Bosch PSA 18 LI Originalbetriebsanleitung Seite 13

OBJ_BUCH-1848-001.book Page 13 Monday, May 13, 2013 10:57 AM
Technical Data
Sabre saw
Article number
Rated voltage
Stroke rate at no load n
0
Tool holder
Stroke rate control
Stroke
Cutting depth, max.
– in wood
– in non-alloy steel
– Pipe diameter
Weight according to
EPTA-Procedure 01/2003
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 85 dB(A); Sound power level 96 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting board: a =17.5 m/s , K=1.5 m/s
h
Cutting wooden beam: a =17.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Bosch Power Tools
Henk Becker
Executive Vice President
PSA 18 LI
Engineering
3 603 CB2 3..
V= 18
-1
min 0 –2800
SDS Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen

Leinfelden, 29.04.2013
mm 22
Assembly
mm 100
 Before any work on the machine itself (e.g. mainte-
mm 20
nance, tool change, etc.) as well as during transport
mm 20
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
kg 2.3
the On/Off switch.
Battery Charging (see figure B)
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without re-
2
, ducing its service life. Interrupting the charging procedure
2 2
, K=1.5 m/s . does not damage the battery.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Removing the battery
To remove the battery 8, press the battery unlocking button
11 and pull the battery out of the power tool toward the rear.
Do not exert any force.
Replacing/Inserting the Saw Blade
 When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
 When changing the saw blade, take care that the saw
blade holder is free of material residue, e.g. wood or
metal shavings.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of these instructions. Use only ½" universal shank saw
blades. The saw blade should not be longer than required for
the intended cut.
The shank thickness of the saw blade must be 0.8–1.6 mm.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A)
Press the SDS clamping lever 4 forward and guide the saw
blade 1 behind the clamping plate 10 into the saw blade
holder 3. Release the SDS clamping lever 4.
 Check the tight seating by pulling on the saw blade.
A loose saw blade can fall out and cause injury.
English | 13
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 619 X08 257 | (13.5.13)