открытия экранного меню и выбора необходимого режима света. 3D MODE Нажмите для открытия меню настройки 3D. INFO. Нажмите для вызова меню «ИНФОРМАЦИЯ». LIGHT Нажмите для включения подсветки пульта ДУ. CLEAR Очистка...
Установка Внимание! Во избежание повреждения DLP-кристалла не направляйте мощный лазерный луч на проекционный объектив. Установка и снятие дополнительного объектива Внимание! • Не трясите и не давите чрезмерно на проектор и компоненты объектива, так как они содержат прецизионные детали. • Перед снятием или установкой объектива обязательно отключите проектор, дождитесь остановки...
Seite 191
y Снятие имеющегося объектива с проектора 1. Нажмите кнопку ОТСОЕДИНЕНИЕ ОБЪЕКТИВА в положение разблокировки. 2. Возьмите объектив пальцами. 3. Начните вращать его против часовой стрелки. Объектив будет отсоединен.. 4. Медленно вытащите его.
WUXGA: 1,25-1,6 По горизонтали: -5%-5% Projection table *** "А" указано для максимального положения смещения (сдвига) объектива в 55% • LU9255 Соотношение сторон экрана составляет 16:10, а проецируемого изображения – 16:10. Примечание: Для оптимизации качества проецирования рекомендуется проецировать изображения в зоне, не...
Seite 193
3,702 8,29 11,85 13,46 17,23 Примечание: • Визуализированные инструкции доступны на веб-сайте калькулятора BenQ по адресу http:// projectorcalculator.benq.com/ • Потолочный монтаж должен выполняться квалифицированным специалистом. Обратитесь к своему дилеру за дополнительной информацией. Не рекомендуется устанавливать проектор самостоятельно. • Используйте проектор только на твердой, ровной поверхности. Падение проектора может стать...
Диапазон смещения объектива y Диапазон подстройки смещения объектива Диапазон подстройки смещения объектива приведен в таблице ниже и зависит от указанных условий. • LU9255 Вертикальное Нормальное положение проекции Стол – фронтальная смещение Не более проекция 0,55 В Высота проецируемого изображения Вертикальное смещение...
Seite 195
y Установка на столе Центр экрана Диапазон смещения 0.05H Примечание: • Чертежи распространяются только на стандартный объектив.
Светодиодный индикатор y Системное сообщение Темпер- Подсв- Питание Фильтр Состояние и описание атура етка Оранжевый Ожидание Мигает Включение питания зеленым Зеленый Нормальный режим работы Мигает Нормальное охлаждение при отключении питания оранжевым Красный Красный Красный Загрузка Зеленый Красный Ошибка запуска CW Мигает...
Seite 197
y Сообщения ошибок лампы Темпер- Подсв- Питание Фильтр Состояние и описание атура етка Ошибка Лампы 1 при работе в нормальных Красный условиях Ошибка Лампы 2 при работе в нормальных Красный условиях Красный Красный Сбой обеих ламп Красный Лампа не загорается Мигает...
Seite 198
Темпер- Подсв- Питание Фильтр Состояние и описание атура етка Зеленый Красный Ошибка открытия Термодатчика 2 Мигает Мигает Зеленый Зеленый Короткое замыкание Термодатчика 2 Мигает Зеленый Зеленый Ошибка подключения Термального IC №2 I2C Мигает Мигает Ошибка Температуры 3 (превышены Зеленый Красный Красный...
Схема монтажа на потолке № Кронштейн BenQ для крепления на потолке CMG6 (5A.JHS10.001) Материал Сталь Вес 10,5 кг Размеры (Ш x В x Г) 410 x 641 x 360 мм Длина 491~641 мм Угол наклона Поворот: ±5° По вертикали: +5°/-25°...
Передача сигналов управления по RS-232 Назначение контактов RS-232 № Последовательный № Последовательный Закорочен с контактом 8 Закорочен с контактом 7 Заземление Последовательный порт RS-232 с перекрестным кабелем Function Type Operation ASCII Power Write Power On <CR>*pow=on#<CR> Write Power off <CR>*pow=off#<CR> Read Power Status <CR>*pow=?#<CR>...
