Synchronous Recording; Recording Playback Signals From A Vcr With Rs-422A - JVC BD-X200E Bedienungsanleitung

Synchronous Recording

Recording Playback Signals From a VCR with RS-422A

RS-422A control can be used to record playback signals from a VCR with an RS-422A terminal to a disc in your BD-X200.It will also
be possible to control that VCR using this DVD recorder's REMOTE CONTROL screen.
Signal Connections
VIDEO IN
LAN
SIGNAL
GND
USB terminal
Keyboard
Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
！ # あ $ % & お ( ) 〜 =
う え ' や ゆ よ Back
- Space
1 2 3 4 5 6 7 8 9 0 ^ ￥
Q W E R T Y U I O P 「
｀
Tab Enter
@ [
Caps Lock A S D F G H J K L ＋ ＊ 」
; : ]
Z つ X C V B N M < 、 > 。 ? ・ ＿
Shift Shift
, .
/ /
Ctrl Alt Alt Ctrl
● Connect the RS-422A REMOTE terminal on the rear of the DVD recorder to the remote RS-422A terminal on the VCR using an
RS-422A cable.
● Connect the DVD recorder's VIDEO LINE IN and AUDIO IN terminals to the VCR's video out and audio out terminals.
● Connect the DVD recorder's VIDEO LINE OUT and AUDIO OUT terminals to the monitor's video in and audio in terminals.
● A keyboard and mouse can be used as an alternative to the DVD recorder's buttons when using the REMOTE CONTROL screen.
If used, these are to be connected to each of the USB terminals on the rear panel.
Setup Procedures
● Insert the tape for playback into the VCR. Ensure that this tape contains an EBU time code.
● Insert a recordable disc into your BD-X200.
Settings
VCR : Enable control via RS-422A.
BD-X200 : Set REMOTE SELECT from the REMOTE MENU screen to 9PIN (MASTER).
REMOTE MENU screen
REMOTE MENU
MENU
REMOTE SELECT
REC CONTROL
REM FF/REW MODE
Note
When pressing and holding the REC
button more than 2 seconds while the DVD
recorder is stopped, encoded output
images can be checked while the button
is being held.
All manuals and user guides at all-guides.com
VIDEO OUT
AUDIO IN
VIDEO AUDIO
IN LINE OUT INPUT
CH1
LEVEL
IN OUT
4dB
8dB
AUDIO OUT
Y/C
IN
CH2
REMOTE
DV IN/OUT
REMOTE
USB
DC 19V
Print
Scroll Pause
Screen
Lock
Sysrq Break
Page Num -
Insert Home / *
Up Lock
7 8 9
Page
Delete End
Down
+
4 5 6
Mouse
1 2
Enter
.
0
● When REMOTE SELECT is set to 9PIN (MASTER), the REMOTE CONTROL
(9PIN MASTER) screen will appear. This screen is used to perform editing
operations, and the corresponding operations are described on the following
pages.
9PIN(MASTER)
OFF
FF/REW
AUDIO OUT
AUDIO VIDEO
AUDIO INPUT / AUDIO MONITOR SELECT
INPUT INPUT
SDI CH1 CH2 CH3 CH4 SIF
AUDIO AES/EBU CH1 LINE
CH2 CH3 CH4
MONITOR L
ANALOG
CH1 CH2 CH3 CH4 CPN
R
CH1 CH2 CH3 CH4/ TRACKING
R P R P R P R P
dB OVER dB dB OVER dB dB OVER dB dB OVER dB
0 0 0 0
+4 +4 +4 +4
–10 –10 –10 –10
+2 +2 +2 +2
0 0 0 0
–20 –20 –20 –20
–2 –30 –2 –30 –2 –30 –2 –30
–40 –40 –40 –40
–4 –4 –4 –4
–60 –60 –60 –60
CH1 CH2 CH3 CH4
PHONES
REC
PULL FOR VARIABLE METER MODE
FINE
PULL
RELEASE
PLAY
VCR with an RS-422A terminal
Monitor
REMOTE CONTROL (9PIN MASTER) screen
REMOTE CONTROL SCREEN ( 9PIN MASTER )
EXIT IN POINT 00:00:00:00 OUT POINT
: : : : : :
h m s f h m s f
1 00:00:00:00 2 00:15:00:00
4 5
00:25:00:00 00:30:00:00
7 8
00:40:00:00 00:45:00:00
TC INPUT
CHAPTER MANUAL
ADJ
BITRATE 8.0 Mbps DISC REMAIN
TC SET
EDL LOAD
TC CANCEL EDIT/END
VIDEO OUT
VIDEO CASSETTE RECORDER
POWER
ON I
OFF O
Variable Motion
SEARCH VAR PLAYER RECORDER
COUNTER RESET VCON REMOTE
CTL TC UB DF SERVO CF GEN 16:9 AP 525 CONDITION
AUTO OFF P.READ V.V A R PB/EE R E M O TE 625
UB
PB
MENU SET HOLD PB/EE P.PLAY
STILL
H M S F
ASSEM VIDEO DA1 DA2 DA3 DA4 EJECT REC PLAY
PAUSE/STILL
X-1 X1
TRACKING
IN ENTRY OUT INSERT TC
TOP VIDEO AUDIO
STAND BY REW STOP FF
AUTO EDIT
CANCEL PREVIEW PREROLL
TRACKING
PULL
RELEASE
SHIFT REVIEW SERVO/SYS TIME CODE ON SCREEN OTHERS
USER REV FWD
MONITOR OUT
Monitor
00:10:00:00
: : :
h m s f
3 00:20:00:00
6
00:35:00:00
9
00:50:00:00
: :
000 min
FINALIZE
E-59