Standard Accessories; Battery Removal/Installation - Hitachi DS 9DVC Bedienungsanleitung

English

STANDARD ACCESSORIES

In addition to the main unit (1), the package contains the
accessories listed in the table below.
1 Plus driver bit (No. 2 × 65L) .................... 1
2 Charger
(UC18YK or UC9SF or UC12SF) ............ 1
DS9DVC
3 Battery .................................................... 2
DS12DVC
or
Battery .................................................... 1
4 Plastic case ............................................ 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
1. Battery (BCC912)
(For DS9DVC)
2. Battery (BCC1212)
(For DS12DVC)
Optional accessories are subject to change without notice.
APPLICATIONS
○ Driving and removing of machine screws, wood screws,
tapping screws, etc.
○ Drilling of various metals.
○ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch (2 pcs.)
to remove the battery (see Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
Before using the driver drill, charge the battery as follows.
1. Connect the charger power cord to the receptacle
Connecting the power cord will turn on the charger.
2. Insert the battery into the charger
Insert the battery fi rmly while observing its direction,
until it contacts the bottom of the charger (See
Fig. 3, 4). (The pilot lamp on the UC18YK or the battery
set lamp on the UC9SF or UC12SF lights up.)
CAUTION
If the pilot lamp on the UC18YK or the battery set
lamp on the UC9SF or UC12SF does not light up
when the battery is inserted, pull out the power cord
from the receptacle and check the battery mounting
condition.
(1) Regarding the temperatures of the rechargeable battery
The temperatures for rechargeable batteries are as
shown in Table 1.
8
Table 1 Recharging ranges of batteries
Rechargeable batteries
BCC912, BCC1212
(2) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 2.
Table 2 Charging time (At 20°C)
Charger
UC18YK
Battery
Approx.
BCC1212
50 min.
Approx.
BCC912
50 min.
UC18YK:
The pilot lamp goes off to indicate that the battery is fully
charged.
The battery charging time becomes longer when a
temperature is low or the voltage of the power source is
too low.
UC9SF or UC12SF:
Using the above times as a guide, remove the battery
from the charger.
The battery set lamp goes off when the battery is removed
from the charger.
When the temperature of the battery is low (less than 0°C)
or the voltage of the power source is low, the capacity
of the battery after charging for 180 minutes is reduced.
If the battery performance seems poor during practical
use, charge for 4 to 6 hours.
CAUTION
If the battery is heated due to direct sunlight, etc.,
just after operation, the charger pilot lamp may not
light up. At that time, cool the battery fi rst, then start
charging.
3. Disconnect the charger's power cord from the
receptacle
4. Hold the charger fi rmly and pull out the battery
NOTE
After charging, pull out batteries from the charger fi rst,
and then keep the batteries properly.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2 – 3 times.
Temperatures at
which the battery
can be recharged
0°C – 45°C
UC12SF UC9SF
Approx.
180 min.
(Less than ––––––––
0°C: Approx.
4 to 6 hours)
Approx.
180 min.
–––––––– (Less than
0°C: Approx.
4 to 6 hours)