Seite 203
Function Type Operation ASCII Audio Source Write Audio pass Through off <CR>*audiosour=off#<CR> Select Write Audio-Computer1 <CR>*audiosour=RGB#<CR> Write Audio-Video/S-Video <CR>*audiosour=vid#<CR> Write Audio-HDMI <CR>*audiosour=hdmi#<CR> Write Audio-HDMI2 <CR>*audiosour=hdmi2#<CR> Read Audio pass Status <CR>*audiosour=?#<CR> Picture Mode Write Presentation <CR>*appmod=preset#<CR> Write sRGB <CR>*appmod=srgb#<CR> Write Bright <CR>*appmod=bright#<CR>...
Seite 204
Function Type Operation ASCII Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=5#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=5#<CR> Read Brightness value <CR>*bri=?#<CR> Write Color + <CR>*color=+#<CR>...
Seite 205
Function Type Operation ASCII Picture Setting Write 4 Corners Top-Left - X Decrease <CR>*cornerfittlx=-#<CR> Write 4 Corners Top-Left - X Increase <CR>*cornerfittlx=+#<CR> Read 4 Corners Top-Left - X Status <CR>*cornerfittlx=?#<CR> Write 4 Corners Top-Left - Y Decrease <CR>*cornerfittly=-#<CR> Write 4 Corners Top-Left - Y Increase <CR>*cornerfittly=+#<CR>...
Seite 206
Function Type Operation ASCII Operation Set- Write Projector Position-Front Table <CR>*pp=FT#<CR> tings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
Seite 207
Function Type Operation ASCII Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> Read Blank Status <CR>*blank=?#<CR>...
Seite 208
Function Type Operation ASCII Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR>...
Seite 209
Function Type Operation ASCII Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR>...
PJLink y Протокол PJLink Сетевая функция данного проектора поддерживает PJLink класса 1, а протокол PJLink может использоваться для выполнения операций по настройке проектора и запросу состояния проектора с компьютера. y Сигналы управления В следующей таблице представлены команды протокола PJLink, которые можно использовать...
Seite 211
Описание Параметр/ Команда сигнала Возврат Примечание управления строки Input selection 11 12 21 31 32 33 INST? LU9255 list query Projector name Returns the name set in [PROJECTOR NAME] of [NET- NAME? xxxxx query WORK SETUP] Manufacturer INF1? BenQ Returns manufacturer name...
Seite 212
렌즈 크기 ................... 230 RS232 명령 ..................231 RS232 핀 할당 ......................231 크로스오버 케이블이 달린 RS232 직렬 포트 ............231 PJLink ........................239 한 국 어 사용 설명서 / 설치 가이드의 최종 버전을 보려면 아래의 웹사이트를 방문하십시오 . http://business-display.benq.com/ V1.00...
Notice 레이저에 관한 참고사항 이 기호는 지침을 철저하게 준수하지 않을 경우 레이저 광선에 눈이 노출될 수 있는 잠재적 위험을 나타냅니다 y 레이저 등급 ( 미국 ) 이 Laser Product 는 모든 운영 절차에서 Class 3R 로 지정되었고 IEC/EN 60825-1:2007 을 준수합니다 . ( 전...
냉각 관련 참고사항 배기구 주변에 적어도 50 cm (19.7 in) 의 간격을 두십시오 . 30 cm (11.8 in) 이내에 공기 유입 을 차단하는 물체가 없도록 하십시오 . 다른 프로젝터의 공기 유입구와 적어도 1 m 떨어진 곳에 공기 배출구가 오도록 하십시오 . 공기...
Seite 215
• 배기구 주변에 적어도 50 cm 의 간격을 두십시오 . 최소 50 cm 최소 50 cm 최소 50 cm (19.69 in) (19.69 in) (19.69 in) 최소 50 cm (19.69 in) 최소 10 cm (3.94 in) 최소 50 cm (19.69 in) 최소...
방지 캡이 있는 프로젝터 리모컨 배터리 설치 안내서 VGA 케이블 3 핀 VESA-BNC 케이블 전원 케이블 3pin VESA to BNC Cable 사양 LU9255 프로젝션 시스템 DLP 싱글 0.67 WUXGA DMD 칩 1920*1200 픽셀 , 16:10 원시 해상도 한 광원 레이저 다이오드 국...
