Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Quicklinks
Installation Instruction
Replacing sensor A+B
t-mass 150
EA00112D/06/A2/01.12
71183741
Instruction is valid for the following spare part sets:
Order number
6AAB**-**XXXXX******
6BAB**-**XXXXX******
!
Caution!
• The order number of the spare part set (on the packaging label) can differ from the product-number (on the label directly on the spare part)!
• The order number of the relevant spare part set can be found by entering the product-number of the spare part in the spare parts finder.
• We recommend that the Installation Instructions be kept with the packaging at all times.
Confirmation whether the spare part is permitted to be used with the measuring device
The spare parts set and Installation Instructions are used to replace a faulty unit with a functioning unit of the same type.
Use genuine parts from Endress+Hauser only.
Only original spare parts supplied by Endress+Hauser shall be used with the measuring device. Therefore, before use, check whether the spare
part set is compatible with the measuring device.
A spare parts overview label is located in the connection compartment cover of the measuring device. If there is no label or the spare part is not
listed the appropriate spare part can also be identified via W@M Device Viewer.
How carrying out such a check via the W@M Device Viewer is described below:
i
i
1. Choose the Endress+Hauser Device Viewer via web browser: www.endress.com/deviceviewer
2. Enter the serial number (Ser. No.) of the device into the W@M Device Viewer (on the label of the transmitter), then click on "Spare parts".
3. The list of the available spare parts for the device is displayed.
4. Check the order number on the packaging label of the spare part set.
5. Check whether the order number of the spare part set is specified in the list displayed by the device viewer:
= YES, the spare part can be used.
= NO, the spare part may not be used.
If you have any questions, contact your E+H service organization.
Device component
1 × sensor t-mass A 150
1 × sensor t-mass B 150
Device Viewer
Ser. No.:12345
Ser.No.:1234567890
Ser. No.: 12345
www.endress.com/deviceviewer
=
?
A0016264
Werbung
Verwandte Anleitungen für Endress+Hauser t-mass A 150
Inhaltszusammenfassung für Endress+Hauser t-mass A 150
- Seite 1 The spare parts set and Installation Instructions are used to replace a faulty unit with a functioning unit of the same type. Use genuine parts from Endress+Hauser only. Only original spare parts supplied by Endress+Hauser shall be used with the measuring device. Therefore, before use, check whether the spare part set is compatible with the measuring device....
-
Seite 2: Safety Instructions
(for Ex. IECEx, ATEX, FM, CSA, TIIS, NEPSI) 2, 3 1 Trained customer technician 1*Trained customer technician, trained by Endress+Hauser (for repairs carried out on devices with type approval) 2 Service technician authorized by Endress+Hauser 3 Endress+Hauser (send measuring device back to manufacturer) Safety instructions •... - Seite 3 Replacing sensor A+B A Replacing sensor A0017430 A0017431 A0017428 A0017429 A0017432 A0017433 A0017568 0.5 × 3.5 A0017569 A0017570 A0017571 A0017572 45° 4 mm 5 Nm (3.7 lbf ft) A00017574 A0017575 A0017577 A0017578 A0017579 A0017580 B Assembly Unless otherwise specified, installation is the reverse of the removal procedure. Endress + Hauser...
- Seite 4 Replacing sensor A+B Endress + Hauser...
- Seite 5 Ersatzteilset und Einbauanleitung dienen dazu, eine defekte Einheit gegen eine funktionierende Einheit des gleichen Typs zu ersetzen. Es dürfen nur Originalteile von Endress+Hauser verwendet werden. Grundsätzlich dürfen nur Eratzteilsets verwendet werden, die von Endress+Hauser für das Messgerät vorgesehen sind. Vor der Verwendung ist deshalb zu überprüfen, ob das Ersatzteilset zum Messgerät passt....
-
Seite 6: Sicherheitshinweise
Zulassung (z.B. IECEx, ATEX, FM, CSA, TIIS, NEPSI) 2, 3 1 Ausgebildete Fachkraft des Kunden 1*Ausgebildete Fachkraft des Kunden, von Endress+Hauser geschult (für Reparaturen, die an Geräten mit Bauartzulassung vorgenommen werden) 2 Von Endress+Hauser autorisierter Servietechniker 3 Endress+Hauser (Messgerät an Hersteller zurücksenden) Sicherheitshinweise •... - Seite 7 Austausch Messaufnehmer A+B A Austausch Sensor A0017430 A0017431 A0017428 A0017429 A0017432 A0017433 A0017568 0.5 × 3.5 A0017569 A0017570 A0017571 A0017572 45° 4 mm 5 Nm (3.7 lbf ft) A00017574 A0017575 A0017577 A0017578 A0017579 A0017580 B Zusammenbau Der Zusammenbau erfolgt, wenn nicht anders angegeben, in umgekehrter Reihenfolge. Endress + Hauser...
- Seite 8 Austausch Messaufnehmer A+B Endress + Hauser...