Maintenance - Makita CL114FD Betriebsanleitung

Disposing of dust
CAUTION:
Empty the cleaner before it
becomes too full, or the suction force weakens.
CAUTION:
When closing the front cover, be
careful not to pinch your fingers.
NOTICE:
Never throw away the dust stopper
because it should be used whenever either the
dust bag or the paper filter is used.
NOTICE:
When the dust bag/paper filter is not
inside of the cleaner, the front cover does not
close completely. Do not force to close the front
cover. It may result in deforming or breakage of
the cleaner.
NOTICE:
When disposing of dust, also clean the
room for the dust bag/paper filter. The remaining
dust and dirt in the room may cause the sponge filter
to be clogged or the motor to be damaged.
1.
Push the button to open the front cover. Opening
it until a click is heard allows a positive stop at that
position.
► Fig.31: 1. Front cover 2. Button
2. Pull out both the orange-colored dust stopper and
dust bag/paper filter together at the same time.
► Fig.32: 1. Dust stopper
3.
Perform the procedures below depending on the
dust container type:
When using the dust bag
Remove the dust stopper and empty the dust bag.
► Fig.33: 1. Dust stopper 2. Dust bag
When using the paper filter
Remove the dust stopper and dispose of the paper filter.
► Fig.34: 1. Dust stopper 2. Paper filter
4. Place the dust bag/new paper filter and dust stop-
per together into the cleaner and close the front cover.
NOTE: The cleaner is constructed in such a way that
the front cover comes off when trying to force the
front cover open at the angle of more than 90°. If the
front cover comes off, insert it into the front cover joint
in place.
► Fig.35: 1. Front cover 2. Front cover joint

MAINTENANCE

CAUTION:
Always be sure that the appliance
is switched off before attempting to perform
inspection or maintenance.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
After use
When storing or charging the cleaner, lock the nozzle
head, and hang it from a hook available in the market.
► Fig.36
CAUTION:
Putting the cleaner against the
wall without any other support may cause the
cleaner to fall down and be damaged.
► Fig.37
Cleaning
Cleaner body
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/paper filter
mounting area and the dust stopper.
► Fig.38
Dust stopper
Wipe dust off from the dust stopper.
Remove dust and dirt on the sponge part by lightly
tapping it.
► Fig.39: 1. Sponge part
Dust bag
Wash the dust bag in soapy water when it is clogged
with dust and the cleaner power becomes weak. Dry it
out thoroughly before use. An insufficiently dried bag
may cause poor suction and shorten the service life of
the motor.
► Fig.40
NOTE: Paper filter is a throw-away type.
When the sponge filter is clogged with dust, remove it
from the cleaner and then wipe it off or wash in water.
Removing and installing the sponge
filter
CAUTION:
After cleaning sponge filter, be
sure to install it on the cleaner. If washed in water,
dry it up before installing. An insufficiently dried
sponge filter may shorten the service life of the motor.
To remove the sponge filter, remove the dust bag or
paper filter and then pinch and take the sponge filter
out.
► Fig.41: 1. Sponge filter
To install the filter, press in the whole edge of the
sponge filter against the recessed wall inside the dust
bag/paper filter mounting area.
► Fig.42: 1. Recessed wall
The nozzle cleaning
(country specific)
When the nozzle brush gets dusty, clean up the dust
with adhesive tape.
► Fig.43: 1. Brush
13 ENGLISH