유선 리모컨을 끼우기 전에 올바른 포트인지 확인하십시오 . 예를 들어 유선 리모컨을 트리거 출력 포트에 연결 하는 식으로 맞지 않는 포트에 끼울 경우 리모컨이 손상될 수 있습니다 . LAN 을 통한 펌웨어 업그레이드에 대한 자세한 내용은 BenQ 서비스 센터로 문의하십시오 .
리모컨 ON / OFF 프로젝터를 대기 모드 또는 켜짐 사이에서 전환합니다 . KEYSTONE+/KEYSTONE- 영사 각도 때문에 사다리꼴이 된 이미지를 수동으로 보정할 수 있습니 다 . VOLUME +/VOLUME - 프로젝터 볼륨을 증가 / 감소시킵니다 . QUICK INSTALL 빠른 설치 OSD 메뉴를 표시합니다 . MUTE 프로젝터를...
Seite 219
OVERSCAN 눌러 오버스캔 모드를 선택합니다 . FREEZE 영사 이미지를 정지시킵니다 . LAMP MODE 눌러 원하는 LIGHT 모드를 선택할 수 있는 OSD 메뉴를 표시합니다 . 3D MODE 눌러 3D 설정 메뉴를 표시합니다 . INFO. 눌러 정보 메뉴를 표시합니다 . LIGHT 눌러 리모컨의 백라이트를 엽니다 . CLEAR 모든...
설치 주의사항 : DLP 칩이 손상되지 않도록 하기 위해 고전력 레이저 빔을 영사 렌즈에 쏘지 않습니다 . 옵션 렌즈 설치 또는 분리하기 주의사항 : • 프로젝터나 렌즈 구성요소에는 정밀 부품이 들어 있기 때문에 이들을 흔들거나 이들에 과도한 힘을 가하지 마십시오 . •...
Seite 221
y 프로젝터에서 기존 렌즈를 분리하기 1. LENSE RELEASE 버튼을 눌러 잠금을 풉니다 . 2. 렌즈를 잡습니다 . 3. 렌즈를 시계 반대방향으로 돌립니다 . 기존 렌즈가 풀립니다 . 4. 기존 렌즈를 천천히 당겨 뺍니다 . 한 국 어...
세미초점 수평 : -5%~5% Projection table *** "A" 는 최대 렌즈 이동 오프셋 위치 55% 를 기준으로 한 길이입니다 . • LU9255 화면비는 16:10 이며 투사 이미지는 16:10 입니다 . 참고 : 한 투사 품질을 최적화하기 위해 그레이스케일이 없는 영역에 이미지를 투사할 것을 권정합니다 .
Seite 223
한 참고 : 국 어 • 보다 시각화된 지침을 보려면 BenQ calculator 웹사이트 http://projectorcalculator.benq.com/ 로 이동하십시오 . • 천장 설치는 자격이 있는 전문가가 설치해야 합니다 . 자세한 내용은 가까운 대리점에 문의하십시오 . 사용자 가 직접 프로젝터를 설치하지 마십시오 . •...
천장 마운트 설치 그림 BenQ 천장 마운트 CMG6(5A.JHS10.001) 번호 재질 스틸 10.5 kg(23.1 파운드 ) 무게 크기 (W x H x D) 410 x 641 x 360 mm(16.14" x 25.24" x 14.17") 491 mm ~ 641 mm 길이 회전 : ± 5°...
RS232 명령 RS232 핀 할당 번호 직렬 번호 직렬 핀 8 에서 단락 핀 7 에서 단락 접지 크로스오버 케이블이 달린 RS232 직렬 포트 ASCII 기능 유형 작동 Power Write Power On <CR>*pow=on#<CR> Write Power off <CR>*pow=off#<CR> Read Power Status <CR>*pow=?#<CR>...
Seite 233
ASCII 기능 유형 작동 Audio Source Write Audio pass Through off <CR>*audiosour=off#<CR> Select Write Audio-Computer1 <CR>*audiosour=RGB#<CR> Write Audio-Video/S-Video <CR>*audiosour=vid#<CR> Write Audio-HDMI <CR>*audiosour=hdmi#<CR> Write Audio-HDMI2 <CR>*audiosour=hdmi2#<CR> Read Audio pass Status <CR>*audiosour=?#<CR> Picture Mode Write Presentation <CR>*appmod=preset#<CR> Write sRGB <CR>*appmod=srgb#<CR> Write Bright <CR>*appmod=bright#<CR>...
