Cleaning And Maintenance - cecotec Ready Warm 5300 Power Box Ceramic Bedienungsanleitung

ENGLISH
• Use the and buttons on the remote control to set the desired temperature
from 10 ºC to 49 ºC.
• When the room temperature drops 2 degree below the set temperature, the
heater will start heating at "I/W" (1000 W).
• When the air temperature drops 4 degree below the set temperature, the heater
will start heating at "II/H" (2000 W).
• When the room temperature is 1 degree higher or equal to the set temperature,
the heater will blow cold air.
Weekly schedule
Turn the device on and select the desired operating mode through the remote control
following the instruction above.
P6 is the user-defined mode. Use the
select this mode.
To set the turn-on time:
Note: When setting the turn-on time, the "On" indicator will remain on.
• Day: Press the button once, the "Mo" indicator will light on, indicating Monday.
Then, use the "-" and "+" buttons to set the desired day.
• Hour: Press the
button a second time, the LED panel will display "00" blinking.
Then, use the and buttons to set the desired hour, from 01 (1 h) to 00 (24
h).
• Minute: Press the button a third time, the LED panel will display "00" blinking.
Then, use the and buttons to set the desired minutes, from 01 (1 min) to
59 (59 min).
To set the turn-off time:
Note: When setting the turn-on time, the "Off" indicator will remain on.
• Hour: Press the button a fourth time, the LED panel will display "00" blinking.
Then, use the and buttons to set the desired hour, from 01 (1 h) to 00 (24
h).
• Minute: Press the button a fifth time, the LED panel will display "00" blinking.
Then, use the and buttons to set the desired minutes, from 01 (1 min) to
59 (59 min).
After these steps, the heater will be scheduled for the selected day. To continue
scheduling other days:
• Press the button to select the desired day you want the heater to operate:
READY WARM 5300 POWER BOX CERAMIC
and buttons on the remote control to
"Tu", "We"...
• Repeat the steps described for the previous days in order to schedule the rest of
the days of the week.
• Press the button on the remote control when you have finished setting every
week's day turn-on and turn-off time, and set the desired temperature using the
and buttons. Temperature can be set from 10 ºC to 49 ºC.
Note: During the weekly schedule mode, the thermostat function will be activated
automatically.
Open window function
• Turn the device on and select the desired operating mode through the remote control
following the instruction above.
• Press the "Auto" button to activate this function. The
• During this mode, the appliance will operate smartly, saving energy. It will turn off
automatically when room temperature falls by ≥3 ºC within 1 minute.
• If this happens, close the window or door and restart the heater.
• Press the "Auto" button to deactivate this function. The
Note: If the device is not operated after being started up, it will shut down
automatically.

6. CLEANING AND MAINTENANCE

• Disconnect the appliance from the power supply and allow it to cool down before cleaning.
• Use a soft, damp cloth to clean the product's surface.
• Clean dust from the device's surface and vents regularly.
• Clean and store the device in a safe, dry place if it is not going to be used for a long period
of time.
• To open the filter on the back for cleaning, press the top of plastic net at back. Clean any
dust or dirt and install the filter back in its position.
• Do not wet the device and try to avoid contact with water or any other liquids.
• Avoid the use of abrasive cleaning agents or scouring pads as these could damage the
product.
ENGLISH
icon will light on.
icon will turn off.
READY WARM 5300 POWER BOX CERAMIC