Seite 234
ASCII 기능 유형 작동 Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=5#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=5#<CR> Read Brightness value <CR>*bri=?#<CR> Write Color + <CR>*color=+#<CR>...
Seite 235
ASCII 기능 유형 작동 Picture Setting Write 4 Corners Top-Left - X Decrease <CR>*cornerfittlx=-#<CR> Write 4 Corners Top-Left - X Increase <CR>*cornerfittlx=+#<CR> Read 4 Corners Top-Left - X Status <CR>*cornerfittlx=?#<CR> Write 4 Corners Top-Left - Y Decrease <CR>*cornerfittly=-#<CR> Write 4 Corners Top-Left - Y Increase <CR>*cornerfittly=+#<CR>...
Seite 236
ASCII 기능 유형 작동 Operation Set- Write Projector Position-Front Table <CR>*pp=FT#<CR> tings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
Seite 237
ASCII 기능 유형 작동 Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> Read Blank Status <CR>*blank=?#<CR>...
Seite 238
ASCII 기능 유형 작동 Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR>...
Seite 239
ASCII 기능 유형 작동 Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR>...
LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 33 INST? LU9255 list query Projector name Returns the name set in [PROJECTOR NAME] of [NET- NAME? xxxxx query WORK SETUP]...
Seite 241
제어 세부사항 기타 자열 반환 Manufacturer INF1? BenQ Returns manufacturer name name query Model name que- INF2? LU9255 Returns moder name Other informa- INF0? xxxxx Returns information such as version number tion queries Class information CLASS? Returns class for PJLink query 참고...
Seite 245
排気口周辺は、最低でも 50 cm の間隔をあけてください。 • 最低 50 cm 最低 50 cm 最低 50 cm (19.69 インチ) (19.69 インチ) (19.69 インチ) 最低 50 cm (19.69 インチ) 最低 10 cm (3.94 インチ) 最低 50 cm (19.69 インチ) 最低 30 cm (11.81 インチ) 最低...
天井取り付け設置図 番号 BenQ 天井取り付け CMG6 (5A.JHS10.001) 材質 スチール 重量 10.5 kg (23.1 ポンド ) 寸法 ( 幅 x 高さ x 奥行 ) 410 x 641 x 360 mm (16.14 x 25.24 x 14.17 インチ ) 長さ 491mm 〜 641mm 傾斜角...
Seite 264
機能 タイプ 操作 ASCII Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=5#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=5#<CR> Read Brightness value <CR>*bri=?#<CR> Write Color + <CR>*color=+#<CR>...
Seite 265
機能 タイプ 操作 ASCII Picture Setting Write 4 Corners Top-Left - X Decrease <CR>*cornerfittlx=-#<CR> Write 4 Corners Top-Left - X Increase <CR>*cornerfittlx=+#<CR> Read 4 Corners Top-Left - X Status <CR>*cornerfittlx=?#<CR> Write 4 Corners Top-Left - Y Decrease <CR>*cornerfittly=-#<CR> Write 4 Corners Top-Left - Y Increase <CR>*cornerfittly=+#<CR>...
Seite 266
機能 タイプ 操作 ASCII Operation Set- Write Projector Position-Front Table <CR>*pp=FT#<CR> tings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
Seite 267
機能 タイプ 操作 ASCII Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> Read Blank Status <CR>*blank=?#<CR>...
Seite 268
機能 タイプ 操作 ASCII Miscellaneous Write AMX Device Discovery - on <CR>*amxdd=on#<CR> Write AMX Device Discovery - off <CR>*amxdd=off#<CR> Read AMX Device Discovery Status <CR>*amxdd=?#<CR> Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR>...
Seite 269
機能 タイプ 操作 ASCII Color Calibra- Write Blue Offset + <CR>*BOffset=+#<CR> tion Write Blue Offset - <CR>*BOffset=-#<CR> Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR>...
5th byte Return 0 Indicates other errors, and 6th byte returns 0 - 2 Light source sta- LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 33 INST? LU9255 list query...
Seite 271
WORK SETUP] Manufacturer INF1? BenQ Returns manufacturer name name query Model name que- INF2? LU9255 Returns moder name Other informa- INF0? xxxxx Returns information such as version number tion queries Class information CLASS? Returns class for PJLink query 注...